Coupled defects in one-dimensional photonic crystal films fabricated with glancing angle deposition.

This work presents the successful fabrication of 1D photonic crystals (PCs) with two defects using the glancing angle deposition (GLAD) technique. We study the coupling behavior of the two PC defects and demonstrate the ability to control the defect interaction. GLAD allows engineering of film nanostructure to produce PCs with sinusoidal refractive index variation through control of film nanostructure and porosity. Two phase-shift defects are introduced into the refractive index profile of the film. The observed defect-defect coupling is explained by a coupled-oscillator model and the interaction strength is found to decrease exponentially with increasing defect separation. Furthermore, the results demonstrate the promise of GLAD as a platform technology for PC research and device fabrication.

Surface area characterization of obliquely deposited metal oxide nanostructured thin films.

The glancing angle deposition (GLAD) technique is used to fabricate nanostructured thin films with high surface area. Quantifying this property is important for optimizing GLAD-based device performance. Our group has used high-sensitivity krypton gas adsorption and the complementary technique of cyclic voltammetry to measure surface area as a function of deposition angle, thickness, and morphological characteristics for several metal oxide thin films. In this work, we studied amorphous titanium dioxide (TiO(2)), amorphous silicon dioxide (SiO(2)), and polycrystalline indium tin oxide (ITO) nanostructures with vertical and helical post morphologies over a range of oblique deposition angles from 0 to 86 degrees. Krypton gas sorption isotherms, evaluated using the Brunauer-Emmettt-Teller (BET) method, revealed maximum surface area enhancements of 880 +/- 110, 980 +/- 125, and 210 +/- 30 times the footprint area (equivalently 300 +/- 40, 570 +/- 70, and 50 +/- 6 m(2) g(-1)) for vertical posts TiO(2), SiO(2), and ITO. We also applied the cyclic voltammetry technique to these ITO films and observed the same overall trends as seen with the BET method. In addition, we applied the BET method to the measurement of helical films and found that the surface area trend was shifted with respect to that of vertical post films. This revealed the important influence of the substrate rotation rate and film morphology on surface properties. Finally, we showed that the surface area scales linearly with film thickness, with slopes of 730 +/- 35 to 235 +/- 10 m(2) m(-2) microm(-1) found for titania vertical post films deposited at angles from 70 to 85 degrees. This characterization effort will allow for the optimization of solar, photonic, and sensing devices fabricated from thin metal oxide films using GLAD.

The use of ion-milling to control clustering of nanostructured, columnar thin films.

We present the use of ion-milling to reduce the capillary-induced clustering of vertical post nanostructures grown by glancing angle deposition. Nanostructures of several heights were grown and ion-milled for various times to investigate effects on post clustering. No clustering was observed given sufficient ion-mill exposure time, with the characteristic time being lower for shorter posts. The results demonstrate that these strengthened nanostructures are suitable for use in liquid environments.

Circular birefringence dependence on chiral film porosity.

Obliquely deposited thin films with helical microstructures exhibit circular Bragg effects. In this study, the effect of film porosity on the circular birefringence of helical thin films is investigated in TiO(2) films deposited at angles ranging from 30 degrees to 87 degrees in order to determine the various mechanisms responsible for the circular Bragg effects. Specular transmittance and diffuse scattering measurements indicate two film growth regimes of enhanced circular Bragg effects: The first regime is due to a maximum in form birefringence while the second regime is caused by strong anisotropic scattering.

Photoluminescence emission profiles of Y(2)O(3) : Eu films composed of high-low density stacks produced by glancing angle deposition.

Periodic high-/low-index film stacks composed of Y(2)O(3) : Eu were grown by glancing angle deposition on silicon and fused silica substrates. Postdeposition annealing at temperatures from 600 to 1000 degrees C for 1 h in air was performed to activate photoluminescence. Absolute photoluminescence spectra were obtained as a function of observation angle. The angular emission distribution was non-Lambertian, with peak emission at angles of 50 to 60 degrees with respect to substrate normal. Spectroscopic transmittance and ellipsometry measurements were performed to characterize the films. Using this description, we were able to reproduce the angular photoluminescence patterns of the films.

Formation and aqueous surface wettability of polysiloxane nanofibers prepared via surface initiated, vapor-phase polymerization of organotrichlorosilanes.

The formation of high aspect ratio organosiloxane fibers of nanodimensionality via the surface-induced vapor-phase polymerization of vinyltrichlorosilane is reported. We also demonstrate the versatility of our method by producing fibers of various densities, polydispersities, and lengths. Nanofibers were characterized using SEM, EDX, XPS, TOF-SIMS, and variable-angle FTIR. Advancing aqueous contact angle measurements were used to evaluate the nanofiber surface wettability.

Sidelobe suppression in chiral optical filters by apodization of the local form birefringence.

Chiral optical filters are characterized by circular Bragg effects, including the preferential reflection and transmission of circular polarization states. The selective response to circularly polarized light is caused by stratified birefringent plates twisted into a helical arrangement, as seen in cholesteric liquid crystals and columnar thin films produced by oblique-angle physical vapor deposition. A refinement of the latter, glancing angle deposition employs substrate rotation to control the optical anisotropy of columnar thin films, and was used in this study to suppress the reflection sidelobes of chiral optical filters by modulating the local birefringence of helically structured thin films using an apodization function. Both theoretical simulations based on Berreman formalism, and experimental results involving evaporated TiO(2) thin films are presented and compared.

Gradient-index narrow-bandpass filter fabricated with glancing-angle deposition.

Glancing-angle deposition (GLAD) is a fabrication method capable of producing thin films with engineered nanoscale porosity variations. GLAD can be used to create optical thin-film interference filters from a single source material by modification of the film refractive index through control of film porosity. We present the effects of introducing a layer of constant low density into the center of a rugate thin-film filter fabricated with the GLAD technique. A rugate filter is characterized by a sinusoidal refractive-index profile. Embedding a layer of constant refractive index, with a thickness equal to one period of the rugate index variation, causes a narrow bandpass to appear within the filter's larger stop band. Transmittance measurements of such a gradient-index narrow-bandpass filter, formed with titanium dioxide, revealed an 83% transmittance peak at a vacuum wavelength of 522 nm, near the center of the stop band, with a FWHM bandwidth of 15 nm.

Optical properties of porous helical thin films.

Porous dielectric thin films, composed of isolated helical columns, are fabricated by the glancing angle deposition technique. The selective reflection of circularly polarized light and the optical rotation of linearly polarized light are investigated as a function of film material and helical morphology. The strongest chiral optical response is observed for titanium-dioxide films because of its large refractive index. Optical rotatory powers as high as 4.5 degrees are observed in 830-nm-thick helical films. By tailoring the pitch of the helical columns, the wavelength dependence of the circular reflection band is tuned to preferentially reflect red, green, or blue light, a promising quality for display applications.