A 3D Printable Electroconductive Biocomposite Bioink Based on Silk Fibroin-Conjugated Graphene Oxide.

Reduced graphene oxide (rGO) has wide application as a nanofiller in the fabrication of electroconductive biocomposites due to its exceptional properties. However, the hydrophobicity and chemical stability of rGO limit its ability to be incorporated into precursor polymers for physical mixing during biocomposite fabrication. Moreover, until now, no suitable rGO-combining biomaterials that are stable, soluble, biocompatible, and 3D printable have been developed. In this study, we fabricated digital light processing (DLP) printable bioink (SGOB1), through covalent reduction of graphene oxide (GO) by glycidyl methacrylated silk fibroin (SB). Compositional analyses showed that SGOB1 contains approximately 8.42% GO in its reduced state. Our results also showed that the rGO content of SGOB1 became more thermally stable and highly soluble. SGOB1 hydrogels demonstrated superior mechanical, electroconductive, and neurogenic properties than (SB). Furthermore, the photocurable bioink supported Neuro2a cell proliferation and viability. Therefore, SGOB1 could be a suitable biocomposite for neural tissue engineering.

Silk Fibroin in Wound Healing Process.

Silk fibroin (SF), a natural bioproduct, has been extensively used in biological and biomedical fields including wound healing due to its robust biocompatibility, less immunogenic, non-toxic, non-carcinogenic, and biodegradable properties. SF in different morphologic forms, such as hydrogels, sponges, films, electrospun nanofiber mats, and hydrocolloid dressings, have been successfully used for therapeutic use as wound dressings to induce the healing process. SF has also been known to promote wound healing by increasing the cell growth, proliferation, and migration of different cells types involved in the different phase of wound healing process. In this review, we summarize the different morphologic forms of SF that have been used in the treatment of various wound healing process. We also discuss the effect of SF on various cells types during the SF-induced healing process. Furthermore, we highlight molecular signaling aspects of the SF-induced healing process.

Artificial Auricular Cartilage Using Silk Fibroin and Polyvinyl Alcohol Hydrogel.

Several methods for auricular cartilage engineering use tissue engineering techniques. However, an ideal method for engineering auricular cartilage has not been reported. To address this issue, we developed a strategy to engineer auricular cartilage using silk fibroin (SF) and polyvinyl alcohol (PVA) hydrogel. We constructed different hydrogels with various ratios of SF and PVA by using salt leaching, silicone mold casting, and freeze-thawing methods. We characterized each of the hydrogels in terms of the swelling ratio, tensile strength, pore size, thermal properties, morphologies, and chemical properties. Based on the cell viability results, we found a blended hydrogel composed of 50% PVA and 50% SF (P50/S50) to be the best hydrogel among the fabricated hydrogels. An intact 3D ear-shaped auricular cartilage formed six weeks after the subcutaneous implantation of a chondrocyte-seeded 3D ear-shaped P50/S50 hydrogel in rats. We observed mature cartilage with a typical lacunar structure both in vitro and in vivo via histological analysis. This study may have potential applications in auricular tissue engineering with a human ear-shaped hydrogel.

Identification of Lys49-PLA2 from crude venom of Crotalus atrox as a human neutrophil-calcium modulating protein.

We fortuitously observed a human neutrophil intracellular free-calcium concentration ([Ca(2+)]i) increasing activity in the commercially available phosphodiesterase I (PDE I), which is actually dried crude venom of Crotalus atrox. As this activity was not observed with another commercially available pure PDE I, we tried to find out the causative molecule(s) present in 'crude' PDE, and identified Lys49-phospholipase A2 (Lys49-PLA2 or K49-PLA2), a catalytically inactive protein which belongs to the phospholipase A2 family, by activity-driven three HPLC (reverse phase, size exclusion, reverse phase) steps followed by SDS-PAGE and LC-MS/MS. K49-PLA2 induced Ca(2+) infl ux in human neutrophils without any cytotoxic eff ect. Two calcium channel inhibitors, 2-aminoetoxydiphenyl borate (2-APB) (30 µM) and SKF-96365 (20 µM) signifi cantly inhibited K49-PLA2-induced [Ca(2+)]i increase. These results suggest that K49-PLA2 modulates [Ca(2+)]i in human neutrophils via 2-APB- and SKF-96365-sensitive calcium channels without causing membrane disruption.

Scant Extracellular NAD Cleaving Activity of Human Neutrophils is Down-Regulated by fMLP via FPRL1.

Extracellular nicotinamide adenine dinucleotide (NAD) cleaving activity of a particular cell type determines the rate of the degradation of extracellular NAD with formation of metabolites in the vicinity of the plasma membrane, which has important physiological consequences. It is yet to be elucidated whether intact human neutrophils have any extracellular NAD cleaving activity. In this study, with a simple fluorometric assay utilizing 1,N(6)-ethenoadenine dinucleotide (etheno-NAD) as the substrate, we have shown that intact peripheral human neutrophils have scant extracellular etheno-NAD cleaving activity, which is much less than that of mouse bone marrow neutrophils, mouse peripheral neutrophils, human monocytes and lymphocytes. With high performance liquid chromatography (HPLC), we have identified that ADP-ribose (ADPR) is the major extracellular metabolite of NAD degradation by intact human neutrophils. The scant extracellular etheno-NAD cleaving activity is decreased further by N-formyl-methionine-leucine-phenylalanine (fMLP), a chemoattractant for neutrophils. The fMLP-mediated decrease in the extracellular etheno-NAD cleaving activity is reversed by WRW4, a potent FPRL1 antagonist. These findings show that a much less extracellular etheno-NAD cleaving activity of intact human neutrophils compared to other immune cell types is down-regulated by fMLP via a low affinity fMLP receptor FPRL1.

SPAK inhibitor ZT-1a attenuates reactive astrogliosis and oligodendrocyte degeneration in a mouse model of vascular dementia.

BACKGROUND: Astrogliosis and white matter lesions (WML) are key characteristics of vascular contributions to cognitive impairment and dementia (VCID). However, the molecular mechanisms underlying VCID remain poorly understood. Stimulation of Na-K-Cl cotransport 1 (NKCC1) and its upstream kinases WNK (with no lysine) and SPAK (the STE20/SPS1-related proline/alanine-rich kinase) play a role in astrocytic intracellular Na+ overload, hypertrophy, and swelling. Therefore, in this study, we assessed the effect of SPAK inhibitor ZT-1a on pathogenesis and cognitive function in a mouse model of VCID induced by bilateral carotid artery stenosis (BCAS). METHODS: Following sham or BCAS surgery, mice were randomly assigned to receive either vehicle (DMSO) or SPAK inhibitor ZT-1a treatment regimen (days 14-35 post-surgery). Mice were then evaluated for cognitive functions by Morris water maze, WML by ex vivo MRI-DTI analysis, and astrogliosis/demyelination by immunofluorescence and immunoblotting. RESULTS: Compared to sham control mice, BCAS-Veh mice exhibited chronic cerebral hypoperfusion and memory impairments, accompanied by significant MRI DTI-detected WML and oligodendrocyte (OL) death. Increased activation of WNK-SPAK-NKCC1-signaling proteins was detected in white matter tissues and in C3d+ GFAP+ cytotoxic astrocytes but not in S100A10+ GFAP+ homeostatic astrocytes in BCAS-Veh mice. In contrast, ZT-1a-treated BCAS mice displayed reduced expression and phosphorylation of NKCC1, decreased astrogliosis, OL death, and WML, along with improved memory functions. CONCLUSION: BCAS-induced upregulation of WNK-SPAK-NKCC1 signaling contributes to white matter-reactive astrogliosis, OL death, and memory impairment. Pharmacological inhibition of the SPAK activity has therapeutic potential for alleviating pathogenesis and memory impairment in VCID.

Functional Skeletal Muscle Regeneration Using Muscle Mimetic Tissue Fabricated by Microvalve-Assisted Coaxial 3D Bioprinting.

3D-printed artificial skeletal muscle, which mimics the structural and functional characteristics of native skeletal muscle, is a promising treatment method for muscle reconstruction. Although various fabrication techniques for skeletal muscle using 3D bio-printers are studied, it is still challenging to build a functional muscle structure. A strategy using microvalve-assisted coaxial 3D bioprinting in consideration of functional skeletal muscle fabrication is reported. The unit (artificial muscle fascicle: AMF) of muscle mimetic tissue is composed of a core filled with medium-based C2C12 myoblast aggregates as a role of muscle fibers and a photo cross-linkable hydrogel-based shell as a role of connective tissue in muscles that enhances printability and cell adhesion and proliferation. Especially, a microvalve system is applied for the core part with even cell distribution and strong cell-cell interaction. This system enhances myotube formation and consequently shows spontaneous contraction. A multi-printed AMF (artificial muscle tissue: AMT) as a piece of muscle is implanted into the anterior tibia (TA) muscle defect site of immunocompromised rats. As a result, the TA-implanted AMT responds to electrical stimulation and represents histologically regenerated muscle tissue. This microvalve-assisted coaxial 3D bioprinting shows a significant step forward to mimicking native skeletal muscle tissue.

Fluidic integrated 3D bioprinting system to sustain cell viability towards larynx fabrication.

Herein, we report the first study to create a three-dimensional (3D) bioprinted artificial larynx for whole-laryngeal replacement. Our 3D bio-printed larynx was generated using extrusion-based 3D bioprinter with rabbit's chondrocyte-laden gelatin methacryloyl (GelMA)/glycidyl-methacrylated hyaluronic acid (GMHA) hybrid bioink. We used a polycaprolactone (PCL) outer framework incorporated with pores to achieve the structural strength of printed constructs, as well as to provide a suitable microenvironment to support printed cells. Notably, we established a novel fluidics supply (FS) system that simultaneously supplies basal medium together with a 3D bioprinting process, thereby improving cell survival during the printing process. Our results showed that the FS system enhanced post-printing cell viability, which enabled the generation of a large-scale cell-laden artificial laryngeal framework. Additionally, the incorporation of the PCL outer framework with pores and inner hydrogel provides structural stability and sufficient nutrient/oxygen transport. An animal study confirmed that the transplanted 3D bio-larynx successfully maintained the airway. With further development, our new strategy holds great potential for fabricating human-scale larynxes with in vivo-like biological functions for laryngectomy patients.

A digital light processing 3D-printed artificial skin model and full-thickness wound models using silk fibroin bioink.

A three-dimensional (3D) artificial skin model offers diverse platforms for skin transplantation, disease mechanisms, and biomaterial testing for skin tissue. However, implementing physiological complexes such as the neurovascular system with living cells in this stratified structure is extremely difficult. In this study, full-thickness skin models were fabricated from methacrylated silk fibroin (Silk-GMA) and gelatin (Gel-GMA) seeded with keratinocytes, fibroblasts, and vascular endothelial cells representing the epidermis and dermis layers through a digital light processing (DLP) 3D printer. Printability, mechanical properties, and cell viability of the skin hydrogels fabricated with different concentrations of Silk-GMA and Gel-GMA were analyzed to find the optimal concentrations for the 3D printing of the artificial skin model. After the skin model was DLP-3D printed using Gel-GMA 15% + Silk-GMA 5% bioink, cultured, and air-lifted for four weeks, well-proliferated keratinocytes and fibroblasts were observed in histological analysis, and increased expressions of Cytokeratin 13, Phalloidin, and CD31 were noted in immunofluorescence staining. Furthermore, full-thickness skin wound models were 3D-printed to evaluate the wound-healing capabilities of the skin hydrogel. When the epidermal growth factor (EGF) was applied, enhanced wound healing in the epidermis and dermis layer with the proliferation of keratinocytes and fibroblasts was observed. Also, the semi-quantitative reverse transcription-polymerase chain reaction revealed increased expression of Cytokeratin 13, fibroblast growth factor, and CD31 in the EGF-treated group relative to the control group. The DLP 3D-printed artificial skin model was mechanically stable and biocompatible for more than four weeks, demonstrating the potential for application in skin tissue engineering. STATEMENT OF SIGNIFICANCE: A full-thickness artificial skin model was 3D-printed in this study with a digital light processing technique using silk fibroin and gelatin, which mimics the structural and cellular compositions of the human skin. The 3D-printed skin hydrogel ensured the viability of the cells in the skin layers that proliferated well after air-lifting cultivation, shown in the histological analysis and immunofluorescence stainings. Furthermore, full-thickness skin wound models were 3D-printed to evaluate the wound healing capabilities of the skin hydrogel, which demonstrated enhanced wound healing in the epidermis and dermis layer with the application of epidermal growth factor on the wound compared to the control. The bioengineered hydrogel expands the applicability of artificial skin models for skin substitutes, wound models, and drug testing.

Three-Dimensional Digital Light-Processing Bioprinting Using Silk Fibroin-Based Bio-Ink: Recent Advancements in Biomedical Applications.

Three-dimensional (3D) bioprinting has been developed as a viable method for fabricating functional tissues and organs by precisely spatially arranging biomaterials, cells, and biochemical components in a layer-by-layer fashion. Among the various bioprinting strategies, digital light-processing (DLP) printing has gained enormous attention due to its applications in tissue engineering and biomedical fields. It allows for high spatial resolution and the rapid printing of complex structures. Although bio-ink is a critical aspect of 3D bioprinting, only a few bio-inks have been used for DLP bioprinting in contrast to the number of bio-inks employed for other bioprinters. Recently, silk fibroin (SF), as a natural bio-ink material used for DLP 3D bioprinting, has gained extensive attention with respect to biomedical applications due to its biocompatibility and mechanical properties. This review introduces DLP-based 3D bioprinting, its related technology, and the fabrication process of silk fibroin-based bio-ink. Then, we summarize the applications of DLP 3D bioprinting based on SF-based bio-ink in the tissue engineering and biomedical fields. We also discuss the current limitations and future perspectives of DLP 3D bioprinting using SF-based bio-ink.

Silk Fibroin-Based Biomaterials for Hemostatic Applications.

Hemostasis plays an essential role in all surgical procedures. Uncontrolled hemorrhage is the primary cause of death during surgeries, and effective blood loss control can significantly reduce mortality. For modern surgeons to select the right agent at the right time, they must understand the mechanisms of action, the effectiveness, and the possible adverse effects of each agent. Over the past decade, various hemostatic agents have grown intensely. These agents vary from absorbable topical hemostats, including collagen, gelatins, microfibrillar, and regenerated oxidized cellulose, to biologically active topical hemostats such as thrombin, biological adhesives, and other combined agents. Commercially available products have since expanded to include topical hemostats, surgical sealants, and adhesives. Silk is a natural protein consisting of fibroin and sericin. Silk fibroin (SF), derived from silkworm Bombyx mori, is a fibrous protein that has been used mostly in fashion textiles and surgical sutures. Additionally, SF has been widely applied as a potential biomaterial in several biomedical and biotechnological fields. Furthermore, SF has been employed as a hemostatic agent in several studies. In this review, we summarize the several morphologic forms of SF and the latest technological advances on the use of SF-based hemostatic agents.

3D bioprinted silk fibroin hydrogels for tissue engineering.

The development of biocompatible and precisely printable bioink addresses the growing demand for three-dimensional (3D) bioprinting applications in the field of tissue engineering. We developed a methacrylated photocurable silk fibroin (SF) bioink for digital light processing 3D bioprinting to generate structures with high mechanical stability and biocompatibility for tissue engineering applications. Procedure 1 describes the synthesis of photocurable methacrylated SF bioink, which takes 2 weeks to complete. Digital light processing is used to fabricate 3D hydrogels using the bioink (1.5 h), which are characterized in terms of methacrylation, printability, mechanical and rheological properties, and biocompatibility. The physicochemical properties of the bioink can be modulated by varying photopolymerization conditions such as the degree of methacrylation, light intensity, and concentration of the photoinitiator and bioink. The versatile bioink can be used broadly in a range of applications, including nerve tissue engineering through co-polymerization of the bioink with graphene oxide, and for wound healing as a sealant. Procedure 2 outlines how to apply 3D-printed SF hydrogels embedded with chondrocytes and turbinate-derived mesenchymal stem cells in one specific in vivo application, trachea tissue engineering, which takes 2-9 weeks.

Reinforced-hydrogel encapsulated hMSCs towards brain injury treatment by trans-septal approach.

Encapsulated stem cells in various biomaterials have become a potentially promising cell transplantation strategy in the treatment of various neurologic disorders. However, there is no ideal cell delivery material and method for clinical application in brain diseases. Here we show silk fibroin (SF)-based hydrogel encapsulated engineered human mesenchymal stem cells (hMSCs) to overproduce brain-derived neurotrophic factor (BDNF) (BDNF-hMSC) is an effective approach to treat brain injury through trans-septal cell transplantation in the rat model. In this study, we observed SF induced sustained BDNF production by BDNF-hMSC both in 2D (9.367 ± 1.969 ng/ml) and 3D (7.319 ± 0.1025 ng/ml) culture conditions for 3 days. Through immunohistochemistry using α-tubulin, BDNF-hMSCs showed a significant increased average neurite length of co-cultured neuro 2a (N2a) cells, suggested that BDNF-hMSCs induced neurogenesis in vitro. Encapsulated BDNF-hMSC, pre-labeled with the red fluorescent dye PKH-26, exhibited intense fluorescence up to 14 days trans-septal transplantation, indicated excellent viability of the transplanted cells. Compared to the vehicle-treated, encapsulated BDNF- hMSC demonstrated significantly increased BDNF level both in the sham-operated and injured hippocampus (Hip) through immunoblot analysis after 7 days implantation. Transplantation of the encapsulated BDNF-hMSC promoted neurological functional recovery via significantly reduced neuronal death in the Hip 7 days post-injury. Using magnetic resonance imaging (MRI) analysis, we demonstrated that encapsulated BDNF-hMSC reduced lesion area significantly at 14 and 21 days in the damaged brain following trans-septal implantation. This stem cell transplantation approach represents a critical set up towards brain injury treatment for clinical application.

Treatment of Fungal-Infected Diabetic Wounds with Low Temperature Plasma.

Diabetes mellitus renders patients susceptible to chronic wounds and various infections. Regarding the latter, fungal infections are of particular concern since, although they are the source of significant morbidity and mortality in immunocompromised patients, they are generally resistant to conventional treatment and a definite treatment strategy has not yet been established. Herein, we report the treatment of skin wounds in a diabetic rat model, infected by Candida albicans, with low temperature helium plasma generated in a hand-held atmospheric jet device. A fungal infection was induced on two dorsal skin wounds of the diabetic rats, and one wound was treated with the plasma jet whereas the other served as a control. Histological analysis revealed accelerated skin wound healing and decreased evidence of fungal infection in the plasma-treated group, as compared to the control group. Regeneration of the epidermis and dermis, collagen deposition, and neovascularization were all observed as a result of plasma treatment, but without wound contraction, scar formation or any evidence of thermal damage to the tissue. These findings demonstrate that the He plasma jet is remarkably effective in diabetic skin wounds infected by Candida albicans, thereby providing a promising medical treatment option for diabetes mellitus patients with skin wound and fungal infections.

A digital light processing 3D printed magnetic bioreactor system using silk magnetic bioink.

Among various bioreactors used in the field of tissue engineering and regenerative medicine, a magnetic bioreactor is more capable of providing steady force to the cells while avoiding direct manipulation of the materials. However, most of them are complex and difficult to fabricate, with drawbacks in terms of consistency and biocompatibility. In this study, a magnetic bioreactor system and a magnetic hydrogel were manufactured by single-stage three-dimensional (3D) printing with digital light processing (DLP) technique for differentiation of myoblast cells. The hydrogel was composed of a magnetic part containing iron oxide and glycidyl-methacrylated silk fibroin, and a cellular part printed by adding mouse myoblast cell (C2C12) to gelatin glycidyl methacrylate, that was placed in the magnetic bioreactor system to stimulate the cells in the hydrogel. The composite hydrogel was steadily printed by a one-stage layering technique using a DLP printer. The magnetic bioreactor offered mechanical stretching of the cells in the hydrogel in 3D ways, so that the cellular differentiation could be executed in three dimensions just like the human environment. Cell viability, as well as gene expression using quantitative reverse transcription-polymerase chain reaction, were assessed after magneto-mechanical stimulation of the myoblast cell-embedded hydrogel in the magnetic bioreactor system. Comparison with the control group revealed that the magnetic bioreactor system accelerated differentiation of mouse myoblast cells in the hydrogel and increased myotube diameter and lengthin vitro. The DLP-printed magnetic bioreactor and the hydrogel were simply manufactured and easy-to-use, providing an efficient environment for applying noninvasive mechanical force via FDA-approved silk fibroin and iron oxide biocomposite hydrogel, to stimulate cells without any evidence of cytotoxicity, demonstrating the potential for application in muscle tissue engineering.

Cytocompatibility of Modified Silk Fibroin with Glycidyl Methacrylate for Tissue Engineering and Biomedical Applications.

Hydrogel with chemical modification has been used for 3D printing in the biomedical field of cell and tissue-based regeneration because it provides a good cellular microenvironment and mechanical supportive ability. As a scaffold and a matrix, hydrogel itself has to be modified chemically and physically to form a ß-sheet crosslinking structure for the strength of the biomaterials. These chemical modifications could affect the biological damage done to encapsulated cells or surrounding tissues due to unreacted chemical residues. Biological assessment, including assessment of the cytocompatibility of hydrogel in clinical trials, must involve testing with cytotoxicity, irritation, and sensitization. Here, we modified silk fibroin and glycidyl methacrylate (Silk-GMA) and evaluated the physical characterizations, residual chemical detection, and the biological effect of residual GMA depending on dialysis periods. Silk-GMA depending on each dialysis period had a typical ß-sheet structure in the characterization analysis and residual GMA decreased from dialysis day 1. Moreover, cell proliferation and viability rate gradually increased; additionally, necrotic and apoptotic cells decreased from dialysis day 2. These results indicate that the dialysis periods during chemical modification of natural polymer are important for removing unreacted chemical residues and for the potential application of the manufacturing standardization for chemically modified hydrogel for the clinical transplantation for tissue engineering and biomedical applications.

Digital light processing 3D printed silk fibroin hydrogel for cartilage tissue engineering.

Three-dimensional printing with Digital Lighting Processing (DLP) printer has come into the new wave in the tissue engineering for regenerative medicine. Especially for the clinical application, it needs to develop of bio-ink with biocompatibility, biodegradability and printability. Therefore, we demonstrated that Silk fibroin as a natural polymer fabricated with glycidyl-methacrylate (Silk-GMA) for DLP 3D printing. The ability of chondrogenesis with chondrocyte-laden Silk-GMA evaluated in vitro culture system and applied in vivo. DLP 3D printing system provided 3D product with even cell distribution due to rapid printing speed and photopolymerization of DLP 3D printer. Up to 4 weeks in vitro cultivation of Silk-GMA hydrogel allows to ensure of viability, proliferation and differentiation to chondrogenesis of encapsulated cells. Moreover, in vivo experiments against partially defected trachea rabbit model demonstrated that new cartilage like tissue and epithelium found surrounding transplanted Silk-GMA hydrogel. This study promises the fabricated Silk GMA hydrogel using DLP 3D printer could be applied to the fields of tissue engineering needing mechanical properties like cartilage regeneration.

4D-bioprinted silk hydrogels for tissue engineering.

Recently, four-dimensional (4D) printing is emerging as the next-generation biofabrication technology. However, current 4D bioprinting lacks biocompatibility or multi-component printability. In addition, suitable implantable targets capable of applying 4D bioprinted products have not yet been established, except theoretical and in vitro study. Herein, we describe a cell-friendly and biocompatible 4D bioprinting system including more than two cell types based on digital light processing (DLP) and photocurable silk fibroin (Sil-MA) hydrogel. The shape changes of 3D printed bilayered Sil-MA hydrogels were controlled by modulating their interior or exterior properties in physiological conditions. We used finite element analysis (FEA) simulations to explore the possible changes in the complex structure. Finally, we made trachea mimetic tissue with two cell types using this 4D bioprinting system and implanted it into a damaged trachea of rabbit for 8 weeks. The implants were integrated with the host trachea naturally, and both epithelium and cartilage were formed at the predicted sites. These findings demonstrate that 4D bioprinting system could make tissue mimetic scaffold biologically and suggest the potential value of the 4D bioprinting system for tissue engineering and the clinical application.

Recirculating peritoneal dialysis system using urease-fixed silk fibroin membrane filter with spherical carbonaceous adsorbent.

The chronic kidney disease (CKD) patients are undergoing continuous ambulatory peritoneal dialysis (CAPD). However, there are some constraints, the frequent exchange of the dialysate and limitation of outside activity, associated with CAPD remain to be solved. In this study, we designed the wearable artificial kidney (WAK) system for peritoneal dialysis (PD) using urease-immobilized silk fibroin (SF) membrane and polymer-based spherical carbonaceous adsorbent (PSCA). We evaluated this kit's removal abilities of uremic toxins such as urea, creatinine, uric acid, phosphorus, and ß2-microglobulin from the dialysate of end-stage renal disease (ESRD) patients in vitro. The uremic toxins including urea, creatinine, uric acid, and phosphorus were removed about 99% by immobilized SF membrane and PSCA filter after 24 h treatment. However, only 50% of ß2-microglobulin was removed by this filtering system after 24 h treatment. In vivo study result shows that our filtering system has more uremic toxins removal efficiency than exchanged dialysate at every 6 h. We suggest that recirculating PD system using urease-immobilized SF membrane with PSCA could be more efficient than traditional dialysate exchange system for a WAK for PD.

New concept of 3D printed bone clip (polylactic acid/hydroxyapatite/silk composite) for internal fixation of bone fractures.

Open reduction with internal fixation is commonly used for the treatment of bone fractures. However, postoperative infection associated with internal fixation devices (intramedullary nails, plates, and screws) remains a significant complication, and it is technically difficult to fix multiple fragmented bony fractures using internal fixation devices. In addition, drilling in the bone to install devices can lead to secondary fracture, bone necrosis associated with postoperative infection. In this study, we developed bone clip type internal fixation device using three- dimensional (3D) printing technology. Standard 3D model of the bone clip was generated based on computed tomography (CT) scan of the femur in the rat. Polylacticacid (PLA), hydroxyapatite (HA), and silk were used for bone clip material. The purpose of this study was to characterize 3D printed PLA, PLA/HA, and PLA/HA/Silk composite bone clip and evaluate the feasibility of these bone clips as an internal fixation device. Based on the results, PLA/HA/Silk composite bone clip showed similar mechanical property, and superior biocompatibility compared to other types of the bone clip. PLA/HA/Silk composite bone clip demonstrated excellent alignment of the bony segments across the femur fracture site with well-positioned bone clip in an animal study. Our 3D printed bone clips have several advantages: (1) relatively noninvasive (drilling in the bone is not necessary), (2) patient-specific design (3) mechanically stable device, and (4) it provides high biocompatibility. Therefore, we suggest that our 3D printed PLA/HA/Silk composite bone clip is a possible internal fixation device.