Sustainable management of campus fallen leaves through low-temperature pyrolysis and application in Pb immobilization.

Realizing campus sustainability requires the environmental-friendly and economical treatment of tremendous fallen leaves. Producing fallen leaf biochar at a low temperature is a candidate approach. In this study, six common types of fallen leaves on the campus were pyrolyzed at 300 °C. The obtained biochars were characterized and the adsorption mechanisms of lead (Pb) by the fallen leaf biochars were investigated. The adsorption capacity of leaf biochar for Pb was relatively high, up to 209 mg/g (Yulania denudata leaf biochar). Adsorption of Pb onto active sites was the rate-limiting step for most leaf biochars. But for Platanus leaf biochar, intraparticle diffusion of Pb2+ dominated owing to the lowest adsorption capacity. However, the highest exchangeable Pb fraction (27%) indicated its potential for removing aqueous Pb2+. Ginkgo and Prunus cerasifera leaf biochar immobilized Pb by surface complexation and precipitation as lead oxalate. Hence, they were suitable for soil heavy metal remediation. This study shed the light on the sustainable utilization of campus fallen leaves and the application of fallen leaf biochars in heavy metal remediation.

Biochar Aging: Mechanisms, Physicochemical Changes, Assessment, And Implications for Field Applications.

Biochar has triggered a black gold rush in environmental studies as a carbon-rich material with well-developed porous structure and tunable functionality. While much attention has been placed on its apparent ability to store carbon in the ground, immobilize soil pollutants, and improve soil fertility, its temporally evolving in situ performance in these roles must not be overlooked. After field application, various environmental factors, such as temperature variations, precipitation events and microbial activities, can lead to its fragmentation, dissolution, and oxidation, thus causing drastic changes to the physicochemical properties. Direct monitoring of biochar-amended soils can provide good evidence of its temporal evolution, but this requires long-term field trials. Various artificial aging methods, such as chemical oxidation, wet-dry cycling and mineral modification, have therefore been designed to mimic natural aging mechanisms. Here we evaluate the science of biochar aging, critically summarize aging-induced changes to biochar properties, and offer a state-of-the-art for artificial aging simulation approaches. In addition, the implications of biochar aging are also considered regarding its potential development and deployment as a soil amendment. We suggest that for improved simulation and prediction, artificial aging methods must shift from qualitative to quantitative approaches. Furthermore, artificial preaging may serve to synthesize engineered biochars for green and sustainable environmental applications.

Effects of excessive impregnation, magnesium content, and pyrolysis temperature on MgO-coated watermelon rind biochar and its lead removal capacity.

MgO-coated watermelon rind biochar (MWRB) is a potentially highly-effective waste-derived material in environmental applications. This research aims to provide valuable insights into the optimization of the production of MWRB for superior environmental performance. It was found that the Mg content of the MWRB could be easily controlled by adjusting the Mg/feedstock mass ratio during excessive impregnation. The BET surface area was found to first increase and then decrease as the Mg content of the MWRB (produced at 600 °C) increased from 1.52% to 10.1%, with an optimal surface area of 293 m2/g observed at 2.51%. Similarly, an optimum pyrolysis temperature of 600 °C was observed in the range of 400-800 °C for a maximum surface area of the MWRB at a fixed Mg/feedstock ratio of 0.48% (resulting in MWRBs with Mg contents of 1.89-2.51%). The Pb removal capacity of the MWRB (produced at 600 °C) increased with increasing Mg content, with a greatest Pb removal capacity of 558 mg/g found for the MWRB with the highest Mg content (10.1%), an improvement of 208% over the 181 mg/g Pb removal capacity of unmodified WRB produced at 600 °C. The Pb removal capacity of the MWRB (produced with 1.89-2.51% Mg) was also discovered to increase from 81.7 mg/g (at 400 °C) to 742 mg/g (at 700 °C), before dropping to 368 mg/g at 800 °C. These findings suggest that the MWRB can be more efficiently utilized in soil and water remediation by optimizing its synthesis conditions.

The impacts of exogenous phosphorus on Cd absorption in perennial ryegrass root cell: Kinetic and mechanism study.

Phosphorus (P) is critical to plants in metal-contaminated soils because it participates in various biochemical reactions during plant growth. However, the mechanisms of P in mitigating the toxicity of heavy metals to ryegrass root is still veiled. In this study, the physiological and biochemical dynamics of the ryegrass root under various cadmium (Cd) and P conditions were investigated in a hydroponic system. Cd stress decreased the length of the ryegrass root, but P application enhanced the root elongation to reduce the Cd concentration in the root. Both Cd and P dosages were positively correlated with hemicellulose 1 content, pectin content, and PME activity, while having a negative effect on cellulose content. Moreover, the addition of 80 mg L-1 P increased the contents of pectin and hemicellulose 1 by 2.5 and 5.8% even with 4 mg L-1 Cd. In addition, P supply increased pectin methylesterbase activity under Cd stress, which further changed the extra-cytoplasmic structures and cell wall composition. Thus, exogenous P promoted the immobilization of Cd onto the cell wall and protected protoplast primarily through indirectly regulating the binding capacity of the root cell wall for Cd.

The role of soil structure on the cracking and cadmium leaching behavior of biochar-amended fine-grained soils.

Biochar has shown promising potential for soil remediation, yet its impact on heavy metals (HMs) immobilization often overlooks soil structure, which could influence soil cracking behavior and HMs transport. To address this gap, this study investigates the role of soil structure (dry density and aggregate size) on the cracking and cadmium (Cd) leaching behavior of biochar-amended fine-grained soils. A series of semi-dynamic leaching tests were conducted on samples with and without wetting-drying (W-D) cycles. Based on the proposed improved method for quantifying the effective diffusion coefficient (De) of Cd in unsaturated soils and microstructural analyses, we found that: (1) Higher dry density and larger aggregate generally resulted in smaller De by decreasing soil pore volume. (2) Biochar could connect isolated pores within large aggregates through its internal pores, yielding greater increases in De (294.8%-469.0%) compared to small aggregates (29.1%-77.4%) with 3% biochar. However, further increases in biochar dosage led to decreased De, primarily due to the dense pore structure. (3) Biochar effectively inhibited soil cracking, achieving the highest reduction of 36.8% in surface crack ratio. (4) After W-D cycles, samples exhibited higher De with increasing dry density, with aggravated cracking being the primary cause, suggesting preferential flow within the cracks, particularly those penetrating the soil. This study highlights the importance of careful consideration of soil structure and cracking potential before in situ field application of biochar as a remediation agent for HMs-contaminated fine-grained soils.

On-site monitoring and numerical simulation on groundwater flow and pollution plume evolution in a hexavalent-chromium contaminated site.

Accurately ascertaining spatiotemporal distribution of pollution plume is critical for evaluating the effectiveness of remediation technologies and environmental risks associated with contaminated sites. This study concentrated on a typical Cr(VI) contaminated smelter being currently remediated using pump-and-treat (PAT) technology. Long-term on-site monitoring data revealed that two highly polluted regions with Cr(VI) concentrations of 162.9 mg/L and 234.5 mg/L existed within the contaminated site, corresponding to previous chromium slag yard and sewage treatment plant, respectively. The PAT technology showed significant removal performance in these highly polluted areas (>160 mg/L) after six months of pumping, ultimately achieving complete removal of the pollutants in these high-pollution areas. Numerical simulation results showed that although the current remediation scheme significantly reduced the Cr(VI) pollution degree, it did not effectively prevent the incursion of the pollution plume into the downstream residential area after 20 years. Additionally, an improved measure involving supplementary pumping wells was proposed, and its remediation effects were quantitatively evaluated. Results indicated that the environmental pollution risk of groundwater downstream could be effectively mitigated by adding pumping wells, resulting in a reduction of the pollution area by 20 % in the case of adding an internal well and 41 % with the addition of external wells after 20 years. The findings obtained in this study will provide an important reference and theoretical guidance for the reliability analysis and design improvement of the PAT remediation project.

Synthesis and application of waste-based layered double hydroxide: A review.

The synthesis of layered double hydroxide (LDH) from industrial wastes is a sustainable approach to aid circular economy and hazardous material disposal. In this review, the researches on the synthesis and application of waste-based LDH from 2010 to 2023 are summarized and discussed. At present, there are mainly four types of waste-based LDH produced from red mud, slag, fly ash and wastewater, with co-precipitation being the most typical synthesis method. Red mud is used as the trivalent metal source supplemented by chemical reagents or other types of waste as divalent metal source to produce red mud-based LDH. Slag can act as the sole metal source providing both divalent and trivalent metal sources for slag-based LDH. Fly ash was used either as the trivalent metal source or both divalent and trivalent metal sources to produce fly ash-based LDH. Wastewater-based LDH was typically synthesized by in-situ co-precipitation method to achieve the self-purification of wastewater. The impurities in waste-based LDH can act as a two-edged weapon. It may either hinder or promote the performance of waste-based LDH. The challenge in the synthesis of waste-based LDH lies in the efficient extraction of available metals. The future research prospects for waste-based LDH are suggested.

Biochar implications for the engineering properties of soils: A review.

Use of biochar as a soil amendment for climate change mitigation and environmental remediation has been intensively studied over the past decade, yet the growing interest in biochar for geo-environmental applications is primarily motivated by its active interactions with soil in terms of engineering properties. The addition of biochar can significantly alter the physical, hydrological, and mechanical properties of soils, but the diverse biochar characteristics and soil properties lead to the fact that a generalized conclusion on the impact of biochar on soil engineering properties is difficult to reach. Considering that the effects of biochar on soil engineering properties could also potentially affect the applications of biochar in other fields, this review intends to provide a comprehensive and critical overview of biochar implications for soil engineering properties. Based on the physicochemical properties of biochar pyrolyzed from varying feedstocks and pyrolysis temperatures, this review analyzed the physical, hydrological, and mechanical performances of biochar-amended soils and the underlying mechanisms. Among others, the analysis releases that the initial state of biochar-amended soil requires special attention when evaluating the effect of biochar on soil engineering properties, yet it is usually neglected in the current studies. The review closes with a brief overview of the potential impacts of engineering properties on other soil processes, and future needs and opportunities for further development of biochar in geo-environmental engineering from academia to practice.

Enhancing lead immobilization by biochar: Creation of "surface barrier" via bio-treatment.

The long-term effectiveness of heavy metal immobilization is always a concern. This study proposes a completely novel approach to enhance the stability of heavy metals by combined biochar and microbial induced carbonate precipitation (MICP) technology, to create a "surface barrier" of CaCO3 layer on biochar after lead (Pb2+) immobilization. Aqueous sorption studies and chemical and micro-structure tests were used to verify the feasibility. Rice straw biochar (RSB700) was produced at 700 °C, which shows high immobilization capacity of Pb2+ (maximum of 118 mg g-1). But the stable fraction only accounts for 4.8% of the total immobilized Pb2+ on biochar. After MICP treatment, the stable fraction of Pb2+ significantly increased to a maximum of 92.5%. Microstructural tests confirm the formation of CaCO3 layer on biochar. The CaCO3 species are predominantly calcite and vaterite. Higher Ca2+ and urea concentrations in cementation solution resulted in higher CaCO3 yield but lower Ca2+ utilization efficiency. The main mechanism of the "surface barrier" to enhance Pb2+ stability on biochar was likely the encapsulation effect: it physically blocked the contact between acids and Pb2+ on biochar, and chemically buffer the acidic attack from the environment. The performance of the "surface barrier" depends on both the yield of CaCO3 and their distribution uniformity on biochar's surface. This study shed lights on the potential application of the "surface barrier" strategy combining biochar and MICP technologies for enhanced heavy metal immobilization.