Three-dimensional airway changes after adenotonsillectomy in children with obstructive apnea: Do expectations meet reality?

INTRODUCTION: The assessment of the volumetric changes of the airways after adenotonsillectomy has gained popularity among orthodontists, but the validity of such evaluation is not clear. METHODS: Thirty patients with obstructive sleep apnea diagnosed with the use of polysomnography (PSG) were evaluated according to the Apnea and Hypopnea Index (AHI), the obstructive apnea index (OAI), the oxygen desaturation index (ODI), the lowest oxygen saturation (LSpO2), and the average oxygen saturation (ASpO2). The volume and the minimal cross-section of lower (oropharynx and velopharynx) and upper (nasopharynx) spaces of the airways were calculated. Patients were adenotonsillectomized; posttreatment data were collected after 12 months. Thirty comparison patients also had the volume of airways evaluated. RESULTS: A statistically significant improvement (P < 0.05) of most PSG parameters was observed after adenotonsillectomy: AHI from 14.5 to 5.2, OAI from 9.4 to 5.5, ODI from 14.6 to 6.5, and LSpO2 from 77% to 94%). A significant increase in airway volume of the lower space (from 2571.5 mm3 to 5276.3 mm3) and the upper space (from 726 mm3 to 1056.9 mm3), as well as in the minimal cross-section of the airways (from 98.5 mm2 to 335.8 mm2) was found in adenotonsillectomy patients. No significant volumetric changes of the airways were observed in the comparison patients. No significant correlation was found between PSG parameters and the dimensions of the airways before adenotonsillectomy. No significant correlation was found between changes of the PSG parameters and changes of the dimensions of the airways 12 months after the adenotonsillectomy. CONCLUSIONS: Adenotonsillectomy contributed to the increase of the airway volume and minimal cross-section, and to the improvement of the PSG parameters, but there was no correlation between the magnitude of the anatomic changes and the improvement of the breathing mode.

Tear Strength Analysis of MDX4-4210 and A-2186 Silicones with Different Intrinsic Pigments Incorporated by Mechanical and Industrial Methods.

OBJECTIVE: The aim of this study was to evaluate the tear strength of MDX4-4210 and A-2186 silicones with different intrinsic pigments incorporated by mechanical and industrial methods, comparing nonaged and aged groups. MATERIALS AND METHODS: Twenty-four groups were created according to the American Society for Testing and Materials D-624/type C, half nonaged and half aged (n = 10): bronze mechanical MDX4-4210, bronze industrial MDX4-4210, black mechanical MDX4-4210, black industrial MDX4-4210, pink mechanical MDX4-4210, pink industrial MDX4-4210, bronze mechanical A-2186, bronze industrial A-2186, black mechanical A-2186, black industrial A-2186, pink mechanical A-2186, and pink industrial A-2186. All specimens were submitted to tear strength analysis. Data were submitted to the ANOVA and Tukey test (p < 0.05). RESULTS: An increase in the tear strength values was observed only for the bronze and black MDX4-4210, comparing nonaged and aged silicones (p < 0.05), regardless of the manufacturing method. There was a difference in all comparisons between MDX4-4210 and A-2186 silicones with the same pigment type (p < 0.05), regardless of the manufacturing method. In all cases, there was no difference in the manufacturing method comparing the MDX4-4210 or A-2186 groups with the same pigment. CONCLUSION: Accelerated aging did not influence the tear strength in all aged A-2186 silicones and in aged pink industrial and mechanical MDX4-4210 silicones. The other MDX4-4210 groups had an increase in the results after aging. In all cases compared, the A-2186 groups had higher tear strength values than the MDX4-4210 groups. Mechanical and industrial methods can be used for silicone preparation, without changing the tear strength.