Candelilla Wax Extracted by Traditional Method and an Ecofriendly Process: Assessment of Its Chemical, Structural and Thermal Properties.

A comparative study was carried out on the chemical, structural and thermal properties of candelilla wax from four wax-producing communities in Mexico, which was obtained by two extraction processes, the conventional one using sulfuric acid (SA) and an eco-friendly alternative process using citric acid (CA) as the extracting agent. The waxes were analyzed by basic chemistry (acidity, saponification, ester indexes, and others), color, Fourier transform infrared spectroscopy (FTIR), Raman micro-spectroscopy, X-ray diffraction (XRD), differential scanning calorimetry (DSC), and hardness and brittleness measurements. The waxes obtained by the environmentally friendly process showed differences in their physicochemical properties when compared to waxes from the conventional process. In addition, they showed some improvements, such as lighter shades and harder waxes, suggesting that the new environmentally friendly process is a viable option.

Vegetable oils as green solvents for carotenoid extraction from pumpkin (Cucurbita argyrosperma Huber) byproducts: Optimization of extraction parameters.

Pumpkin pulp is the main waste generated by pumpkin seed growers. This agro-industrial waste is a valuable source of bioactive compounds, especially carotenoids (ß-carotene, α-carotene, and lutein), which exhibit a broad spectrum of health-promoting effects. In this study, vegetable oils (canola, corn, and soybean oil) were used as green solvent alternatives to conventional organic solvents for carotenoid extraction from dried pumpkin pulp (DPP) waste. The highest carotenoid extraction yield (CEY) was obtained with canola oil, at a 1:10 DPP/oil ratio. Response surface methodology (RSM) was used to optimize the extraction process parameters (temperature, time, and stirring rate) through a Box-Behnken design (BBD) maximizing CEY in canola oil. The extraction temperature and stirring rate were found to have a significant linear and quadratic effect, respectively, on CEY. Optimum conditions were achieved at 21.8 min, 250 rpm, and 60°C. Under these optimized conditions, the estimated value for CEY was 378.1 µg ß-carotene equivalents/g of DPP, corresponding to 61.6% of the total carotenoid content present in the DPP. In contrast, the observed experimental value was 373.2 µg ß-carotene equivalents/g of DPP (61.2%). The experimental value was very close to the estimated value, which verifies the model's adequacy and fit. This study shows an alternative method to extract carotenoids from DPP with canola oil, obtaining an oil naturally enriched with carotenoids that could be used as a potential functional ingredient in the development of food, cosmetics, and medicinal products. PRACTICAL APPLICATION: Pumpkin by-products are a potential carotenoid source. Vegetable oil can be used as an alternative solvent for carotenoid extraction from pumpkin residues to obtain an enriched carotenoid oil that can be used to formulate food products.

Utilization of Agave durangensis leaves by Bacillus cereus 4N for polyhydroxybutyrate (PHB) biosynthesis.

Lignocellulosic wastes may provide a means to economize polyhydroxybutyrate (PHB) production. This study has proposed the use of Agave durangensis leaves obtained from the artisanal mezcal industry as a novel substrate for this aim. Results revealed an increase in PHB biosynthesis (0.32 g/L) and improvement in %PHB (16.79-19.51%) by Bacillus cereus 4N when A. durangensis leaves used as carbon source were physically pre-treated by ultrasound for 30 min (ADL + US30') and thermally pre-treated (ADL + Q). Chemical analyses and SEM studies revealed compositional and morphological changes when A. durangensis leaves were physically pre-treated. Also, elemental analysis of growth media showed that carbon/nitrogen ratios of 14-21, and low nitrogen, hydrogen, and protein content were well-suited for PHB biosynthesis. Confocal microscopy revealed morphological changes in the bacterial cell and carbonosome structure under the influence of different substrates. Finally, Fourier transform infrared spectroscopy (FTIR) and differential scanning calorimetry (DSC) analyses showed that homopolymeric PHB with a high thermal-resistance (271.94-272.89 °C) was produced. Therefore, the present study demonstrates the potential use of physically pre-treated A. durangensis leaves to produce PHB. These results promote the development of a circular economy in Mexico, where lignocellulosic wastes can be employed to produce value-added biotechnological products.

Efficient recovery of thermostable polyhydroxybutyrate (PHB) by a rapid and solvent-free extraction protocol assisted by ultrasound.

Nowadays, there are great research interest in polyhydroxybutyrate (PHB) recovery protocols that reduce the use of organic solvents and efficiently recover this bacterial biopolymer. The present study reports an extraction protocol assisted by ultrasound, which is a rapid protocol that increases the amount of polymeric matter extracted, reduces the cellular digestion step with sodium hypochlorite and eliminates the use of organic solvents. Likewise, characterization studies by Fourier transform infrared spectroscopy (FTIR), proton nuclear magnetic resonance spectroscopy (1H NMR), differential scanning calorimetry (DSC), and X-ray diffraction (XRD) demonstrated that the biopolymer recovered by this protocol is PHB homopolymer with a major thermal-resistance and crystalline properties. Besides, in this study are reported the thermic and crystalline differences between the PHB obtained from the fermentation of complex carbohydrates (agavins) and simple sugars. The biopolymer obtained by this rapid extraction protocol would be suitable for ecological and biomedical applications, due to the low melting temperature, less than 50% crystallinity, and the lack of lipopolysaccharides. Therefore, this extraction protocol might represent an alternative to the traditional protocol based on NaOCl-chloroform and is part of the green trend to improve the PHB production.

Changes in the microstructural, textural, thermal and sensory properties of apple leathers containing added agavins and inulin.

In this study the effect of agavin and inulin addition on the microstructural, textural, thermal and sensory properties of apple leathers was investigated. Agavins and inulin were added to leathers at two concentration levels (6 and 4%) individually and as a mixture. Scanning Electron Microscopy (SEM) revealed more compact and less porous matrices in the 6% concentration with respect to the control, influencing leather texture. In formulations with agavins the texture was significantly (p < 0.05) smoother than in those with inulin. No relationship was found between hardness and glass transition temperature (Tg), but there was a significant difference between treated leathers and the control. The acceptability of the product showed a direct relationship with the hardness. There were significant changes in the leathers after storage. Agavins and inulin exhibited different technological properties and considering the texturising effect of the agavins, their potential for use in the food industry is promising.

Pectin from Husk Tomato (Physalis ixocarpa Brot.): Rheological behavior at different extraction conditions.

A rheological study was carried out to evaluate formulations of test dispersions and gels of high methoxyl pectins (HTHMP) obtained at different conditions from husk tomato waste (Physalis ixocarpa Brot.). The effect of extraction agent (hydrochloric acid or citric acid), blanching time (10 or 15min) and extraction time (15, 20 or 25min) on the rheology of the tested samples was evaluated. Flow behavior and activation energy were evaluated on the test dispersions, while (Ea) frequency sweeps, temperature sweep, creep-recovery test and penetration test were performed on the gels. HTHMP dispersions showed shear thinning flow behavior, while showing a good fit to Cross model. Extraction agent, blanching time and extraction time did not have effect on Cross parameters (ηz, η∞, C, and m). Ea decreased as blanching time and extraction time increased. Frequency sweeps revealed high dependence on frequency for both G' and G", while temperature sweeps (25- 95°C) showed thermostable husk tomato pectin gels. Hydrocloric acid (HCl) extracted pectin gels showed stronger structure than citric acid (CA) gels.

Microencapsulation of Lactobacillus helveticus and Lactobacillus delbrueckii using alginate and gellan gum.

Sodium alginate (SA) at 2% (w/v) and low acylated gellan gum (LAG) at 0.2% (w/v) were used to microencapsulate Lactobacillus helveticus and Lactobacillus delbrueckii spp lactis by employing the internal ionic gelation technique through water-oil emulsions at three different stirring rates: 480, 800 and 1200 rpm. The flow behavior of the biopolymer dispersions, the activation energy of the emulsion, the microencapsulation efficiency, the size distribution, the microcapsules morphology and the effect of the stirring rate on the culture viability were analyzed. All of the dispersions exhibited a non-Newtonian shear-thinning flow behavior because the apparent viscosity decreased in value when the shear rate was increased. The activation energy was calculated using the Arrhenius-like equation; the value obtained for the emulsion was 32.59 kJ/mol. It was observed that at 400 rpm, the microencapsulation efficiency was 92.83%, whereas at 800 and 1200 rpm, the stirring rates reduced the efficiency to 15.83% and 4.56%, respectively, evidencing the sensitivity of the microorganisms to the shear rate (13.36 and 20.05 s(-1)). Both optical and scanning electron microscopy (SEM) showed spherical microcapsules with irregular topography due to the presence of holes on its surface. The obtained size distribution range was modified when the stirring rate was increased. At 400 rpm, bimodal behavior was observed in the range of 20-420 µm; at 800 and 1200 rpm, the behavior became unimodal and the range was from 20 to 200 µm and 20 to 160 µm, respectively.