Efficient Inverted Perovskite Photovoltaics Through Surface State Manipulation.

Inverted perovskite solar cells (PSCs) are considered as the most promising avenue for the commercialization of PSCs due to their potential inherent stability. However, suboptimal interface contacts between electron transport layer (ETL) (such as C60) and the perovskite absorbing layer within inverted PSCs always result in reduced efficiency and poor stability. Herein, a surface state manipulation strategy has been developed by employing a highly electronegative 4-fluorophenethylamine hydrochloride (p-F-PEACl) to effectively address the issue of poor interface contacts in the inverted PSCs. The p-F-PEACl demonstrates a robust interaction with perovskite film through bonding of amino group and Cl- with I- and Pb2+ ions in the perovskite, respectively. As such, the surface defects of perovskite film can be significantly reduced, leading to suppressed non-radiative recombination. Moreover, p-F-PEACl also plays a dual role in enhancing the surface potential and improving energy-level alignment at the interfaces between the perovskite and C60 carrier transport layer, which directly contributes to efficient charge extraction. Finally, the open-circuit voltage (Voc) of devices increases from 1.104 V to 1.157 V, leading to an overall efficiency improvement from 22.34% to 24.78%. Furthermore, the p-F-PEACl-treated PSCs also display excellent stability.

Self-Amplification of Coherent Energy Modulation in Seeded Free-Electron Lasers.

The spectroscopic techniques for time-resolved fine analysis of matter require coherent x-ray radiation with femtosecond duration and high average brightness. Seeded free-electron lasers (FELs), which use the frequency up-conversion of an external seed laser to improve temporal coherence, are ideal for providing fully coherent soft x-ray pulses. However, it is difficult to operate seeded FELs at a high repetition rate due to the limitations of present state-of-the-art laser systems. Here, we report a novel self-modulation method for enhancing laser-induced energy modulation, thereby significantly reducing the requirement of an external laser system. Driven by this scheme, we experimentally realize high harmonic generation in a seeded FEL using an unprecedentedly small external laser-induced energy modulation. An electron beam with a laser-induced energy modulation as small as 1.8 times the slice energy spread is used for lasing at the seventh harmonic of a 266-nm seed laser in a single-stage high-gain harmonic generation (HGHG) setup and the 30th harmonic of the seed laser in a two-stage HGHG setup. The results mark a major step toward a high-repetition-rate, fully coherent x-ray FEL.

Organic Tetrabutylammonium Cation Intercalation to Heal Inorganic CsPbI3 Perovskite.

The in situ formation of reduced dimensional perovskite layer via post-synthesis ion exchange has been an effective way of passivating organic-inorganic hybrid perovskites. In contrast, cesium ions in Cs-based inorganic perovskite with strong ionic binding energy cannot exchange with those well-known organic cations to form reduced dimensional perovskite. Herein, we demonstrate that tetrabutylammonium (TBA+ ) cation can intercalate into CsPbI3 to effectively substitute the Cs cation and to form one-dimensional (1D) TBAPbI3 layer in the post-synthesis TBAI treatment. Such TBA cation intercalation leads to in situ formation of TBAPbI3 protective layer to heal defects at the surface of inorganic CsPbI3 perovskite. The TBAPbI3 -CsPbI3 perovskite exhibited enhanced stability and lower defect density, and the corresponding perovskite solar cell devices achieved an improved efficiency up to 18.32 % compared to 15.85 % of the control one.

Steric Mixed-Cation 2D Perovskite as a Methylammonium Locker to Stabilize MAPbI3.

The reduced dimension perovskite including 2D perovskites are one of the most promising strategies to stabilize lead halide perovskite. A mixed-cation 2D perovskite based on a steric phenyltrimethylammonium (PTA) cation is presented. The PTA-MA mixed-cation 2D perovskite of PTAMAPbI4 can be formed on the surface of MAPbI3 (PTAI-MAPbI3 ) by controllable PTAI intercalation by either spin coating or soaking. The PTAMAPbI4 capping layer can not only passivate PTAI-MAPbI3 perovskite but also act as MA+ locker to inhibit MAI extraction and significantly enhance the stability. The highly stable PTAI-MAPbI3 based perovskite solar cells exhibit a reproducible photovoltaic performance with a champion PCE of 21.16 %. Such unencapsulated devices retain 93 % of initial efficiency after 500 h continuous illumination. This steric mixed-cation 2D perovskite as MA+ locker to stabilize the MAPbI3 is a promising strategy to design stable and high-performance hybrid lead halide perovskites.

2-Aminobenzenethiol-Functionalized Silver-Decorated Nanoporous Silicon Photoelectrodes for Selective CO2 Reduction.

A molecularly thin layer of 2-aminobenzenethiol (2-ABT) was adsorbed onto nanoporous p-type silicon (b-Si) photocathodes decorated with Ag nanoparticles (Ag NPs). The addition of 2-ABT alters the balance of the CO2 reduction and hydrogen evolution reactions, resulting in more selective and efficient reduction of CO2 to CO. The 2-ABT adsorbate layer was characterized by Fourier transform infrared (FTIR) spectroscopy and modeled by density functional theory calculations. Ex situ X-ray photoelectron spectroscopy (XPS) of the 2-ABT modified electrodes suggests that surface Ag atoms are in the +1 oxidation state and coordinated to 2-ABT via Ag-S bonds. Under visible light illumination, the onset potential for CO2 reduction was -50 mV vs. RHE, an anodic shift of about 150 mV relative to a sample without 2-ABT. The adsorption of 2-ABT lowers the overpotentials for both CO2 reduction and hydrogen evolution. A comparison of electrodes functionalized with different aromatic thiols and amines suggests that the primary role of the thiol group in 2-ABT is to anchor the NH2 group near the Ag surface, where it serves to bind CO2 and also to assist in proton transfer.

The Role of Dimethylammonium Iodide in CsPbI3 Perovskite Fabrication: Additive or Dopant?

The controllable growth of CsPbI3 perovskite thin films with desired crystal phase and morphology is crucial for the development of high efficiency inorganic perovskite solar cells (PSCs). The role of dimethylammonium iodide (DMAI) used in CsPbI3 perovskite fabrication was carefully investigated. We demonstrated that the DMAI is an effective volatile additive to manipulate the crystallization process of CsPbI3 inorganic perovskite films with different crystal phases and morphologies. The thermogravimetric analysis results indicated that the sublimation of DMAI is sensitive to moisture, and a proper atmosphere is helpful for the DMAI removal. The time-of-flight secondary ion mass spectrometry and nuclear magnetic resonance results confirmed that the DMAI additive would not alloy into the crystal lattice of CsPbI3 perovskite. Moreover, the DMAI residues in CsPbI3 perovskite can deteriorate the photovoltaic performance and stability. Finally, the PSCs based on phenyltrimethylammonium chloride passivated CsPbI3 inorganic perovskite achieved a record champion efficiency up to 19.03 %.

[Accuracy Verification of Robot-assisted Mandibular Reconstruction Surgery].

Mandible is an important bone of the head and neck. Mandibular defects not only affect patient's face, but also impede patient's daily functions, such as chewing, speech, and so on. Fibular transplantation for mandibular reconstruction is the common method, which requests high accuracy of bone positioning and posture adjustment. Therefore, a robotic system for mandibular reconstruction surgery with fibula flaps was designed to assist surgeons to hold and locate bones, and the model comparison experiments were conducted. The results showed that the robotic system can assist surgeons for mandibular reconstruction to improve quality of surgery.

Integrative analysis reveals ncRNA-mediated molecular regulatory network driving secondary hair follicle regression in cashmere goats.

BACKGROUND: Cashmere is a keratinized product derived from the secondary hair follicles (SHFs) of cashmere goat skins. The cashmere fiber stops growing following the transition from the actively proliferating anagen stage to the apoptosis-driven catagen stage. However, little is known regarding the molecular mechanisms responsible for the occurrence of apoptosis in SHFs, especially as pertains to the role of non-coding RNAs (ncRNAs) and their interactions with other molecules. Hair follicle (HF) degeneration is caused by localized apoptosis in the skin, while anti-apoptosis pathways may coexist in adjacent HFs. Thus, elucidating the molecular interactions responsible for apoptosis and anti-apoptosis in the skin will provide insights into HF regression. RESULTS: We used multiple-omics approaches to systematically identify long non-coding RNAs (lncRNAs), microRNAs (miRNAs) and mRNAs expressed in cashmere goat skins in two crucial phases (catagen vs. anagen) of HF growth. Skin samples were collected from three cashmere goats at the anagen (September) and catagen (February) stages, and six lncRNA libraries and six miRNA libraries were constructed for further analysis. We identified 1122 known and 403 novel lncRNAs in the goat skins, 173 of which were differentially expressed between the anagen and catagen stages. We further identified 3500 gene-encoding transcripts that were differentially expressed between these two phases. We also identified 411 known miRNAs and 307 novel miRNAs, including 72 differentially expressed miRNAs. We further investigated the target genes of lncRNAs via both cis- and trans-regulation during HF growth. Our data suggest that lncRNAs and miRNAs act synergistically in the HF growth transition, and the catagen inducer factors (TGFß1 and BDNF) were regulated by miR-873 and lnc108635596 in the lncRNA-miRNA-mRNA networks. CONCLUSION: This study enriches the repertoire of ncRNAs in goats and other mammals, and contributes to a better understanding of the molecular mechanisms of ncRNAs involved in the regulation of HF growth and regression in goats and other hair-producing species.

Demonstration of nonlinear-energy-spread compensation in relativistic electron bunches with corrugated structures.

High quality electron beams with flat distributions in both energy and current are critical for many accelerator-based scientific facilities such as free-electron lasers and MeV ultrafast electron diffraction and microscopes. In this Letter, we report on using corrugated structures to compensate for the beam nonlinear energy chirp imprinted by the curvature of the radio-frequency field, leading to a significant reduction in beam energy spread. By using a pair of corrugated structures with orthogonal orientations, we show that the quadrupole wakefields, which, otherwise, increase beam emittance, can be effectively canceled. This work also extends the applications of corrugated structures to the low beam charge (a few pC) and low beam energy (a few MeV) regime and may have a strong impact in many accelerator-based facilities.

Experimental demonstration of longitudinal beam phase-space linearizer in a free-electron laser facility by corrugated structures.

Removal of the undesired time-energy correlations in the electron beam is of paramount importance for efficient lasing of a high-gain free-electron laser. Recently, it has been theoretically and experimentally demonstrated that the longitudinal wakefield excited by the electrons themselves in a corrugated structure allows for precise control of the electron beam phase space. In this Letter, we report the first utilization of a corrugated structure as a beam linearizer in the operation of a seeded free-electron laser driven by a 140 MeV linear accelerator, where a gain of ∼10 000 over spontaneous emission was achieved at the second harmonic of the 1047 nm seed laser, and a free-electron laser bandwidth narrowing by 50% was observed, in good agreement with the theoretical expectations.

First Principles Investigation of C, Cl2 and CO Co-Adsorption on ZrSiO4 Surfaces for Carbochlorination Reaction.

The study of the adsorption behavior of C, CO and Cl2 on the surface of ZrSiO4 is of great significance for the formulation of the technological parameters in the carbochlorination reaction process. Based on first principles, the adsorption structure, adsorption energy, Barder charge, differential charge density, partial density of states and energy barrier were calculated to research the adsorption and reaction mechanism of C and Cl2 on ZrSiO4 surfaces. The results indicated that when C, CO and Cl2 co-adsorbed on the surface of ZrSiO4, they interacted with surface atoms and the charge transfer occurred. The Cl2 molecules dissociated and formed Zr-Cl bonds, while C atoms formed C1=O1 bonds with O atoms. Compared with CO, the co-adsorption energy and reaction energy barrier of C and Cl2 are lower, and the higher the C content, the lower the adsorption energy and energy barrier, which is beneficial for promoting charge transfer and the dissociation of Cl2. The 110-2C-2Cl2 has the lowest adsorption energy and the highest reaction activity, with adsorption energy and energy barriers of -13.45 eV and 0.02 eV. The electrons released by C are 2.30 e, while the electrons accepted by Cl2 are 2.37 e.

Amorphous (lysine)2PbI2 layer enhanced perovskite photovoltaics.

Passivation materials play a crucial role in a wide range of high-efficiency, high-stability photovoltaic applications based on crystalline silicon and state-of-the-art perovskite materials. Currently, for perovskite photovoltaic, the mainstream passivation strategies routinely rely on crystalline materials. Herein, we have invented a new amorphous (lysine)2PbI2 layer-enhanced halide perovskite. By utilizing a solid phase reaction between PbI2 and lysine molecule, an amorphous (lysine)2PbI2 layer is formed at surface/grain boundaries in the perovskite films. The amorphous (lysine)2PbI2 with fewer dangling bonds can effectively neutralize surface/interface defects, achieving an impressive efficiency of 26.27% (certified 25.94%). Moreover, this amorphous layer not only reduces crystal lattice stress but also functions as a barrier against the decomposition of organic components, leading to suppressed de-structuring of perovskite and highly stable perovskite solar cells.

Molecular characterization of Japanese encephalitis viruses circulating in pigs and mosquitoes on pig farms in the Chinese province of Henan.

Since the first Chinese case report of Japanese encephalitis, Japanese encephalitis virus (JEV) has circulated in China for at least 60 years. Even though pigs play a critical role in the JEV transmission cycle information on the prevalence of JEV in pigs has not been investigated in China. As the central Chinese province of Henan has the largest human population in China, a history of serious JEV and is the largest pig producing province it was chosen for this study. We have found that currently natural infection with JEV in pigs and mosquitoes is prevalent and both genotypes 1 and 3 co-circulate in pigs and mosquitoes in central China. Phylogenetic analysis showed that all of the newly obtained pig-derived JEV isolates are more closely related to isolates from the 1950s to 1960s than to those recently isolated from humans and mosquitoes. Further analyses based on all the previous reported Chinese isolates indicates that presently genotype 3 JEV is the predominant genotype in pigs but genotype 1 JEV is emerging and spreading rapidly in recent years. Our study provides information for understanding the current epidemiology of JEV in China and suggests possible measures applicable to the further control of JEV.

Functional organic cation induced 3D-to-0D phase transformation and surface reconstruction of CsPbI3 inorganic perovskite.

Efficiency and stability are the main research focuses for perovskite solar cells. Inorganic perovskites like CsPbI3 possess higher chemical stability than those with organic A-site cations, while they also exhibit higher defect density. Nonetheless, it is highly challenging to induce orderly secondary arrangement or reconstruction of inorganic perovskites with reduced defects because of their unique chemical properties. In this work, in-situ three-dimension-to-zero-dimension (3D-to-0D) phase transformation and surface reconstruction on CsPbI3 film is achieved as induced by a functional organic cation, benzyldodecyldimethylammonium (BDA), a process of which that is similar to phase-transfer catalysis. With the help of BDABr salt treatment, 0D Cs4PbI6 perovskites are secondarily formed along CsPbI3 grain boundaries with Cs-related cationic defects passivated, yielding structures of higher stability. The BDA-CsPbI3 films exhibit reduced non-radiative recombination and promoted charge transfer, leading to inorganic perovskite solar cells with a high power conversion efficiency of 20.63% and good operational stability.

Solution chemistry quasi-epitaxial growth of atomic CaTiO3 perovskite layers to stabilize and passivate TiO2 photoelectrodes for efficient water splitting.

Perovskite oxides with unique crystal structures and high defect tolerance are promising as atomic surface passivation layers for photoelectrodes for efficient and stable water splitting. However, controllably depositing and crystalizing perovskite-type metal oxides at the atomic level remains challenging, as they usually crystalize at higher temperatures than regular metal oxides. Here, we report a mild solution chemistry approach for the quasi-epitaxial growth of an atomic CaTiO3 perovskite layer on rutile TiO2 nanorod arrays. The high-temperature crystallization of CaTiO3 perovskite is overcome by a sequential hydrothermal conversion of the atomic amorphous TiOx layer to CaTiO3 perovskite. The atomic quasi-epitaxial CaTiO3 layer passivated TiO2 nanorod arrays exhibit more efficient interface charge transfer and high photoelectrochemical performance for water splitting. Such a mild solution-based approach for the quasi-epitaxial growth of atomic metal oxide perovskite layers could be a promising strategy for both fabricating atomic perovskite layers and improving their photoelectrochemical properties.

A Review of Robotic Fish Based on Smart Materials.

The present study focuses on summarizing the recent advancements in the field of fish swimming mode research and bionic robotic fish prototypes based on smart materials. It has been widely acknowledged that fish exhibit exceptional swimming efficiency and manoeuvrability compared to conventional underwater vehicles. In the pursuit of developing autonomous underwater vehicles (AUVs), conventional experimental methods often prove to be complex and expensive. Hence, the utilization of computer simulations for hydrodynamic modelling provides a cost-effective and efficient approach for analysing the swimming behaviour of bionic robotic fish. Additionally, computer simulations can provide data that are difficult to obtain through experimental methods. Smart materials, which integrate perception, drive, and control functions, are increasingly being applied to bionic robotic fish research. However, the utilization of smart materials in this field is still an area of ongoing research and several challenges remain unresolved. This study provides an overview of the current state of research on fish swimming modes and the development of hydrodynamic modelling. The application of four distinct types of smart materials in bionic robotic fish is then reviewed, with a focus on analysing the advantages and disadvantages of each material in driving swimming behaviour. In conclusion, the paper highlights the key technical challenges that must be addressed for the practical implementation of bionic robotic fish and provides insights into the potential future directions of this field.

Post-Treatment-Free Dual-Interface Passivation via Facile 1D/3D Perovskite Heterojunction Construction.

For achieving high-efficiency perovskite solar cells, it is almost always necessary to substantially passivate defects and protect the perovskite structure at its interfaces with charge transport layers. Such a modification generally involves the post-treatment of the deposited perovskite film by spin coating, which cannot meet the technical demands of scaling up the production of perovskite photovoltaics. In this work, we demonstrate one-step construction of buried and capped double 1D/3D heterojunctions without the need for any post-treatment, which is achieved through facile tetraethylammonium trifluoroacetate (TEATFA) prefunctionalization on the SnO2 substrate. The functional TEATFA salt is first deposited onto the SnO2 substrate and reacts on this buried interface. Once the FAPbI3 perovskite precursor solution is dripped, a portion of the TEA+ cations spontaneously diffuse to the top surface over film crystallization. The TEATFA-based water-resistant 1D/3D TEAPbI3/FAPbI3 heterojunctions at both the buried and capped interfaces lead to much better photovoltaic performance and higher operational stability. Since this approach saves the need for any postsynthesis passivation, its feasibility for the fabrication of large-area perovskite photovoltaics is also showcased. Compared to ∼15% for a pristine 5 cm × 5 cm FAPbI3 mini-module without postsynthesis passivation, over 20% efficiency is achieved following the proposed route, demonstrating its great potential for larger-scale fabrication with fewer processing steps.

Modulation of Charge Transport from Two-Dimensional Perovskites to Industrial Charge Transport Layers by the Organic Spacer-Dependent Exciton-Phonon Interactions.

In the past decade, two-dimensional (2D) perovskite surface treatment has emerged as a promising strategy to improve the performance of three-dimensional (3D) perovskite solar cells (PSCs). However, systematic studies on the impact of organic spacers of 2D perovskites on charge transport in 2D/3D PSCs are still lacking. Here, using 2D perovskite film/C60 heterostructures with different organic spacers [butylamine (BA), phenylethylamine (PEA), and 3-fluorophenethylamine (m-F-PEA)], we systematically investigated the carrier diffusion and interfacial transfer process. Using a 2D perovskite film with a thickness of ∼7 nm, we observed subtle differences in electron transfer time between 2D perovskites and C60 layers, which can be attributed to limited thickness and similar electron coupling strength. However, with the thickness of 2D perovskite increasing, electron transfer efficiency in the (BA)2PbI4/C60 heterostructure exhibits the most rapid decrease due to poor carrier diffusion of (BA)2PbI4 caused by stronger exciton-phonon interactions compared to (PEA)2PbI4 and (m-F-PEA)2PbI4 in thickness-dependent charge transfer research. Meanwhile, the fill factor of 2D/3D PSC treated with BAI exhibits the most rapid decrease compared to PEAI- and m-F-PEAI-treated 2D/3D PSCs with the concentration increase of passivators. This study indicates that it is easier to enhance open-circuit voltages and minimize the decrease of fill factor by increasing the concentration of passivators in 2D/3D PSCs when using passivators with a rigid molecular structure.

Hot Deformation Behavior of the 25CrMo4 Steel Using a Modified Arrhenius Model.

25CrMo4 steel is widely used in the manufacturing of high-speed train axles due to its excellent mechanical properties. The purpose of this study is to develop an accurate modified constitutive model to describe the hot deformation behavior of the steel. Isothermal compression experiments were performed at different strain rates (0.01, 0.1, 0.5, and 1 s-1) and different temperatures (950, 1000, 1050, and 1100 °C) using a Gleeble-3800 thermal simulator. The microstructure after hot deformation was observed by the electron backscatter diffraction (EBSD), and the effects of temperature and strain rate were analyzed. The results showed that the coupling effect of temperature and strain rate on the dislocation density led to the change in the shape of the true stress-strain curve and that dynamic recovery (DRV) and dynamic recrystallization (DRX) caused the macroscopic softening phenomenon, with DRX being the main mechanism. Based on the true stress-strain curves, the strain-compensated Arrhenius constitutive model was calibrated. To improve prediction ability, a modified Arrhenius constitutive model was proposed, in which the temperature and strain rate coupling correction functions were incorporated. The original, modified Arrhenius models were evaluated according to the absolute relative error (ARE), the average absolute relative error (AARE), and the correlation coefficient (R2). Compared with the original model, the modified Arrhenius model has a higher prediction accuracy, with the ARE value mostly below 4%, the AARE value of 1.91%, and the R2 value of 0.9958.