Classification of Corrosion Severity in SPCC Steels Using Eddy Current Testing and Supervised Machine Learning Models.

Steel Plate Cold-Rolled Commercial (SPCC) steel is known to have long-term durability. However, it still undergoes corrosion when exposed to corrosive environments. This paper proposes an evaluation method for assessing the corrosion level of SPCC steel samples using eddy current testing (ECT), along with two different machine learning approaches. The objective is to classify the corrosion of the samples into two states: a less corroded state (state-1) and a highly corroded state (state-2). Generative and discriminative models were implemented for classification. The generative classifier was based on the Gaussian mixture model (GMM), while the discriminative model was based on the logistic regression model. The features used in the classification models are the peaks of the perturbated magnetic fields at two different frequencies. The performance of the classifiers was evaluated using metrics such as absolute error, accuracy, precision, recall, and F1 score. The results indicate that the GMM model is more conducive to categorizing states with higher levels of corrosion, while the logistic regression model is helpful in estimating states with lower levels of corrosion. Meanwhile, high classification accuracy can be achieved based on both methods using eddy current testing.

Baseline-Free Damage Imaging of Composite Lap Joint via Parallel Array of Piezoelectric Sensors.

This paper presents a baseline-free damage imaging technique using a parallel array of piezoelectric sensors and a control board that facilitates custom combinations of sensor selection. This technique incorporates an imaging algorithm that uses parallel beams for generation and reception of ultrasonic guided waves in a pitch-catch configuration. A baseline-free reconstruction algorithm for probabilistic inspection of defects (RAPID) algorithm is adopted. The proposed RAPID method replaces the conventional approach of using signal difference coefficients with the maximum signal envelope as a damage index, ensuring independence from baseline data. Additionally, conversely to the conventional RAPID algorithm which uses all possible sensor combinations, an innovative selection of combinations is proposed to mitigate attenuation effects. The proposed method is designed for the inspection of lap joints. Experimental measurements were carried out on a composite lap joint, which featured two dissimilar-sized disbonds positioned at the lap joint's borderline. A 2D correlation coefficient was used to quantitatively determine the similarity between the obtained images and a reference image with correct defect shapes and locations. The results demonstrate the effectiveness of the proposed damage imaging method in detecting both defects. Additionally, parametric studies were conducted to illustrate how various parameters influence the accuracy of the obtained imaging results.

Locating and Imaging Fiber Breaks in CFRP Using Guided Wave Tomography and Eddy Current Testing.

In this paper, guided Lamb wave tomography and eddy current testing (ECT) techniques were combined to locate and evaluate fiber breaks in carbon-fiber-reinforced plastic (CFRP) structures. Guided wave testing (GWT) and computed tomography (CT) imaging were employed to quickly locate fiber breaks in the CFRP plate. From B-scans performed along two different fiber orientations (0 and 90 degrees), parallel-beam projections of different features were extracted from the guided wave signals, using signal-processing techniques (such as wavelet and Hilbert transforms) and statistical functions (such as skewness and kurtosis). The parallel-beam projections of each individual feature were used as input in computed tomography imaging reconstruction to approximately estimate the location of fiber breaks. From the obtained reconstructed images, image-fusion techniques were applied to get complementary information from multiple source images into one single image. After locating the fiber breaks, C-scans were performed in the vicinity of the damage, using an ECT probe with double excitation configuration to evaluate the condition of the fiber break.

Therapeutic Textiles Functionalized with Keratin-Based Particles Encapsulating Terbinafine for the Treatment of Onychomycosis.

Onychomycosis is the most common nail fungal infection worldwide. There are several therapy options available for onychomycosis, such as oral antifungals, topicals, and physical treatments. Terbinafine is in the frontline for the treatment of onychomycosis; however, several adverse effects are associated to its oral administration. In this work, innovative keratin-based carriers encapsulating terbinafine were designed to overcome the drawbacks related to the use this drug. Therapeutic textiles functionalized with keratin-based particles (100% keratin; 80% keratin/20% keratin-PEG) encapsulating terbinafine were developed. The controlled release of terbinafine from the functionalized textiles was evaluated against different mimetic biologic solutions (PBS buffer-pH = 7.4, micellar solution and acidic sweat solution-pH = 4.3). The modification of keratin with polyethylene glycol (PEG) moieties favored the release of terbinafine at the end of 48 h for all the solution conditions. When the activity of functionalized textiles was tested against Trichophyton rubrum, a differentiated inhibition was observed. Textiles functionalized with 80% keratin/20% keratin-PEG encapsulating terbinafine showed a 2-fold inhibition halo compared with the textiles containing 100% keratin-encapsulating terbinafine. No activity was observed for the textiles functionalized with keratin-based particles without terbinafine. The systems herein developed revealed therapeutic potential towards nail fungal infections, taking advantage of keratin-based particles affinity to keratin structures and of the keratinase activity of T. rubrum.

Biotechnological applications of mammalian odorant-binding proteins.

The olfactory system of mammals allows the detection and discrimination of thousands of odors from the environment. In mammals, odorant-binding proteins (OBPs) are considered responsible to carry odorant molecules across the aqueous nasal mucus to the olfactory receptors (ORs). The three-dimensional structure of these proteins presents eight antiparallel ß-sheets and a short α-helical segment close to the C terminus, typical of the lipocalins family. The great ability of OBPs to bind differentiated ligand molecules has driven the research to understand the mechanisms underlying the OBP function in nature and the development of advanced biotechnological applications. This review describes the role of mammalian OBPs in the olfactory perception, highlighting the influence of several key parameters (amino acids, temperature, ionic strength, and pH) in the formation of the OBP/ligand complex. The information from the literature regarding OBP structure, affinity, the strength of binding, and stability inspiring the development of several applications herein detailed.

Development of Capacitive-Type Sensors by Electrochemical Anodization: Humidity and Touch Sensing Applications.

This work describes the development of a capacitive-type sensor created from nanoporous anodic aluminium oxide (NP-AAO) prepared by the one-step anodization method conducted in potentiostatic mode and performed in a low-cost homemade system. A series of samples were prepared via an anodization campaign carried out on different acid electrolytes, in which the anodization parameters were adjusted to investigate the effect of pore size and porosity on the capacitive sensing performance. Two sensor test cases are investigated. The first case explores the use of highly uniform NP-AAO structures for humidity sensing applications while the second analyses the use of NP-AAO as a capacitive touch sensor for biological applications, namely, to detect the presence of small "objects" such as bacterial colonies of Escherichia Coli. A mathematical model based on equivalent electrical circuits was developed to evaluate the effect of humidity condensation (inside the pores) on the sensor capacitance and also to estimate the capacitance change of the sensor due to pore blocking by the presence of a certain number of bacterial microorganisms. Regarding the humidity sensing test cases, it was found that the sensitivity of the sensor fabricated in a phosphoric acid solution reaches up to 39 (pF/RH%), which is almost three times higher than the sensor fabricated in oxalic acid and about eight times higher than the sensor fabricated in sulfuric acid. Its improved sensitivity is explained in terms of the pore size effect on the mean free path and the loss of Brownian energy of the water vapour molecules. Concerning the touch sensing test case, it is demonstrated that the NP-AAO structures can be used as capacitive touch sensors because the magnitude of the capacitance change directly depends on the number of bacteria that cover the nanopores; the fraction of the electrode area activated by bacterial pore blocking is about 4.4% and 30.2% for B1 (E. Coli OD600nm = 0.1) and B2 (E. Coli OD600nm = 1) sensors, respectively.

Comparison of Inspecting Non-Ferromagnetic and Ferromagnetic Metals Using Velocity Induced Eddy Current Probe.

A velocity induced eddy current probe has been used to detect cracks in both non-ferromagnetic and ferromagnetic metals. The simulation and experimental results show that this probe can successfully detect cracks in both cases, but further investigation shows that the underlying principles for inspecting non-ferromagnetic and ferromagnetic metals are actually different. For an aluminum plate, the induced eddy current density and the signal amplitude both increase with probe speed, which means the signal is caused by velocity induced eddy currents. For a steel plate, probe speed changes the baselines of the testing signals; however, it has little influence on signal amplitudes. Simulation results show that the signal for cracks in a steel plate is mainly caused by direct magnetic field perturbation rather than velocity induced eddy currents.

Therapeutic l-asparaginase: upstream, downstream and beyond.

l-asparaginase (l-asparagine amino hydrolase, E.C.3.5.1.1) is an enzyme clinically accepted as an antitumor agent to treat acute lymphoblastic leukemia and lymphosarcoma. It catalyzes l-asparagine (Asn) hydrolysis to l-aspartate and ammonia, and Asn effective depletion results in cytotoxicity to leukemic cells. Microbial l-asparaginase (ASNase) production has attracted considerable attention owing to its cost effectiveness and eco-friendliness. The focus of this review is to provide a thorough review on microbial ASNase production, with special emphasis to microbial producers, conditions of enzyme production, protein engineering, downstream processes, biochemical characteristics, enzyme stability, bioavailability, toxicity and allergy potential. Some issues are also highlighted that will have to be addressed to achieve better therapeutic results and less side effects of ASNase use in cancer treatment: (a) search for new sources of this enzyme to increase its availability as a drug; (b) production of new ASNases with improved pharmacodynamics, pharmacokinetics and toxicological profiles, and (c) improvement of ASNase production by recombinant microorganisms. In this regard, rational protein engineering, directed mutagenesis, metabolic flux analysis and optimization of purification protocols are expected to play a paramount role in the near future.

Albumin/asparaginase capsules prepared by ultrasound to retain ammonia.

Asparaginase reduces the levels of asparagine in blood, which is an essential amino acid for the proliferation of lymphoblastic malign cells. Asparaginase converts asparagine into aspartic acid and ammonia. The accumulation of ammonia in the bloodstream leads to hyperammonemia, described as one of the most significant side effects of asparaginase therapy. Therefore, there is a need for asparaginase formulations with the potential to reduce hyperammonemia. We incorporated 2 % of therapeutic enzyme in albumin-based capsules. The presence of asparaginase in the interface of bovine serum albumin (BSA) capsules showed the ability to hydrolyze the asparagine and retain the forming ammonia at the surface of the capsules. The incorporation of Poloxamer 407 in the capsule formulation further increased the ratio aspartic acid/ammonia from 1.92 to 2.46 (and 1.10 from the free enzyme), decreasing the levels of free ammonia. This capacity to retain ammonia can be due to electrostatic interactions and retention of ammonia at the surface of the capsules. The developed BSA/asparaginase capsules did not cause significant cytotoxic effect on mouse leukemic macrophage cell line RAW 264.7. The new BSA/asparaginase capsules could potentially be used in the treatment of acute lymphoblastic leukemia preventing hyperammonemia associated with acute lymphoblastic leukemia (ALL) treatment with asparaginase.

Development of elastin-like recombinamer films with antimicrobial activity.

In the present work we explored the ABP-CM4 peptide properties from Bombyx mori for the creation of biopolymers with broad antimicrobial activity. An antimicrobial recombinant protein-based polymer (rPBP) was designed by cloning the DNA sequence coding for ABP-CM4 in frame with the N-terminus of the elastin-like recombinamer consisting of 200 repetitions of the pentamer VPAVG, here named A200. The new rPBP, named CM4-A200, was purified via a simplified nonchromatographic method, making use of the thermoresponsive behavior of the A200 polymer. ABP-CM4 peptide was also purified through the incorporation of a formic acid cleavage site between the peptide and the A200 sequence. In soluble state the antimicrobial activity of both CM4-A200 polymer and ABP-CM4 peptide was poorly effective. However, when the CM4-A200 polymer was processed into free-standing films high antimicrobial activity against Gram-positive and Gram-negative bacteria, yeasts and filamentous fungi was observed. The antimicrobial activity of CM4-A200 was dependent on the physical contact of cells with the film surface. Furthermore, CM4-A200 films did not reveal a cytotoxic effect against both normal human skin fibroblasts and human keratinocytes. Finally, we have developed an optimized ex vivo assay with pig skin demonstrating the antimicrobial properties of the CM4-A200 cast films for skin applications.

Enzymatic synthesis of poly(catechin)-antibiotic conjugates: an antimicrobial approach for indwelling catheters.

Biofilm formation in urinary indwelling catheters is one of the most critical issues that patients face. Catheters were coated with poly(catechin)-antibiotic conjugates with enhanced antimicrobial properties. Catechin was conjugated with two antibiotics, namely trimethoprim (TMP) and sulfamethoxazole (SMZ) via activation with N,N'-disuccinimidyl carbonate (DSC) and subsequent coupling to molecules containing α-amine moieties. Silicone and polyurethane catheters were functionalized in situ through laccase oxidation of catechin-antibiotic conjugates. Four antimicrobial coatings were produced, namely with poly(catechin), poly(catechin)-TMP, poly(catechin)-SMZ and poly(catechin)-TMP-SMZ. The bacterial adhesion reduction was tested on the functionalized devices using gram-negative and gram-positive strains. The most significant reduction in adhesion was observed with poly(catechin)-TMP (gram-negative -85 % and gram-positive -87 %) and with poly(catechin)-TMP-SMZ (gram-negative -85 % and gram-positive -91 %). The cytotoxicity to mammalian cells was tested by indirect contact for 5 days and revealed that all the tested coatings supported more than 90 % of viable cells. A promising approach for the increase of the indwelling catheter lifespan was developed aiming to reduce catheter-associated chronic infections.

An Unusual Coexistence: Right-Sided Colon Cancer and Intestinal Malrotation in an Adult.

Intestinal malrotation (IM), a rare congenital anomaly disrupting typical embryonic rotation around the superior mesenteric artery, is exceptionally uncommon in adults, with its link to colon cancer being even rarer. This article presents a case of colonic cancer in conjunction with IM in a 63-year-old male. Image studies and intraoperative findings show signs of IM. Open resection was performed due to concerns about vascular anomalies and abnormal lymphatic drainage. The case underscores the rarity of colon cancer in a malrotated gut, highlighting the necessity of preoperative identification for precise surgical planning and emphasizing the importance of careful dissection to prevent inadvertent vascular injury.

Adhesive Porosity Analysis of Composite Adhesive Joints Using Ultrasonic Guided Waves.

Adhesively bonded composite joints can develop voids and porosity during fabrication, leading to stress concentration and a reduced load-carrying capacity. Hence, adhesive porosity analysis during the fabrication is crucial to ensure the required quality and reliability. Ultrasonic-guided wave (UGW)-based techniques without advanced signal processing often provide low-resolution imaging and can be ineffective for detecting small-size defects. This article proposes a damage imaging process for adhesive porosity analysis of bonded composite plates using UGWs measured by scanning laser Doppler vibrometer (LDV). To implement this approach, a piezoelectric transducer is mounted on the composite joint specimen to generate UGWs, which are measured over a densely sampled area. The signals obtained from the scan are processed using the proposed signal processing in different domains. Through the utilization of filter banks in frequency and wavenumber domains, along with the root-mean-square calculation of filtered signals, damage images of the adhesive region are obtained. It has been observed that different filters provide information related to different void sizes. Combining all the images reconstructed by filters, a final image is obtained which contains damages of various sizes. The images obtained by the proposed method are verified by radiography results and the porosity analysis is presented. The results indicate that the proposed methodology can detect the pores with the smallest detectable pore area of 2.41 mm2, corresponding to a radius of 0.88 mm, with an overall tendency to overestimate the pore size by an average of 11%.

Development and Evaluation of Microencapsulated Oregano Essential Oil as an Alternative Treatment for Candida albicans Infections.

Vulvovaginal candidiasis (VVC) is characterized as a very common fungal infection that significantly affects women's health worldwide. Essential oils (EOs) are currently being evaluated as an alternative therapy. The development of efficient techniques such as micro- or nanoencapsulation for protecting and controlling release is essential to overcome the limitations of EO applications. Therefore, the aim of this study was to develop and characterize oregano EO-loaded keratin microparticles (OEO-KMPs) as a potential treatment for VVC. OEO-KMPs were produced using high-intensity ultrasonic cycles and characterized in terms of morphological and physicochemical parameters. In vitro evaluation included assessing the toxicity of the OEO-KMPs and their effect against Candida albicans using microdilution and agar diffusion, while the activity against biofilm was quantified using colony forming units (CFU). The efficacy of the OEO-KMPs in an in vivo VVC mouse model was also studied. Female BALB/c mice were intravaginally infected with C. albicans, 24 h postinfection animals were treated intravaginally with 15 µL of OEO-KMPs and 24 h later vaginal fluid was analyzed for C. albicans and Lactobacillus growth (CFU mL-1). The results showed the stability of the OEO-KMPs over time, with high encapsulation efficiency and controlled release. This nanoparticle size facilitated penetration and completely inhibited the planktonic growth of C. albicans. In addition, an in vitro application of 2.5% of the OEO-KMPs eradicated mature C. albicans biofilms while preserving Lactobacillus species. In in vivo, a single intravaginal application of OEO-KMPs induced a reduction in C. albicans growth, while maintaining Lactobacillus species. In conclusion, this therapeutic approach with OEO-KMPs is promising as a potential alternative or complementary therapy for VVC while preserving vaginal microflora.

Sodium alginate-based multifunctional sandwich-like system for treating wound infections.

Microbial colonization and development of infections in wounds is a sign of chronicity. The prevailing approach to manage and treat these wounds involves dressings. However, these often fail in effectively addressing infections, as they struggle to both absorb exudates and maintain optimal local moisture. The system here presented was conceptualized with a three-layer design: the outer layer made of a fibrous polycaprolactone (PCL) film, to act as a barrier for preventing microorganisms and impurities from reaching the wound; the intermediate layer formed of a sodium alginate (SA) hydrogel loaded with ampicillin (Amp) for fighting infections; and the inner layer comprised of a fibrous film of PCL and polyethylene glycol (PEG) for facilitating cell recognition and preventing wound adhesion. Thermal evaluations, degradation, wettability and release behavior testing confirmed the system resistance overtime. The sandwich demonstrated the capability for absorbing exudates (≈70 %) and exhibited a controlled release of Amp for up to 24 h. Antimicrobial testing was performed against Staphylococcus aureus and Escherichia coli, as representatives of Gram-positive and Gram-negative bacteria: >99 % elimination of bacteria. Cell cytotoxicity assessments showed high cytocompatibility levels, confirming the safety of the proposed sandwich system. Adhesion assays confirmed the system ease of detaching without mechanical effort (0.37 N). Data established the efficiency of the sandwich-like system, suggesting promising applications in infected wound care.

Nanostructured Lipid Carriers Enriched Hydrogels for Skin Topical Administration of Quercetin and Omega-3 Fatty Acid.

Chronic skin exposure to external hostile agents (e.g., UV radiation, microorganisms, and oxidizing chemicals) may increase oxidative stress, causing skin damage and aging. Because of their well-known skincare and protective benefits, quercetin (Q) and omega-3 fatty acids (ω3) have attracted the attention of the dermocosmetic and pharmaceutical sectors. However, both bioactives have inherent properties that limit their efficient skin delivery. Therefore, nanostructured lipid carriers (NLCs) and enriched PFC® hydrogels (HGs) have been developed as a dual-approach vehicle for Q and/or ω3 skin topical administration to improve bioactives' stability and skin permeation. Two NLC formulations were prepared with the same lipid composition but differing in surfactant composition (NLC1-soy lecithin and poloxamer 407; NLC2-Tween® 80 and dioctyl sodium sulfosuccinate (DOSS)), which have an impact on physicochemical properties and pharmaceutical and therapeutic performance. Despite both NLCs presenting high Q loading capacity, NLC2's physicochemical properties make them more suitable for topical skin administration and ensure longer colloidal stability. Additionally, NLC2 demonstrated a more sustained Q release, indicating higher bioactive storage while improving permeability. The occlusive effect of NLCs-enriched HGs also has a positive impact on skin permeability. Q-loaded NLC2, with or without ω3, -enriched HGs demonstrated efficacy as antioxidant and photoprotective formulations as well as effective reduction in S. aureus growth, indicating that they constitute a promising approach for topical skin administration to prevent skin aging and other damaging cutaneous processes.

Research Note: Nitrogen-corrected apparent metabolizable energy and standardized ileal amino acid digestibility determination of high-protein dried distiller's grains and corn bran with solubles for broilers.

Metabolism and digestibility trials were performed on broiler chickens to determine 1) nitrogen-corrected apparent metabolizable energy (AMEn) using total excreta collection and 2) standardized ileal amino acid digestibility (SIAAD) using the ileal digesta collection from high-protein dried distillers' grains (HP-DDG) and corn bran with solubles (CBS). The results of the metabolism trial indicated that AMEn values for HP-DDG and CBS were 3,334 kcal/kg and 2,083 kcal/kg on dry matter (DM) basis, respectively. Concerning the HP-DDG, the digestibility trial resulted in the following SIAAD values and digestible concentrations, respectively: 80.33% and 1.09 for Lys, 85.95% and 1.44 for Met + Cys, 75.58% and 1.24 for Thr, 89.58% and 1.66 for Arg, 84.91% and 1.08 for His, 86.37% and 1.35 for Ile, 90.64% and 4.56 for Leu, 85.76% and 1.80 for Val, and 88.67% and 1.90 for Phe. Concerning the CBS, the following SIAAD values and digestible concentrations were measured, respectively: 79.29% and 0.44 for Lys, 89.57% and 0.31 for Met + Cys, 78.89% and 0.40 for Thr, 92.28% and 0.66 for Arg, 87.48% and 0.36 for His, 93.40% and 0.35 for Ile, 92.27% and 1.01 for Leu, 90.97% and 0.51 for Val, and 88.81% and 0.45 for Phe. The digestibility average of CBS is 88.45% for essential amino acids and 85.21% for nonessential amino acids, whereas the digestibility average of HP-DDG is 85.83% for essential amino acids and 83.83% for nonessential amino acids.

Research Note: The influence of different isoleucine: lysine ratios on the growth performance of broiler chickens fed low-protein diets.

Two trials were carried out to assess the effects of different ratios of standardized ileal digestible isoleucine:lysine (SID Ile:Lys) on the growth performance of broiler chickens fed low-protein diets. A total of 1,320 male chickens were distributed in each trial into 6 treatments, with 10 replicates with 22 birds each. A control diet was formulated that satisfied the nutritional requirements of the broilers, and a low-protein diet was formulated with reduced protein content, meeting broiler nutritional requirements, except for the SID Ile levels. Five SID Ile:Lys ratios (56%, 61%, 66%, 71%, and 76%) were obtained by adding l-isoleucine to the low-protein diet. The body weight (BW), body weight gain (BWG), average daily feed intake (ADFI), and feed conversion ratio (FCR) were evaluated from day 1 to day 21 in trial 1, and from day 22 to day 44 in trial 2. ANOVA was performed on the data, and the treatments were compared to the control group using Dunnett's test (P ≤ 0.05). Regression analyses were performed for modeling the variables assessed and the ratios of SID Ile:Lys. There was no significant difference between the treatments on ADFI of birds (P > 0.05). The BW, BWG, and FCR showed a quadratic effect as the SID Ile:Lys ratio increased in low-protein diets in trials 1 and 2 (P ≤ 0.05). In conclusion, the recommended ratio of SID Ile:Lys in low-protein diets for growth performance is around 66% for broiler chickens from 1 to 21 d old and is around 65% for broiler chickens from 22 to 44 d old.

Starch-based films doped with porphyrinoid photosensitizers for active skin wound healing.

Starch is a biodegradable and biocompatible carbohydrate that, when combined with bioactive molecules, can be processed as biomimetic platforms with enhanced performance, allowing its use as active wound dressing materials. Porphyrinoid photosensitizers can tune the physicochemical/functional profile of biomacromolecules, allowing their use in anti-infective strategies. In this work, the feasibility of using the cationic 5,10,15,20-tetrakis(1-methylpyridinium-4-yl)porphyrin tetraiodide (TMPyP) to enhance the physicochemical, mechanical, antimicrobial performance, and wound healing ability of casted starch-based films was studied. TMPyP conferred a reddish coloration to the films, maintaining their pristine transparency. It increased by 87 % the films hydrophobicity and, depending on the TMPyP used, conferred mobility to the starch polymeric chains. Starch/TMPyP-based films effectively photoinactivated Escherichia coli (>99.99 %) and favored the wound healing process, even in the absence of light. Therefore, the incorporation of TMPyP into starch-based formulations revealed to be a promising strategy to tune the films compaction degree while giving rise to water tolerant and photosensitive biomaterials that can act as multitarget antimicrobial medical dressings and glycocarriers of active compounds relevant for effective skin wound healing.

TNF-α modulates statin effects on secretion and expression of MCP-1, PAI-1 and adiponectin in 3T3-L1 differentiated adipocytes.

PURPOSE: Systemic inflammatory conditions, as seen in obesity and in the metabolic syndrome, are associated with high plasmatic levels of proatherogenic and prothromboticadipokines and low levels of adiponectin. Inhibitors of HMG-CoA reductase have beneficial effects in reducing cardiovascular events attributed predominantly to its lipid-lowering effects and recent studies suggest that these effects might be due to its anti-inflammatory properties. Based on the pleiotropic properties of simvastatin we studied the effects of this drug on the secretion and expression of adiponectin, PAI-1 and MCP-1 in mature adipocytes under baseline conditions and after an inflammatory stimulation. MATERIALS AND METHODS: The differentiated adipocytes were incubated with 10 µM simvastatin or vehicle and TNF-α 10 ng/mL or vehicle were added to treatment media. After 24h of incubation, the media was harvested and the proteins of interest were analyzed by Multiplex method. Gene expression was analyzed by real time-PCR. RESULTS: The addition of TNF-α increased the expression and secretion of MCP-1 and PAI-1. However, stimulation did not interfere with the secretion of adiponectin, despite having significantly reduced its expression. Our data also demonstrated that simvastatin reduced the expression and secretion of MCP-1, under baseline (770.4 ± 199.9 vs 312.7 ± 113.7 and 1.00 ± 0.14 vs 0.63 ± 0.13, p<0.05, respectively) and inflammatory conditions (14945 ± 228.7 vs 7837.6 ± 847.4 and 24.16 ± 5.49 vs 14.97 ± 2.67, p<0.05, p<0.05, respectively). Simvastatin also attenuated the increase in expression and secretion of PAI-1 induced by TNF-α (16898.6 ± 1663.3 vs 12922.1 ± 843.9 and 5.19 ± 3.12 vs 0.59 ± 0.16, respectively p<0.05), but under baseline conditions had no effect on the expression or secretion of PAI-1. The statin increased the expression of adiponectin under baseline conditions and inflammatory stimulation (1.03 ± 0.08 vs 4.0 ± 0.96 and 0.77 ± 0.19 vs 2.16 ± 0.23, respectively, p<0.05) and also increased the secretion of this adipokine but only with the inflammatory stimulus (5347.7 ± 1789.3 vs 7327.3 ± 753.6, p<0.05). CONCLUSIONS: Our findings suggested that simvastatin counteracted the stimulatory effect of TNF-α on secretion and expression of MCP-1, PAI-1 and adiponectin, implying a potential anti-atherogenic effect during the inflammatory process; these pleitropic effects were more pronounced with HMG-CoA reductase inhibitor.