Fabrication of Porous Polyimide Membrane with Through-Hole via Multiple Solvent Displacement Method.

Porous polyimide (PI) membranes are widely used in separation processes because of their excellent thermal and mechanical properties. However, the applications of porous PI membranes are limited in the nanofiltration range. In this study, porous PI membranes with through-holes have been successfully fabricated by the novel multiple solvent displacement method. This new method requires only a porous polyamic acid (PAA) membrane, which was prepared by immersing PAA film in N-methylpyrrolidoneebk; (NMP) prior to immersing it in a mixed solvent consisting of NMP and a poor solvent, followed by immersion only in poor solvent. The pore size, morphology, porosity, and air permeability demonstrated that the fabricated PI membranes had a uniformly porous structure with through-holes over their surface. This new method enabled control of pore size (3-11 µm) by selecting a suitable poor solvent. This multiple solvent displacement method is highly versatile and promising for the fabrication of porous PI membranes.

Effects of a Twin-Screw Extruder Equipped with a Molten Resin Reservoir on the Mechanical Properties and Microstructure of Recycled Waste Plastic Polyethylene Pellet Moldings.

Each year, increasing amounts of plastic waste are generated, causing environmental pollution and resource loss. Recycling is a solution, but recycled plastics often have inferior mechanical properties to virgin plastics. However, studies have shown that holding polymers in the melt state before extrusion can restore the mechanical properties; thus, we propose a twin-screw extruder with a molten resin reservoir (MSR), a cavity between the screw zone and twin-screw extruder discharge, which retains molten polymer after mixing in the twin-screw zone, thus influencing the polymer properties. Re-extruded recycled polyethylene (RPE) pellets were produced, and the tensile properties and microstructure of virgin polyethylene (PE), unextruded RPE, and re-extruded RPE moldings prepared with and without the MSR were evaluated. Crucially, the elongation at break of the MSR-extruded RPE molding was seven times higher than that of the original RPE molding, and the Young's modulus of the MSR-extruded RPE molding was comparable to that of the virgin PE molding. Both the MSR-extruded RPE and virgin PE moldings contained similar striped lamellae. Thus, MSR re-extrusion improved the mechanical performance of recycled polymers by optimizing the microstructure. The use of MSRs will facilitate the reuse of waste plastics as value-added materials having a wide range of industrial applications.

Enhancement of the Surface Properties on Polypropylene Film Using Side-Chain Crystalline Block Copolymers.

The consumption of polypropylene (PP) has significantly increased over that of other materials because of its light weight, easy molding, and high mechanical strength. However, the applications of PP are limited, owing to the lack of surface properties, especially with respect to adhesive properties and hydrophilicity. In this study, we developed a surface modification method for enhancing the adhesive properties and hydrophilicity on the PP surface using a side-chain crystalline block copolymer (SCCBC). This method was simple and involved the dipping of a PP film in a diluted SCCBC solution. The optimized modification conditions for enhancing the adhesive properties of PP were investigated. The results revealed that the adhesion strength of PP modified with the SCCBC of behenyl acrylate and 2-(tert-butylamino)ethyl methacrylate was enhanced to 2.00 N/mm (T-peel test) and 1.05 N/mm2 (tensile shear test). In addition, the hydrophilicity of PP modified with the SCCBC of behenyl acrylate and di(ethylene glycol)ethyl ether acrylate was enhanced to a water contact angle of 69 ± 4°. Surface analysis was also performed to elucidate a plausible mechanism for PP modification by the SCCBCs. This surface modification method is facile and enhances desirable properties for the wide application of PP.

Fabrication and evaluation of nanocellulose sponge for oil/water separation.

Nanocellulose sponge was fabricated by a facile method: freeze-drying of nanocellulose aqueous suspension to sponge state, following by hydrophobic treatment with stearoyl chloride at 50 °C for 1 h. The obtained nanocellulose sponge showed superhydrophobicity (160° of water contact angle) and superoleophilicity with high protection from water but selective absorption of oil. Its absorption capacities for various kinds of oil and non-polar liquids were 25-55 times higher than its dry weight and exhibited excellent selectivity for absorbing of oil which spilled on the surface of water or underwater with high separation efficiency. This superhydrophobic nanocellulose sponge can be easily recovered by simple squeezing and reused at least 10 cycles with remained high separation efficiency. It is expected that such a biodegradable nanocellulose sponge can be applied to solve the oil spill accident and treat the oily wastewater from households and industries.

Preparing hydrophobic nanocellulose-silica film by a facile one-pot method.

Hydrophobic nanocellulose-silica film was successfully prepared by a facile one-pot method using tetraethoxysilane (TEOS) and dodecyl triethoxylsilane (DTES). Morphological characterization of the hydrophobic nanocellulose-silica (NC-SiO2-DTES) film showed well self-assembled DTES modified silica spherical nanoparticles with the particle sizes in the range of 88-126nm over the nanocellulose film. The hydrophobicity of the NC-SiO2-DTES film was achieved owing to the improvement of roughness of the nanocellulose film by coating dodecyl- terminated silica nanoparticles. An increase in DTES loading amount and reaction time increased the hydrophobicity of the film, and the optimum condition for NC-SiO2-DTES film preparation was achieved at DTES/TEOS molar ratio of 2.0 for 8h reaction time. Besides, the NC-SiO2-DTES film performed superoleophilic property with octane and hexadecane contact angles of 0°. It also showed an excellent hydrophobic property over all pH values ranged from 1 to 14.