Engineering Tough Supramolecular Hydrogels with Structured Micropillars for Tunable Wetting and Adhesion Properties.

Soft-lithography is widely used to fabricate microstructured surfaces on plastics and elastomers for designable physical properties such as wetting and adhesions. However, it remains a big challenge to construct high-aspect-ratio microstructures on the surface of hydrogels due to the difficulty in demolding from the gel with low strength and stiffness. Demonstrated here is the engineering of tough hydrogels by soft-lithography to form well-defined micropillars. The mechanical properties of poly(acrylamide-co-methacrylic acid) hydrogels with dense hydrogen-bond associations severely depend on temperature, with Young's modulus increasing from 8.1 MPa at 15 °C to 821.8 MPa at -30 °C, enabling easy demolding at low temperatures. Arrays of micropillars are maintained on the surface of the gel, and can be used at room temperature when the gel restores soft and stretchable. The hydrogel also exhibits good shape-memory property, favoring tailoring the morphology with a switchable tilt angle of micropillars. Consequently, the hydrogel shows tunable wetting and adhesion properties, as manifested by varying contact angles and adhesion strengths. These surface properties can also be tuned by geometry and arrangement of micropillars. This facile strategy by harnessing tunable viscoelasticity of supramolecular hydrogels should be applicable to other soft materials, and broaden their applications in biomedical and engineering fields.

Polymerization-Induced Crystallization of Dopant Molecules: An Efficient Strategy for Room-Temperature Phosphorescence of Hydrogels.

Conventional hydrogels such as polyacrylamide and polyacrylic acid ones seldom exhibit phosphorescences at ambient conditions, which limit their applications as optical materials. We propose and demonstrate here a facile strategy to afford these hydrogels with room-temperature phosphorescence by polymerization-induced crystallization of dopant molecules that results in segregation and confinement of the gel matrix with carbonyl groups and thus clusterization-induced phosphorescence. As a model system, crown ethers (CEs) are dissolved in an aqueous solution of concentrated acrylamide that greatly increases the solubility of CEs. During the polymerization process, CEs crystallize to form large spherulites in the polyacrylamide hydrogel. The crystallization arises from the drastically reduced solubility of CEs after the conversion of monomers to polymers during the gel synthesis. The resultant composite hydrogel with a water content of 67 wt % exhibits extraordinary phosphorescence behavior yet maintains good stretchability and resilience. We found that the partial gel matrix is squeezed and confined by in situ-formed crystals, leading to carbonyl clusters and thus phosphorescence emission. The composite gel shows green phosphorescence with an emission peak at 512 nm and a lifetime of 342 ms. The afterglow emission is detectable by the naked eye for several seconds. This strategy has good universality, as validated in other hydrogels with different polymeric matrices and dopant molecules. The development of hydrogels with good mechanical and phosphorescent properties should merit the design of multifunctional soft machines with applications in biomedical and engineering fields.

Programmable Morphing Hydrogels for Soft Actuators and Robots: From Structure Designs to Active Functions.

Nature provides abundant inspiration and elegant paradigms for the development of smart materials that can actuate, morph, and move on demand. One remarkable capacity of living organisms is to adapt their shapes or positions in response to stimuli. Programmed deformations or movements in plant organs are mainly driven by water absorption/dehydration of cells, while versatile motions of mollusks are based on contraction/extension of muscles. Understanding the general principles of these morphing and motion behaviors can give rise to disruptive technologies for soft robotics, flexible electronics, biomedical devices, etc. As one kind of intelligent material, hydrogels with high similarity to soft biotissues and diverse responses to external stimuli are an ideal candidate to construct soft actuators and robots.The objective of this Account is to give an overview of the fundamental principles for controllable deformations and motions of hydrogels, with a focus on the structure designs and responsive functions of the corresponding soft actuators and robots. This field has been rapidly developed in recent years with a growing understanding of working principles in natural organisms and a substantial revolution of manufacturing technologies to devise bioinspired hydrogel systems with desired structures. Diverse morphing hydrogels and soft actuators/robots have been developed on the basis of several pioneering works, ranging from bending and folding deformations of bilayer hydrogels to self-shaping of non-Euclidean hydrogel surfaces, and from thermoactuated bilayer gel "hands" to electrodriven polyelectrolyte gel "worms". These morphing hydrogels have demonstrated active functions and versatile applications in biomedical and engineering fields.In this Account, we discuss recent progress in morphing hydrogels and highlight the design principles and relevant applications. First, we introduce the fundamentals of basic deformation modes, together with generic structure features, actuation strategies, and morphing mechanisms. The advantages of in-plane gradient structures are highlighted for programmable deformations by harnessing the out-of-plane buckling with bistability nature to obtain sophisticated three-dimensional configurations. Next, we give an overview of soft actuators and robots based on morphing hydrogels and focus on the working principles of the active systems with different structure designs. We discuss the advancements of hydrogel-based soft robots capable of swift locomotion with different gaits and emphasize the significances of structure control and dynamic actuation. Then we summarize versatile applications of hydrogel-based actuators and robots in biomedicines, cargo delivery, soft electronics, information encryption, and so forth. Some hydrogel robots with a built-in feedback loop and self-sensing system exhibit collaborative functions and advanced intelligence that are informative for the design of next-generation hydrogel machines. Finally, concluding remarks are given to discuss future opportunities and remaining challenges in this field. For example, miniature hydrogel-based actuators/robots with therapeutic or diagnostic functions are highly desired for biomedical applications. The morphing mechanisms summarized in this Account should be applicable to other responsive materials. We hope that this Account will inspire more scientists to be involved in this emerging area and make contributions to reveal novel working principles, design multifunctional soft machines, and explore applications in diverse fields.

Toughening Hydrogels by Forming Robust Hydrazide-Transition Metal Coordination Complexes.

Energy dissipation based on dynamic fracture of metal ligands is an effective way to toughen hydrogels for specific applications in biomedical and engineering fields. Exploration of new kinds of metal-ligand coordinates with robust bonding strength is crucial for the facile synthesis of tough gels. Here a hydrogel toughening strategy based on the formation of robust coordination complexes between the hydrazide ligands and zinc ions is reported. The resultant hydrogels exhibit high strength and toughness at room temperature. Their mechanical properties show temperature dependence due to the dynamic nature of coordination bonds. In addition, the amine group of hydrazides in the gel matrix provides a reactive site for Schiff's base reaction, enabling surface modification without influence on overall mechanical performances of the gel. The hydrazide ligands are easy to synthesize and can coordinate very well with several transition metals. Such a metal-ligand coordination should be suitable to develop tough soft materials with versatile applications.

Healable, Recyclable, and Multifunctional Soft Electronics Based on Biopolymer Hydrogel and Patterned Liquid Metal.

Recent years have witnessed the rapid development of sustainable materials. Along this line, developing biodegradable or recyclable soft electronics is challenging yet important due to their versatile applications in biomedical devices, soft robots, and wearables. Although some degradable bulk hydrogels are directly used as the soft electronics, the sensing performances are usually limited due to the absence of distributed conducting circuits. Here, sustainable hydrogel-based soft electronics (HSE) are reported that integrate sensing elements and patterned liquid metal (LM) in the gelatin-alginate hybrid hydrogel. The biopolymer hydrogel is transparent, robust, resilient, and recyclable. The HSE is multifunctional; it can sense strain, temperature, heart rate (electrocardiogram), and pH. The strain sensing is sufficiently sensitive to detect a human pulse. In addition, the device serves as a model system for iontophoretic drug delivery by using patterned LM as the soft conductor and electrode. Noncontact detection of nearby objects is also achieved based on electrostatic-field-induced voltage. The LM and biopolymer hydrogel are healable, recyclable, and degradable, favoring sustainable applications and reconstruction of the device with new functions. Such HSE with multiple functions and favorable attributes should open opportunities in next-generation electronic skins and hydrogel machines.

Multi-level encryption of information in morphing hydrogels with patterned fluorescence.

Fluorescent hydrogels have attracted tremendous attention recently in the field of information security due to the booming development of information technology. Along this line, it is highly desired to improve the security level of concealed information by the advancements of materials and encryption technologies. Here we report multi-level encryption of information in a bilayer hydrogel with shape-morphing ability and patterned fluorescence. This hydrogel is composed of a fluorescence layer containing chromophore units in the poly(acrylic acid) network and an active layer with UV-absorption agents in the poly(N-isopropylacrylamide-co-acrylic acid) network. The former layer exhibits tunable fluorescence tailored by UV light irradiation to induce unimer-to-dimer transformation of the chromophores, facilitating the write-in of information through photolithography. The latter layer is responsive to temperature, enabling morphing of the bilayer hydrogel. Therefore, the bilayer hydrogel encoded with patterned fluorescent patterns can deform into three-dimensional configurations at room temperature to conceal the information, which is readable only after successive procedures of shape recovery at an appropriate temperature and under UV light irradiation from the right direction. The combination of morphing materials and patterned fluorescence as a new avenue to improve the encryption level of information should merit the design of other smart materials with integrated functions for specific applications.

Magneto-Orientation of Magnetic Double Stacks for Patterned Anisotropic Hydrogels with Multiple Responses and Modulable Motions.

Reported here is a multi-response anisotropic poly(N-isopropylacrylamide) hydrogel developed by using a rotating magnetic field to align magnetic double stacks (MDSs) that are fixed by polymerization. The magneto-orientation of MDSs originates from the unique structure with γ-Fe2 O3 nanoparticles sandwiched by two silicate nanosheets. The resultant gels not only exhibit anisotropic optical and mechanical properties but also show anisotropic responses to temperature and light. Gels with complex ordered structures of MDSs are further devised by multi-step magnetic orientation and photolithographic polymerization. These gels show varied birefringence patterns with potentials as information materials, and can deform into specific configurations upon stimulations. Multi-gait motions are further realized in the patterned gel through dynamic deformation under spatiotemporal light and friction regulation by imposed magnetic force. The magneto-orientation assisted fabrication of hydrogels with anisotropic structures and additional functions should bring opportunities for gel materials in biomedical devices, soft actuators/robots, etc.

Engineering Tough Metallosupramolecular Hydrogel Films with Kirigami Structures for Compliant Soft Electronics.

A simple and effective approach is demonstrated to fabricate tough metallosupramolecular hydrogel films of poly(acrylic acid) by one-pot photopolymerization of the precursor solution in the presence of Zr4+ ions that form coordination complexes with the carboxyl groups and serve as the physical crosslinks of the matrix. Both as-prepared and equilibrated hydrogel films are transparent, tough, and stable over a wide range of temperature, ionic strength, and pH. The thickness of the films can be easily tailored with minimum value of ≈7 µm. Owing to the fast polymerization and gelation process, kirigami structures can be facilely encoded to the gel films by photolithographic polymerization, affording versatile functions such as additional stretchability and better compliance of the planar films to encapsulate objects with sophisticated geometries that are important for the design of soft electronics. By stencil printing of liquid metal on the hydrogel film with a kirigami structure, the integrated soft electronics shows good compliance to cover curved surfaces and high sensitivity to monitor human motions. Furthermore, this strategy is applied to diverse natural and synthetic macromolecules containing carboxyl groups to develop tough hydrogel films, which will open opportunities for the applications of hydrogel films in biomedical and engineering fields.

Sequentially Controlled Deformations of Patterned Hydrogels into 3D Configurations with Multilevel Structures.

Sequential deformations of patterned hydrogels into 3D configurations with multilevel structures are reported, which are realized for the first time in self-shaping materials. The periodically patterned single-layer hydrogels with different polymers are fabricated by multi-step photolithography. After swelling in water, the expansion of compartmentalized high-swelling gels is constrained by the dispersed non-swelling gels, resulting in out-of-plane buckling with high cooperativity and thus forming alternating concave-convex configuration. When the dispersed non-swelling gels are partly replaced by thermoresponsive ones, the preformed overall flat, yet locally undulant, hydrogel deforms further into dome-, saddle-, or sandglass-like configurations at elevated temperature. As such, multilevel 3D structures can be achieved via prebuilt mechanical/geometric cues in a sequentially controlled manner. This conceptual design and sequential deformation of patterned hydrogels to form 3D configurations with multilevel structures should enrich the deformation/functioning modes of morphing materials and broaden their applications in diverse areas.

Kinetic Insights into Marangoni Effect-Assisted Preparation of Ultrathin Hydrogel Films.

In a previous work ( ACS Appl. Mater. Interfaces 2017, 9, 34349-34355), a facile approach was reported to prepare thin hydrogel films based on the Marangoni effect. After dripping onto a water surface, a drop of ethanol solution of poly(stearyl acrylate- co-acrylic acid) [P(SA- co-AAc)] spread quickly to form a thin film. The solvent exchange from ethanol to water led to the gelation of polymer solution which turned into a hydrogel film. Here, we investigate the scenario and seek for the governing kinetics of the Marangoni effect-assisted preparation of hydrogel films. By incorporating aggregation-induced emission fluorogens into the P(SA- co-AAc) solution, so that fluorescence appears at the gel state, we found that the spreading usually completed before the full gelation of the entire film. The spreading and formation of the gel films were influenced by the molar fraction of SA, f, and the polymer concentration of ethanol solution, CP. The spreading was blocked when CP was too high, whereas the film was fragmented into small pieces when CP was too low. At an intermediate CP, uniform hydrogel films were obtained. Steady spreading at a constant speed was observed during the processes which yielded uniform hydrogel films. Both CP and f influenced the spreading process by tuning the surface tension of the ethanol solution and the viscoelasticity of the gelated film, as suggested by our theoretical model. This work provided kinetic insights into the Marangoni phenomena of viscous polymer solutions. The strategy and principle should be applicable to other systems on preparing thin supramolecular gel films with versatile functions.

Spin-coating-assisted fabrication of ultrathin physical hydrogel films with high toughness and fast response.

Hydrogel films have promising applications in medical dressings, flexible electronics, etc. However, it is challenging to fabricate ultrathin hydrogel films with high toughness and controllable thickness. Here, we report a facile approach to prepare tough physical hydrogel films by spin-coating of a poly(acrylic acid-co-acrylamide) (P(AAc-co-AAm)) solution and subsequent gelation in FeCl3 solution to form carboxyl-Fe3+ coordination complexes. The thickness of the obtained gel films, ranging from several to hundreds of micrometers, was easily tunable by adjusting the spin conditions and polymer concentration. The thus obtained hydrogel films showed excellent mechanical properties, with tensile breaking strengths of 0.6-14.5 MPa, breaking strains of 140-840%, Young's moduli of 0.1-61.7 MPa, and tearing fracture energies of 300-1300 J m-2. Based on this approach, responsive tough hydrogel films can also be prepared by spin-coating of a poly(acrylic acid-co-N-isopropylacrylamide) (P(AAc-co-NIPAm)) solution. The obtained gel films showed a fast response (<60 s) and a large output force (∼0.2 MPa) triggered by a concentrated saline solution, making them an ideal material in the design of chemomechanical devices. Furthermore, a bilayer hydrogel film was fabricated by two-step spin-coating of P(AAc-co-NIPAm) and P(AAc-co-AAm) solutions, which showed reversible bending deformation under external stimuli. This simple yet effective approach should be applicable to other systems to prepare versatile hydrogel films with tunable thickness and promising applications in diverse areas.

Catenane Crosslinked Mechanically Adaptive Polymer Gel.

A new strategy is introduced to prepare an adaptive polymer gel that has a unique adaptability in response to environmental stimuli. This gel is prepared by the thiol-ene "click" reaction between a bisvinyl [2]catenane and a poly(ethylene glycol) derivative containing multiple thiol groups. The catenane crosslinker is responsive to external stimuli due to the existence of intercomponent hydrogen bonding (IHB). The strong IHB restricts the rotation and movement of the crosslinker, giving it a rigid feature; however, the crosslinker becomes flexible when the IHB is destroyed. In consequence, the resulting gel can be reversibly switched between tough and soft states under stimulations.

Dual-Crosslink Physical Hydrogels with High Toughness Based on Synergistic Hydrogen Bonding and Hydrophobic Interactions.

Constructing dual or multiple noncovalent crosslinks is highly effective to improve the mechanical and stimuli-responsive properties of supramolecular physical hydrogels, due to the synergistic effects of different noncovalent bonds. Herein, a series of tough physical hydrogels are prepared by solution casting and subsequently swelling the films of poly(ureidopyrimidone methacrylate-co-stearyl acrylate-co-acrylic acid). The hydrophobic interactions between crystallizable alkyl chains and the quadruple hydrogen bonds between ureidopyrimidone (UPy) motifs serve as the dual crosslinks of hydrogels. Synergistic effects between the hydrophobic interactions and hydrogen bonds render the hydrogels excellent mechanical properties, with tensile breaking stress up to 4.6 MPa and breaking strain up to 680%. The UPy motifs promote the crystallization of alkyl chains and the hydrophobic alkyl chains also stabilize UPy-UPy hydrogen bonding. The resultant hydrogels are responsive to multiple external stimuli, such as temperature, pH, and ion; therefore, they show the thermal-induced dual and metal ion-induced triple shape memory behaviors.

Stereocomplexed physical hydrogels with high strength and tunable crystallizability.

Physical hydrogels crosslinked by non-covalent interactions have attained increasing attention due to their good mechanical properties and processability. However, the use of feasible and controllable non-covalent interactions is highly essential for preparing such hydrogels. In this article, we report on stereocomplexed physical hydrogels prepared by simple casting and swelling of amphiphilic graft copolymers bearing a poly(acrylic acid) (PAA) backbone and poly(l-lactic acid) (PLLA) or poly(d-lactic acid) (PDLA) stereocomplexable side chains. The microstructure, swelling behavior, and mechanical and shape memory properties of the obtained hydrogels can be tuned by varying the copolymer composition and stereocomplex (SC) crystallization of PLLA/PDLA enantiomeric chains. The long PLLA or PDLA chains segregate to form hydrophobic, crystallized domains in water, serving as physical crosslinking junctions for hydrogels. SC crystallization between PLLA and PDLA further enhances the number density of physical crosslinkers of enantiomerically mixed hydrogels. The SC content increases as the PLLA/PDLA ratio approaches 1/1 in enantiomerically mixed hydrogels. The average distance between crosslinking junctions declines for the hydrogels with a high PLLA (or PDLA) mass fraction (MPLA) and SC content, due to the increased number density of physical crosslinkers. Accordingly, the tensile strength and the Young's modulus increase but the swelling ratio and the elongation-at-break of the hydrogels decrease with an increase in MPLA and SC content. The hydrogels exhibit shape memory behavior; the shape fixing ability is enhanced by the SC crystallization of PLLA/PDLA side chains in the hydrogels.

Ultrastiff Hydrogels Prepared by Schiff's Base Reaction of Bis(p-Formylphenyl) Sebacate and Pillar[5]arene Appended with Multiple Hydrazides.

Herein a facile method is reported to prepare polymer gels based on the formation of acylhydrazone bond under mild conditions. A pillar[5]arene derivative appended with ten hydrazide groups provides multiple sites for the reaction with the aldehyde groups of bis(p-formylphenyl) sebacate in the presence of a small amount of HCl as the catalyst in dimethyl sulfoxide (DMSO), producing transparent polymer organogels. The mechanical properties of gels can be easily tuned by the molar ratio of the reactant compounds. After solvent exchange from DMSO to water, translucent polymer hydrogels with dramatically enhanced strength and stiffness are obtained. The tensile breaking stress and Young's modulus of hydrogels are 20-60 and 1.2-2.7 MPa, respectively, 100 and 20 times those of the corresponding organogels. These robust hydrogels with ultrahigh stiffness should find applications such as in load-bearing artificial organs. This work should merit designing functional materials using other macrocycles.

Site-Specific Pre-Swelling-Directed Morphing Structures of Patterned Hydrogels.

Morphing materials have promising applications in various fields, yet how to program the self-shaping process for specific configurations remains a challenge. Herein we show a versatile approach to control the buckling of individual domains and thus the outcome configurations of planar-patterned hydrogels. By photolithography, high-swelling disc gels were positioned in a non-swelling gel sheet; the swelling mismatch resulted in out-of-plain buckling of the disc gels. To locally control the buckling direction, masks with holes were used to guide site-specific swelling of the high-swelling gel under the holes, which built a transient through-thickness gradient and thus directed the buckling during the subsequent unmasked swelling process. Therefore, various configurations of an identical patterned hydrogel can be programmed by the pre-swelling step with different masks to encode the buckling directions of separate domains.

Thermoresponsive physical hydrogels of poly(lactic acid)/poly(ethylene glycol) stereoblock copolymers tuned by stereostructure and hydrophobic block sequence.

CBABC-type poly(lactic acid) (PLA)/poly(ethylene glycol) (PEG) pentablock copolymers composed of a central PEG block (A) and enantiomeric poly(l-lactic acid) (PLLA, B), poly(d-lactic acid) (PDLA, C) blocks were synthesized. Such pentablock copolymers form physical hydrogels at high concentrations in an aqueous solution, which stem from the aggregation and physical bridging of copolymer micelles. These gels are thermoresponsive and turn into sols upon heating. Physical gelation, gel-to-sol transition, crystalline state, microstructure, rheological behavior, biodegradation, and drug release behavior of PLA/PEG pentablock copolymers and their gels were investigated; they were also compared with PLA-PEG-PLA triblock copolymers containing the isotactic PLLA or atactic poly(d,l-lactide) (PDLLA) endblocks and PLLA-PEG-PLLA/PDLA-PEG-PDLA enantiomeric mixtures. PLA hydrophobic domains in pentablock copolymer gels changed from a homocrystalline to stereocomplexed structure as the PLLA/PDLA block length ratio approached 1/1. The gel of symmetric pentablock copolymer exhibited a wider gelation region, higher gel-to-sol transition temperature, higher hydrophobic domain crystallinity, larger intermicellar distance, higher storage modulus, and slower degradation and drug release rate compared to those of the asymmetric PLA/PEG pentablock copolymers or triblock copolymers. SAXS results indicated that the PLLA/PDLA blocks stereocomplexation in pentablock copolymers facilitated the intermicellar aggregation and bridging. Cylindrical ordered structures were observed in all the gels formed from the PLA/PEG pentablock and triblock copolymers. The stereocomplexation degree and intermicellar distance of the pentablock copolymer gels increased with heating.

Light Responsive Microstructured Surfaces of Liquid Crystalline Network with Shape Memory and Tunable Wetting Behaviors.

Using adaptive soft materials to fabricate microstructured surfaces renders them with tunable topographic feature and thus controllable physical properties. Here, light responsive microstructured surfaces are reported with shape memory and tunable wetting behaviors; the surfaces are covered with micropillar arrays and constructed by lightly crosslinked azo-containing liquid crystalline network (LCN). UV light irradiation induces 25% contraction in length of the micropillars along their long axes and, as a consequence, the variations of topographic feature and wetting behavior of the surfaces. In addition, the LCNs exhibit shape memory properties, which can freeze the temporary topographic feature of microstructured surfaces (formed under UV irradiation and relatively high temperature) and enable application of their functionalities at mild conditions. This light responsiveness makes it feasible to remotely and precisely tune the local regions of microstructured surfaces, which should broaden the applications of adaptive surfaces in regulating the wetting, optical, and adhesion properties in selected regions.

Animating hydrogel knotbots with topology-invoked self-regulation.

Steering soft robots in a self-regulated manner remains a grand challenge, which often requires continuous symmetry breaking and recovery steps for persistent motion. Although structural morphology is found significant for robotic functions, geometric topology has rarely been considered and appreciated. Here we demonstrate a series of knotbots, namely hydrogel-based robots with knotted structures, capable of autonomous rolling and spinning/rotating motions. With symmetry broken by external stimuli and restored by self-regulation, the coupling between self-constraint-induced prestress and photothermal strain animates the knotbots continuously. Experiments and simulations reveal that nonequilibrium processes are regulated dynamically and cooperatively by self-constraints, active deformations, and self-shadowing effect of the photo-responsive gel. The active motions enable the knotbots to execute tasks including gear rotation and rod climbing. This work paves the way to devise advanced soft robots with self-regulated sustainable motions by harnessing the topology.

Photo-steered rapid and multimodal locomotion of 3D-printed tough hydrogel robots.

Hydrogels are an ideal material to develop soft robots. However, it remains a grand challenge to develop miniaturized hydrogel robots with mechanical robustness, rapid actuation, and multi-gait motions. Reported here is a facile strategy to fabricate hydrogel-based soft robots by three-dimensional (3D) printing of responsive and nonresponsive tough gels for programmed morphing and locomotion upon stimulations. Highly viscoelastic poly(acrylic acid-co-acrylamide) and poly(acrylic acid-co-N-isopropyl acrylamide) aqueous solutions, as well as their mixtures, are printed with multiple nozzles into 3D constructs followed by incubation in a solution of zirconium ions to form robust carboxyl-Zr4+ coordination complexes, to produce tough metallo-supramolecular hydrogel fibers. Gold nanorods are incorporated into ink to afford printed gels with response to light. Owing to the mechanical excellence and small diameter of gel fibers, the printed hydrogel robots exhibit high robustness, fast response, and agile motions when remotely steered by dynamic light. The design of printed constructs and steering with spatiotemporal light allow for multimodal motions with programmable trajectories of the gel robots. The hydrogel robots can walk, turn, flip, and transport cargos upon light stimulations. Such printed hydrogels with good mechanical performances, fast response, and agile locomotion may open opportunities for soft robots in biomedical and engineering fields.