RESUMO
The synergistic effect among flotation agents is why combined flotation agents exhibit superior performance compared to single flotation agents. This research investigates the influence of three surfactants with different charges of polar groups, sodium dodecyl sulfate (SDS), cetyltrimethylammonium bromide (CTAB), and octanol, combined with dodecylamine (DDA), on quartz flotation. Through the implementation of flotation tests, bubble-particle adhesion induction time testing, gas-liquid two-phase foam properties testing, and surface tension testing, it is revealed that substituting part of the DDA with these surfactants can either enhance or at least maintain the quartz recovery, affect the adhesion induction time, reduce the surface tension of the flotation system, and change the foaming performance and foam stability, depending on their mole ratio in the combined collector. Compared to DDA alone, combining CTAB or OCT with DDA can significantly increase quartz recovery, while SDS with DDA only yields an approximate recovery. Combining SDS or OCT with DDA can reduce the foam stability, while CTAB with DDA enhances the foam stability. The effect of the combination of surfactants and DDA on the adhesion induction time of quartz grains of different sizes with bubbles is the same; furthermore, there is a negative correlation between the adhesion induction time and the recovery, while the foaming properties and stability of foam are positively correlated with the recovery.
RESUMO
The functionalization of noble metals is an effective approach to lowering the sensing temperature and improving the sensitivity of metal oxide semiconductor (MOS)-based gas sensors. However, there is a dearth of comparative analyses regarding the differences in sensitization mechanisms between the two functionalization modes of noble metal loading and doping. In this investigation, we synthesized Pt-doped CuO gas-sensing materials using a one-pot hydrothermal method. And for Pt-loaded CuO, Pt was deposited on the synthesized pristine CuO surface by using a dipping method. We found that both functionalization methods can considerably enhance the response and selectivity of CuO toward NO2 at low temperatures. However, we observed that CuO with Pt loading had superior sensing performance at 25 °C, while CuO with Pt doping showed more substantial response changes with an increase in the operating temperature. This is mainly due to the different dominant roles of electron sensitization and chemical sensitization resulting from the different forms of Pt present in different functionalization modes. For Pt doping, electron sensitization is stronger, and for Pt loading, chemical sensitization is stronger. The results of this study present innovative ideas for understanding the optimization of noble metal functionalization for the gas-sensing performance of metal oxide semiconductors.
RESUMO
Gas sensors require the construction of composites with high reactivity to reduce the detection limit, but this can lead to a broad-spectrum response between the adsorbed oxygen and the target gas, making it difficult to improve selectivity. In this study, the phenomenon of electron polar transport properties of the two-dimensional heterojunction material is first discovered in gas sensing and utilized to greatly improve the selectivity of butanone sensors. Ultra-thin porous ZnO nanosheets modified with SnO2/NiO heterogeneous particles are synthesized to achieve 20 ppb detection limits for butanone with a response of 328 to 100 ppm butanone, which is the lowest known detection limit. The combination of reaction kinetics and liquid chromatography-mass spectrometry reveals a good synergistic catalytic effect of SnO2/NiO heterogeneous particles, which may contribute to the high response and low detection limit of butanone. Finally, the possible mechanism for the generation of electron polar transport phenomenon is analyzed in the two-dimensional heterojunction material. This work provides a novel perspective for achieving both selectivity and detection limits in gas sensors, with universal applicability and application potential.
Assuntos
Elétrons , Óxido de Zinco , Catálise , Transporte de ElétronsRESUMO
The hydrometallurgical recovery of gold from electronic waste and gold slag is a hot research topic. To develop a cost-effective and environmentally friendly adsorbent for gold recovery, four types of amino-acid (arginine, histidine, methionine, and cysteine)-functionalized cellulose microspheres were prepared via a radiation technique. The adsorption performance of the amino acid resins toward Au(III) ions was systematically investigated by batch experiments. The amino acid resins could absorb Au(III) ions at a wide pH range. The adsorption process was followed by the pseudo-second-order model and Langmuir model. The theoretical maximum adsorption capacity was calculated as 396.83 mg/g, 769.23 mg/g, 549.45 mg/g, and 636.94 mg/g for ArgR, HisR, MetR, and CysR, respectively. The amino acid resins could effectively and selectively recover trace Au(III) ions from the leaching solutions of printed circuit board and gold slag waste. Lastly, the mechanism underlying amino acid resin's Au(III) ion recovery capability was investigated by FTIR, XRD, and XPS analyses. This work describes a series of cost-effective gold adsorbents with excellent selectivity and adsorption capacity to boost their practical application.
RESUMO
Detection of flammable, explosive and toxic butyl acetate helps to avoid accidents and protect health in industrial production. However, there are few reports on butyl acetate sensors, especially highly sensitive, low detection limit and highly selective ones. In this work, density functional theory (DFT) analyzes the electronic structure of sensing materials and the adsorption energy of butyl acetate. The effects of Ni element doping, oxygen vacancy constructions, and NiO quantum dot modifications on the modulation of the electronic structure of ZnO and on the adsorption energy of butyl acetate are investigated in detail. Based on the DFT analysis, the NiO quantum dot modified jackfruit-shaped ZnO is synthesized via thermal solvent method reduction. The NiO/ZnO sensor has a response 502.5 for 100 ppm butyl acetate with 100 ppb detection limit, and the response for 100 ppm butyl acetate is at least 6.2 times higher than 100 ppm methanol, 100 ppm benzene, 100 ppm triethylamine, 100 ppm isopropanol, 100 ppm ethyl acetate and 100 ppm formic acid. X-ray photoelectron spectroscopy (XPS) explores the change of oxygen vacancies in sensor accompanied with the addition of Ni element and reveales the reason for the change of oxygen vacancies.
RESUMO
To solve the structural strength problem of a MEMS arming device for a fuze, a kind of arming device applied to a certain type of 40 mm grenade is designed. This paper introduces the working principle of the arming device; simulates the shear pin, rotary pin and locking mechanism in the device; designs a variety of different test tools for test verification; and further increases the explosion reliability and arming safety tests. The results show that the arming device improves the structural strength and can meet the action requirements of a certain type of 40 mm grenade for safety release, as well as the application requirements of explosion reliability and arming safety.
RESUMO
This paper introduces the working principle of a MEMS safety and arming (S&A) device for a fuze that is installed perpendicular to the axis of the projectile. Additionally, the application of low-speed wire electrical discharge machining (EDM) in the fabrication of the device is proposed. Microsprings are susceptible to flexural deformation and secondary deformation in the EDM process, a problem that is solved by designing the auxiliary support beam, using multiple cuts, destress annealing and optimizing the processing parameters. The difficult problem of setback slider deformation in the principle prototype test is properly solved by establishing V-shaped grooves at both ends of the setback slider. The connection mode between the microspring and the frame is changed to a clearance fit connection. The improved setback arming device can guarantee service process safety and launch reliability. The maximum overload that can be withstood in service processing is 20,000 g, and the minimum overload for safety release during launch is 12,000 g. The results show that the EDM process can greatly reduce the machining cost while improving the machining precision and machining speed, which can compensate for the defects of the current manufacturing technology.
RESUMO
One-dimensional Zn-doped α-Fe2O3 nanowires have been controllably synthesized by using the pure pyrite as the source of Fe element through a two-step synthesis route, including the preparation of Fe source solution by a leaching process and the thermal conversion of the precursor solution into α-Fe2O3 nanowires by the hydrothermal and calcination process. The microstructure, morphology, and surface composition of the obtained products were characterized by X-ray diffraction, scanning electron microscopy, transmission electron microscopy, and X-ray photoelectron spectroscopy. It was found that the formation process of α-Fe2O3 is significantly influenced by the introduction of Zn2+. The gas sensing measurements indicated that the sensor based on 1% Zn-doped α-Fe2O3 nanowires showed excellent H2S sensing properties at the optimum operating temperature of 175 °C. Notably, the sensor showed a low H2S detection limit of 50 ppb with a sensor response of 1.5. Such high-performance sensing would be ascribed to the one-dimensional structure and high specific surface area of the prepared 1% Zn-doped α-Fe2O3 nanowires, which can not only provide a large number of surface active sites for the adsorption and reaction of the oxygen and H2S molecules, but also facilitate the diffusion of the gas molecules towards the entire sensing materials.
RESUMO
Nanostructured tungsten trioxide porous films were prepared by a non-hydrolytic solâ»gel method following the inorganic route in which ethanol and PEG were used as the oxygen-donor and structure-directing reagent, respectively. The effects of aging time of the precursor solution, PEG content, and calcination temperature on the structure, morphology, and NO2 sensing properties of WO3 films were systematically investigated by using the techniques of X-ray diffraction, field emission scanning electron microscopy, transmission electron microscopy, and gas sensing measurements. The results demonstrated that a series of WO3 films with different microstructures could be obtained by manipulating the synthesis parameters. Furthermore, a suitable synthesis condition of WO3 films for NO2 sensing application was determined.