Translucency parameter of conventional restorative glass-ionomer cements.

OBJECTIVE: To evaluate the translucency parameter (TP) and contrast ratio (CR) of different conventional restorative glass-ionomer cements (GICs). MATERIALS AND METHODS: Eighteen brands of GICs were evaluated. Five disks of each material were made following ISO 9917-1. The luminous reflectance and Central Bureau of the International Commission on Illumination parameters of disks were evaluated using a colorimeter, against backings of white and black, to obtain the translucent parameter and contrast ratio of different brands of glass-ionomer cements. The correlation between translucency parameter and contrast ratio was assessed with the Pearson correlation test. The translucent and contrast ratio parameters values were submitted to the one-way ANOVA and Tukey test for multiple comparisons (p < 0.05). RESULTS: There was a strong inverse relationship between CR and TP (r2  = 0.94, p < 0.001). The contrast ratio decreased as translucency increased. There were significant differences in TP and CR among brands (p < 0.001). CONLUSIONS: GICs exhibit different translucency and contrast ratio behavior. Some brands of GICs presented very low TP and this condition would be unacceptable for areas with esthetic demands. In addition, TP and CR showed a strong linear relationship. CLINICAL SIGNIFICANCE: The results found in this study demonstrated that the knowledge of the translucency and CR of different conventional restorative GICs is important in order to guide clinicians in the selection of restorative GICs for anterior teeth.

Susceptibility to Coffee Staining during Enamel Remineralization Following the In-Office Bleaching Technique: An In Situ Assessment.

PURPOSE: To assess in situ the enamel mineralization level and susceptibility to coffee staining after in-office bleaching. MATERIALS AND METHODS: Thirty-six human dental fragments assembled into intraoral devices were bleached with 35% hydrogen peroxide and treated as follows: (group 1) no contact with coffee; (group 2) immersion in a coffee solution for 30 minutes daily for 7 days, starting 1 week after bleaching; and (group 3) immersion in a coffee solution for 30 minutes daily for 14 days, starting immediately after bleaching. Enamel mineralization and color were assessed before bleaching (T1), immediately after bleaching (T2), and after 7 (T3) and 14 days (T4). The CIE whiteness index (W*) and closeness to white (ΔW*) following bleaching and/or immersion in coffee were calculated. Data were analyzed with Friedman and Wilcoxon tests or Kruskal-Wallis and Mann-Whitney U-tests (α = 0.05). RESULTS: Significant differences in the mineralization levels were observed as a function of time. No significant differences in W* were observed between groups, nor was W* significantly different at T3 and T4. Similar ΔW* was observed between groups after 7 or 14 days. CONCLUSIONS: The mineral loss after in-office bleaching was progressively reversed by contact with saliva for 14 days. The whiteness index was not affected by contact with coffee during the remineralization period. CLINICAL SIGNIFICANCE: The results of this in situ study suggest that the mineral loss caused by in-office dental bleaching is minimal and is partly compensated by remineralization due to contact with saliva. Additionally, whiteness was not affected by daily exposition to coffee during the enamel remineralization, which indicates that avoiding the consumption of coffee immediately following in-office bleaching is unnecessary. (J Esthet Restor Dent 28:S23-S31, 2016).

Color stability over time of three resin-based restorative materials stored dry and in artificial saliva.

OBJECTIVE: To evaluate the color match of different composite resins relative to Vitapan Classical shade guide tab and their respective manufacturers' shade guide tabs as a function of time and storage. MATERIALS AND METHODS: Three enamel shade A2 composite resins were used to fabricate 36 disk-shaped polymerized specimens (12 each), allocated into 2 groups of 6 and stored dry (GD) and in artificial saliva (GS). CIELAB coordinates from shade tabs and resin specimens immediately after polymerization (t0), and 24 hours (t1), 7 (t7), 14 (t14) and 21 (t21) days after polymerization were captured using a colorimeter. Color difference (ΔE00 ) between composite specimens and the reference tabs was calculated using the CIEDE2000 formula. The results were analyzed with repeated measures ANOVA, Tukey's HDS post-hoc test, and Student t test (p ≤ 0.05). RESULTS: Color of the three tested composites relative to Vita and their respective tabs significantly changed as a function of time until t14; however, between t14 and t21, no significant differences were found. No differences in color were found relative to storage at t14 and t21. ΔE00 values of specimens at t14 were significantly higher relative to their respective tabs than to Vitapan tab. CONCLUSIONS: For all brands color changed up to day 14, when it stabilized, regardless of whether composite specimens had been stored in artificial saliva or simply in a box. Vitapan tab presented a better color match than the manufacturers' tabs. CLINICAL SIGNIFICANCE: The results found in this study demonstrated that the Vitapan Classical shade guide tab A2 provided a better color match than the respective shade guide tabs A2 supplied by the composite manufacturers. If custom shade tabs are to be made, however, they could be kept in a box and used as shade references from 14 days after being fabricated, when color stabilizes.

Smile attractiveness of patients treated for congenitally missing maxillary lateral incisors as rated by dentists, laypersons, and the patients themselves.

STATEMENT OF PROBLEM: Esthetic judgments can help dental professionals better understand how attentive people are to their own smiles and those of others. PURPOSE: The purpose of this study was to evaluate the smile attractiveness of patients treated for maxillary lateral incisor agenesis compared with that of individuals with a complete dentition. MATERIAL AND METHODS: Photographs were made of the smiles of patients with maxillary lateral incisor agenesis who were treated with space closure and teeth recontouring (n=26) or space opening and implants (n=20) and of a control group with a complete dentition (n=22). Both laypersons and dentists assessed smile attractiveness by using a visual analog scale. Patients and controls also assessed the level of satisfaction with their own smile. Assessments were performed twice, and the reliability of the method was determined with Cronbach α and intraclass correlation. Multifactorial and 1-way ANOVA were used to analyze smile attractiveness and participant satisfaction, followed by the Bonferroni post hoc test (α=.05). RESULTS: Attractiveness ratings by dentists and laypersons did not differ significantly among the study groups (P=.64). The ratings of male dentists and female laypersons differed significantly from those of other evaluators (P=.01). Patients with space closure and teeth recontouring were significantly more satisfied than controls (P=.002). No significant differences were found between the patients with implants and controls or between the patients with implants and those with space closure and teeth recontouring. CONCLUSIONS: The smiles of patients with maxillary lateral incisor agenesis were judged to be as attractive as those of the controls. Male dentists were the most critical raters, closely followed by female laypersons. All participants had high levels of satisfaction with their own smile; patients treated with space closure and teeth recontouring were the most satisfied.

Periodontal indexes of two types of 3 x 3 retainers: 0.032-in SS V-loop versus 0.0215-in SS coaxial - a randomized crossover trial.

OBJECTIVE: This randomized crossover trial evaluated periodontal indexes of two types of 3 x 3 retainers (a modified 0.032-in SS V-loop retainer and a conventional 0.0215-in SS coaxial wire retainer) after bonded for six months. Also, bonded failure rate, and a questionnaire about comfort, ease of cleaning and overall preference were recorded. MATERIAL AND METHODS: 15 patients were enrolled in this study who used both retainers for six months each, having a 15-day wash-out interval between each bonded retainer usage. The following periodontal index were recorded: Plaque Index (PI), Calculus Index (CI) and Gingival Index (GI). Patients answered a questionnaire to assess comfort, ease of cleaning and overall retainer-type preference. Rate of bonding failure was also evaluated. RESULTS: V-Loop retainer showed higher PI (P<0.05) as compared to conventional 0.0215-in coaxial wire retainer. However, CI and GI presented no statistically significant differences between both types of retainers. The conventional 0.0215-in coaxial wire retainer was chosen as the most comfortable (p<0.05), although no statistically significant differences were found for all other questionnaire answers. Bonding failure events were more observed in the 3x3 V-Loop retainer (p<0.002), as compared to the conventional 0.0215-in coaxial retainer. CONCLUSION: V-Loop retainer showed higher PI (p<0.05), higher bonding failure rate and less comfortable, as compared to conventional 0.0215-in coaxial wire.

Digital analysis of anterior dental esthetic parameters in patients with bilateral maxillary lateral incisor agenesis.

OBJECTIVE: To analyze anterior dental esthetic parameters-width/height ratio (WHR), gingival zenith (GZ), and apparent contact dimension (ACD)-in patients with maxillary lateral incisor agenesis (MLIA) bilaterally treated with space closure and recontouring of the canines, or with implant-supported prostheses. METHODS: Fifty-two participants were allocated into three groups as follows: MLIA patients (N = 18) treated with teeth recontouring (RG); MLIA patients (N = 10) treated with implants (IG); and volunteers without agenesis (N = 24), who served as controls (CG). Dental casts of all patients were obtained and electronically scanned. Digital images were analyzed with 3Shape A/S OrthoAnalyser software (Copenhagen, Denmark). Shapiro-Wilk test, Spearman correlation, and Kruskal-Wallis statistical tests (p < 0.05) were used for statistical analysis. RESULTS: Although IG presented smaller means when compared with RG and CG, no statistical differences were found for WHR among groups (p > 0.05). Concerning GZ, RG presented more discrepancies than IG and CG, with statistically significant differences (p = 0.0165). IG presented statistically significant differences for the ACD in comparison with RG and CG (p < 0.05). CONCLUSION: Based on the results of this study, patients treated with space closure and teeth recontouring (RG) were shown to be closest to patients without agenesis (CG) in relation to the anterior dental esthetic parameters evaluated. CLINICAL SIGNIFICANCE: The digital analysis of esthetic principles, such as those investigated in this study involving maxillary incisor agenesis, is paramount to successful esthetic treatment planning. The results of the present study, as well as those found in the literature, indicate that clinicians should use esthetic parameters, such as those investigated herein, when treatment planning extensive oral rehabilitation cases.

Analysis of the golden proportion and width/height ratios of maxillary anterior dentition in patients with lateral incisor agenesis.

OBJECTIVE: The purpose of this study was to assess the presence of the golden proportion (GP) in the facial view tooth-to-tooth width proportion of the six maxillary anterior teeth and to evaluate the width/height (W/H) ratios of the incisors of patients with maxillary lateral incisor (LI) agenesis treated either with implants or orthodontically (by moving canines into the position of the laterals, recontouring them, and placing composite restorations over the repositioned teeth). MATERIALS AND METHODS: Forty-eight patients with LI agenesis were divided into four experimental groups: unilateral recontouring group (N = 10), bilateral recontouring group (BRG, N = 18), unilateral implant group (UIG, N = 10), bilateral implant group (N = 10), and a control group (CG, N = 25) of patients without agenesis. GP ratios were determined on patients' dental casts placed over Levin's grids, whereas W/H ratios were measured directly on the casts and a millimeter ruler to determine these distances. Statistical analysis was performed with Shapiro-Wilk, Kruskal-Wallis, Mann-Whitney, Friedman, and Wilcoxon tests (p < 0.05). RESULTS: The incidence of GP in the tooth-to-tooth width proportions was significantly different between groups and more commonly found between centrals and laterals than between laterals and canines. The GP was more likely to be observed in the BRG, UIG, and CG. The results demonstrated that the GP was not found to be present in the majority of the cases treated with maxillary agenesis, regardless of the method of treatment. The mean W/H ratios of the laterals ranged between 0.75 and 0.90. CONCLUSION: Although the GP may be a useful diagnostic guide, it was not observed in the majority of esthetic outcomes of patients treated with maxillary LI agenesis in this study. CLINICAL SIGNIFICANCE: The assessment of the golden proportion and width/height ratio of upper anterior teeth in patients with upper lateral incisor agenesis treated with either implants or tooth re-contouring may assist dentists and patients in deciding the best treatment option based on the peculiarities of each case.

Evaluation of biofilm formation on acrylic resin surfaces coated with silicon dioxide: an in situ study.

Biofilm on acrylic resin dental prostheses may cause gingival inflammation. This study evaluated the influence of a silicon dioxide coating layer applied onto acrylic resin on the adhesion of microorganisms. Blocks (5 x 5 x 3 mm) of acrylic resin were evaluated for surface roughness and divided into two groups: control (CG) and coated with silicon dioxide (LG group). The specimens were evaluated by scanning electron microscopy (n = 1) and by contact angle analysis (n = 3). For the in situ study, 20 volunteers wore acrylic palatal devices containing three samples from each group (n = 60) for 2 days. The biofilm formed was quantified by metabolic activity and total biomass using the crystal violet assay. The results were subjected to Bartlett's normality test and Gamma model with random effect for the response variable (α = 5%). The mean contact angle of the coated group was significantly lower than that of the uncoated group (p < 0.05). The metabolic activity of microorganisms in the biofilm on the blocks treated with coating was significantly lower than that of control blocks (p = 0.02). Regarding the amount of extracellular matrix produced by the microorganisms, there was no difference between the CG and LG group (p = 0.05). The application of a silicon dioxide coating on acrylic resin reduced the activity of the polymicrobial biofilm formed in situ. This coating may be advantageous for patients with conventional complete dentures or implants made of acrylic resin and who have motor difficulties that prevent them from cleaning their prostheses properly.

Interdisciplinary treatment for a patient with open-bite malocclusion and amelogenesis imperfecta.

Amelogenesis imperfecta (AI) comprises a clinically and genetically heterogeneous group of conditions that affect the dental enamel, occasionally in conjunction with other dental, oral, and extraoral tissues. The aim of this case report is to describe an interdisciplinary treatment of hypoplastic AI associated with a severe open bite. The treatment consisted of surgical, orthodontic, periodontal, prosthetic and restorative management, establishing good chewing function, dental esthetics and facial harmony.

Hypomineralized Teeth Have a Higher Frequency of Dental Hypersensitivity.

Purpose: The purposes of this study were to: (1) compare dental hypersensitivity (DH) between hypomineralized permanent first molars and unaffected controls molars in patients with molar-incisor hypomineralization (MIH); and (2) assess the influence of opacity, color, and subject age on DH. Methods: This cross-sectional study identified 40 children/adolescents, who were attending a children's dental clinic and had one to three first permanent molars hypomineralized (demarcated opacities). The severity and color of the hypomineralized lesions were also evaluated. The assessment of DH was made using evaporative stimulus using a jet of compressed air applied by a dental syringe for one second, perpendicular to the occlusal surface employing the visual analogue scale (VAS) and the Schiff cold air sensitivity scale (SCASS). To verify the association between the presence or absence of DH and MIH, Pearson's chi-square and Fisher's exact test (P<0.05) were performed. Results: The frequency of DH was 28.0 percent in hypomineralized teeth and 9.4 percent in normal controls (by VAS; P=0.002). A higher frequency of opacities was observed (P<0.001). Older individuals had DH more frequently (P<0.05). Conclusions: Hypomineralized molars presented a higher frequency of dental hypersensitivity than control teeth, and dental hypersensitivity was associated with darker opacities of the lesion and older-aged subjects.

Consensus on glass-ionomer cement thresholds for restorative indications.

OBJECTIVE: The aim of this paper is to present the results of a consensus meeting on the threshold property requirements for the clinical use of conventional glass-ionomer cements (GICs) for restorative indications. METHODS: Twenty-one experts on GICs evaluated the results of tests on mechanical and optical properties of 18 different brands of restorative GICs: Bioglass R [B], Chemfil Rock [CR], Equia Forte [EF], Gold Label 2 [GL2], Gold Label 9 [GL9], Glass Ionomer Cement II [GI], Ionglass [IG], Ion Z [IZ], Ionomaster [IM], Ionofil Plus [IP], Ionostar Plus [IS], Ketac Molar Easymix [KM], Magic Glass [MG], Maxxion R [MA], Riva Self Cure [R], Vidrion R [V], Vitro Fil [VF] and Vitro Molar [VM]. All experiments were carried out by a team of researchers from Brazil and England following strict protocols, under the same laboratory conditions throughout, and maintaining data integrity. RESULTS: There was consensus on: determining as primary properties of the material: compressive strength, microhardness, acid erosion and fluoride release, and as secondary properties: contrast ratio and translucency parameter, in order to rank the materials. Seven brands were below the thresholds for restorative indications: IZ, IM, IG, MA, VF, B and MG. CONCLUSIONS: Based on the primary properties adopted as being essential for restorative indications, the conventional restorative GICs that met the thresholds and could be considered suitable as long-term restorative materials were: EF, GI, GL9, KM, IP, GL2, IS, CR, V, VM and R. A decision-making process to select the best GIC must also include results from clinical trials. CLINICAL SIGNIFICANCE: This study provides a ranking of GICs that could be considered suitable as long-term restorative materials based on their main properties.

Stepwise excavation in a permanent molar: 17-year follow-up.

The current study presents a 17-year clinical report of stepwise excavation and indirect pulp capping in a lower right first molar, with great dentin destruction and a lack of dentin support of the cusps. At the first appointment, indirect pulp capping with calcium hydroxide and a temporary filling with zinc oxide cement were performed to minimize the risk of pulp exposure during excavation. After 45 days, the remaining carious tissue was removed and a restoration with glass-ionomer lining (Vitrebond) and resin composite (P-50) was performed. Satisfactory morphology and function of the restoration and pulp vitality were preserved for 17 years, thus indicating that stepwise excavation can be a good treatment alternative in selected cases.

System dynamics modeling for tooth decay treatment in Brazilian children.

Prevention and health promotion are considered important strategies to control oral diseases. Dental caries is preventable disease and remains the most common chronic disease that affects mainly low income children and still considered the main cause of tooth loss in adulthood in Brazil. The aim of this study is to present a System Dynamics model (SDM) specifically developed with the Stella Architect software to estimate the cost and clinical hours required to control the evolution of dental caries in preschool children in Maringá, Brazil. Two main strategies to control caries were considered in the model: the application of fluoride varnish on teeth presenting white spots, and the use of Atraumatic Restorative Treatment (ART) in cavitated carious lesions without pulp involvement. The parameters used in the model were: number of people covered by a local oral health team = 4,000; number of children up to 5 years = 7% of the population; children's decayed, missing, filled teeth (dmft) index = 2.4; time/cost of 4 applications of fluoride varnish = 5 minutes/US$ 0.716; and time/cost of each ART restoration = 15 minutes/US$ 1.475. The SDM generated an estimated total cost of US$698.00, and a total of 112 clinical hours to treat the population in question. The use of the SDM presented here has the potential to assist decision making by measuring the material and human resources required to prevent and control dental caries at an early age.

Mechanical and Chemical Changes in the Adhesive-Dentin Interface after Remineralization.

PURPOSE: To evaluate the remineralization effects of Bioglass 45S5 (BAG) on dentin composition, adhesive-dentin bond strength, as well as interface and diffusion zone thickness. MATERIALS AND METHODS: Dentin specimens were assigned to a control group (CG), in which the adhesive was applied following the manufacturer's instructions, and a remineralized group (RG), in which remineralization treatment was carried out by rubbing a remineralization solution (0.015 g of BAG with 1.35 ml of distilled water) on the etched dentin surface for 30 s before applying the adhesive. For bioactive analysis (n = 10), control and remineralized dentin were investigated using micro-Raman spectroscopy (mRS) and scanning electron microscopy (SEM). Stick specimens prepared with a three-step etch-and-rinse adhesive were submitted to a microtensile bond strength (µTBS) test (n = 10) after 24 h (24 h) and eight months (8 m). Micro-RS 3D-maps (n = 10) characterized the adhesive-dentin interface composition and diffusion zone thickness, and SEM images (n = 10) evaluated interface thickness. Data were analyzed using Student's t-test or two-way ANOVA and Tukey-Kramer's post-hoc test (α = 0.05). RESULTS: Remineralization treatment increased the mineral content of dentin. Mean µTBSs were statistically different at 24 h, with RG higher than CG; however, this difference was not significant at 8 m. When the adhesive was applied on remineralized dentin, its penetration was reduced, its physical interaction with phosphate was improved, and its degree of conversion increased. The diffusion zone in the CG did not differ from that of the RG, and interface thickness values of the CG did not differ from that of the RG. CONCLUSION: Remineralization treatment promoted mineral growth on the dentin surface, improved the interaction of dentin with adhesive monomers, and consequently resulted in higher immediate bond strengths.

Effect of Silicon dioxide coating of acrylic resin surfaces on Candida albicans adhesion.

Acrylic resin has been used in the manufacture of prostheses, however, in the oral cavity, this material starts to retain microorganisms capable of causing gingival inflammation due its porosities. The aim of this study was to evaluate the influence of the use of silicon dioxide as a coating layer applied onto acrylic resin, on the adhesion of Candida albicans (Ca). After the incubation period in Sabouraud Dextrose Broth, a total of 1 ml of the Ca suspension was added to plate wells, each well containing a specimen of acrylic resin. The adhesion ability of Ca on acrylic resin was determined by counting colonies. Three groups (n = 6) of acrylic resin were assessed: with polishing (RP); without polishing (RW); with polishing and coating layer of silicon dioxide (RPC). Ca deposited on the surface of the acrylic resin was also observed using Scanning Electron Microscopy (SEM). Statistical assessment by Kruskal-Wallis and Student-Newman-Keuls Method were done (α = 2%). There was significant difference among the groups. The RPC group showed the lowest growth, with an average of 5.59 Log CFU/cm 2 ; there was a statistically significant difference in relation to group RW, which presented a growth of 6.07 Log CFU/cm 2 and to group RP with 5.91 Log CFU/cm 2 (p < 000.1). SEM images demonstrated that in the RP and RPC group, the surface of the resin had greater regularity, and smaller number of microorganisms. The application of silicon dioxide coating on acrylic resin appears to be a promising alternative, and its use can help in reducing the adhesion of Ca in prostheses.

Correlation between mechanical properties and stabilization time of chemical bonds in glass-ionomer cements.

The objective was to evaluate the compressive strength (CS), diametral tensile strength (DTS), flexural strength (FS), and Knoop microhardness (KH) of different conventional restorative glass-ionomer cements (GICs) and to correlate these mechanical properties (MP) with the stabilization time (ST) of their chemical bonds. Eighteen GICs were tested: Bioglass [B], Chemfil Rock [CR], Equia Forte [EF], Gold Label 2 [GL2], Gold Label 9 [GL9], Glass Ionomer Cement II [GI], Ionglass [IG], Ion Z[ IZ], Ionomaster [IM], Ionofil Plus [IP], Ionostar Plus [IS], Ketac Molar Easymix [KM], Magic Glass [MG], Maxxion R [Ma], Riva Self Cure [R], Vidrion R [V], Vitro Fil [VF] and Vitro Molar [VM]. The mechanical strength tests were performed in a universal testing machine. KH readings were done with a diamond indenter. STs were examined by Fourier Transform Infrared spectroscopy (FTIR). Data were analyzed with ANOVA and Tukey test (p<0.05). The Spearman rank test was used to evaluate the dependence between the MPs and ST results. The highest MP values were EF, GL2, GL9, GI and KM and the lowest for MG, MA, B, VF and IM. The longest ST was for GL2 and the shortest was for B. ST correlated positively with MP. GICs with longer chemical bonds ST are generally stronger and the ST value obtained from FTIR was useful in predicting the strength of GICs tested.

ORAL HEALTH PROMOTION IN PATIENTS WITH MORBID OBESITY AFTER GASTROPLASTY: A RANDOMIZED CLINICAL TRIAL.

BACKGROUND: The bariatric surgery may have negative repercussions on oral conditions. AIM: To evaluate the impact of oral health educational/preventive program developed with patients submitted to gastroplasties. METHOD: The sample consisted of 109 patients randomly allocated to two groups: intervention group (IG), where they participated in the oral health promotion program that include multiple educational-preventive approaches; control group (CG), where they received usual care from the bariatric clinic staff, without participation in the program. The oral conditions investigated in the pre-operative and postoperative periods of one month (1M) and six months (6M) were: dental caries, periodontal disease, tooth wear, dental plaque and salivary flow. RESULTS: After bariatric surgery, patients in IG presented: fewer changes in enamel (6M: p=0.004), dentin (6M: p=0.005) and gingival bleeding (6M: p<0.0001), reduction in plaque index (1M, 6M: p<0.0001) and increased salivary flow (6M: p=0.039), when compared with CG. Incipient tooth wear was recorded in both groups (6M: p=0.713). CONCLUSION: There was a positive impact of the implemented program in the prevention of the main oral health problems in patients who underwent gastroplasties, contributing to their quality of life.

Use of sonic waves in bubble formation, microhardness and fluoride release of a high-viscosity glass-ionomer cement.

AIM: High-viscosity glass-ionomer cements (HV-GIC) are indicated for restorations but their viscosity favors the inclusion of bubbles within it. This study aimed to evaluate the use of ultrasonic and sonic waves in bubble formation, microhardness and fluoride release in a HV-GIC, also considering a different powder:liquid ratio (P/L). METHODS: Twenty-four molars with occlusal cavities were divided into four groups (N = 6): CG, HV-GIC with manual insertion; UG, application of ultrasonic waves; SG, application of sonic waves; and FG, HV-GIC fluid (1:2 P/L) with manual insertion. After 24 hours, bubbles and microhardness (50 g/5 s) were measured. Fluoride release (N = 10) was evaluated in CG, SG and UG after cariogenic challenge for 11 days. Microhardness, total area and number of bubbles, and fluoride release were submitted to ANOVA and Tukey's test. The average size of bubbles was analyzed by Kruskal-Wallis test (α = 5%). RESULTS: FG presented the lowest value of microhardness and higher average size for bubbles (P < .05). Differences concerning total number, total area occupied by bubbles and fluoride release were not found (P > .05). CONCLUSION: The use of sonic and ultrasonic waves had no influence on bubble formation, microhardness and fluoride release of a HV-GIC. Changing the P/L is not recommended.

Mechanical and optical properties of conventional restorative glass-ionomer cements - a systematic review.

OBJECTIVES: To perform a systematic review of test methodologies on conventional restorative glass-ionomer cement (GIC) materials for mechanical and optical properties to compare the results between different GICs. MATERIAL AND METHODS: Screening of titles and abstracts, data extraction, and quality assessments of full-texts were conducted in search for in vitro studies on conventional GICs that follow the relevant specifications of ISO standards regarding the following mechanical and optical properties: compressive strength, flexural strength, color, opacity and radiopacity. SOURCES: The Latin American and Caribbean Health Sciences (LILACS), Brazilian Bibliography of Dentistry (BBO) databases from Latin-American and Caribbean System on Health Sciences Information (BIREME) and PubMed/Medline (US National Library of Medicine - National Institutes of Health) databases were searched regardless of language. Altogether, 1146 in vitro studies were selected. Two reviewers independently selected and assessed the articles according to pre-established inclusion/exclusion criteria. Among all the properties investigated, only one study was classified as being of fair quality that tested compressive strength and was included. It was observed that many authors had not strictly followed ISO recommendations and that, for some properties (diametral tensile strength and microhardness), there are no guidelines provided. CONCLUSIONS: It was not possible to compare the results for the mechanical and optical properties of conventional restorative GICs due to the lack of standardization of studies.

Effects of the reinforced cellulose nanocrystals on glass-ionomer cements.

OBJECTIVE: Glass-ionomer cements (GICs) modified with cellulose nanocrystals (CNs) were characterized and evaluated for compressive strength (CS), diametral tensile strength (DTS) and fluoride release (F-). METHODS: Commercially available GICs (Maxxion, Vidrion R, Vitro Molar, Ketac Molar Easy Mix and Fuji Gold Label 9) were reinforced with CNs (0.2% by weight). The microstructure of CNs and of CN-modified GICs were evaluated by transmission electron microscopy (TEM) and by scanning electron microscopy (SEM) while chemical characterization was by Fourier transform infrared spectroscopy (FTIR). Ten specimens each of the unmodified (control) and CN-modified materials (test materials) were prepared for CS and DTS testing. For the fluoride release evaluation, separate specimens (n=10) of each test and control material were made. The results obtained were submitted to the t-test (p<0.05). RESULTS: The CN reinforcement significantly improved the mechanical properties and significantly increased the F- release of all GICs (p<0.05). The GICs with CNs showed a fibrillar aggregate of nanoparticles interspersed in the matrix. The compounds with CNs showed a higher amount of C compared to the controls due to the organic nature of the CNs. It was not possible to identify by FTIR any chemical bond difference in the compounds formed when nanofibers were inserted in the GICs. SIGNIFICANCE: Modification of GICs with CNs appears to produce promising restorative materials.