Investigation on pulse shaping in fiber laser hybrid mode-locked by Sb(2)Te(3) saturable absorber.

We report a study on a hybrid mode-locked fiber laser with two saturable absorbers: slow and fast, integrated in a single device. Amorphous antimony telluride (Sb(2)Te(3)) layer was deposited on side-polished fiber to form the slow saturable absorber due to the third order nonlinear susceptibility of Sb(2)Te(3). Additionally, an unsymmetrical design of the device causes polarization-dependent losses and together with polarization controller allows to use a nonlinear polarization evolution to form the artificial fast saturable absorber. Sub-200 fs soliton pulses with 0.27 nJ of pulse energy were generated in the hybrid mode-locked Er-doped fiber laser. Differences in the dynamics of mode-locked laser are further investigated with the use of slow and fast saturable absorbers solely, and compared with the hybrid device. Joint operation of two saturable absorbers enhances the laser performance and stability. The conducted experiments allowed to define roles of each mechanism on the pulse shaping in the laser cavity.

Dissipative soliton generation in Er-doped fiber laser mode-locked by Sb2Te3 topological insulator.

We report on the generation of dissipative solitons in an Er-doped fiber laser mode-locked by antimony telluride (Sb 2 Te 3) topological insulator in the near-zero dispersion regime. Layers of Sb 2 Te 3 were deposited on a side-polished (D-shaped) fiber using a pulsed magnetron sputtering technique. Sub-170-fs pulses with 34-nm full width at half-maximum (FWHM) and 0.21 nJ of pulse energy were obtained from an all-fiber, ring-shaped laser cavity after the compression in a single-mode fiber.

Corrosion Behavior of Ferritic 12Cr ODS and Martensitic X46Cr13 Steels in Nitric Acid and Sodium Chloride Solutions.

This paper presents corrosion resistance results of a 12Cr ferritic ODS steel (Fe-12Cr-2W-0.5Zr-0.3Y2O3) fabricated via a powder metallurgy route as a prospective applicant for fuel cladding materials. In a spent nuclear fuel reprocessing facility, nitric acid serves as the primary solvent in the PUREX method. Therefore, fundamental immersion and electrochemical tests were conducted in various nitric acid solutions to evaluate corrosion degradation behavior. Additionally, polarization tests were also performed in 0.61 M of sodium chloride solutions (seawater-like atmosphere) as a more general, all-purpose procedure that produces valid comparisons for most metal alloys. For comparison, martensitic X46Cr13 steel was also examined under the same conditions. In general, the corrosion resistance of the 12Cr ODS steel was better than its martensitic counterpart despite a lower nominal chromium content. Potentiodynamic polarization plots exhibited a lower corrosion current and higher breakdown potentials in chloride solution in the case of the ODS steel. It was found that the corrosion rate during immersion tests was exceptionally high in diluted (0.1-3 M) boiling nitric acid media, followed by its sharp decrease in more concentrated solutions (>4 M). The results of the polarization plots also exhibited a shift toward more noble corrosion potential as the concentrations increased from 1 M to 4 M of HNO3. The results on corrosion resistance were supported by LSCM and SEM observations of surface topology and corrosion products.

Using the Spark Plasma Sintering System for Fabrication of Advanced Semiconductor Materials.

The interest in the Spark Plasma Sintering (SPS) technique has continuously increased over the last few years. This article shows the possibility of the development of an SPS device used for material processing and synthesis in both scientific and industrial applications and aims to present manufacturing methods and the versatility of an SPS device, presenting examples of processing Arc-Melted- (half-Heusler, cobalt triantimonide) and Self-propagating High-temperature Synthesis (SHS)-synthesized semiconductor (bismuth telluride) materials. The SPS system functionality development is presented, the purpose of which was to broaden the knowledge of the nature of SPS processes. This approach enabled the precise design of material sintering processes and also contributed to increasing the repeatability and accuracy of sintering conditions.

Microstructure and Corrosion of Mg-Based Composites Produced from Custom-Made Powders of AZ31 and Ti6Al4V via Pulse Plasma Sintering.

Magnesium (Mg) and its alloys offer promise for aerospace, railway, and 3D technology applications, yet their inherent limitations, including inadequate strength, pose challenges. Magnesium matrix composites, particularly with metallic reinforcements like titanium (Ti) and its alloys, present a viable solution. Therefore, this study investigates the impact of Ti6Al4V reinforcement on AZ31 magnesium alloy composites produced using pulse plasma sintering (PPS). Results show enhanced microhardness of the materials due to improved densification and microstructural refinement. However, Ti6Al4V addition decreased corrosion resistance, leading to strong microgalvanic corrosion and substrate dissolution. Understanding these effects is crucial for designing Mg-based materials for industries like petrochemicals, where degradation-resistant materials are vital for high-pressure environments. This research provides valuable insights into developing Mg-Ti6Al4V composites with tailored properties for diverse industrial applications, highlighting the importance of considering corrosion behavior in material design. Further investigation is warranted to establish predictive correlations between Ti6Al4V content and corrosion rate for optimizing composite performance.

Formation and Microstructural Evolution of Ferritic ODS Steel Powders during Mechanical Alloying.

Ferritic ODS steel elemental powder compositions with various Zr content (0.3-1.0 wt.%), ground in a Pulverisette 6 planetary ball mill, were extensively studied by X-ray diffraction line profile analysis, microscopic observations, microhardness testing and particle size measurements. A characteristic three-stage process of flattening the soft powders, formation of convoluted lamellae and, finally, formation of nanocrystalline grains was observed. In order to quantify the microstructural properties, expressed mainly in terms of crystallite size and dislocation density, a methodology for detailed and accurate microstructure analysis of nanosized and severely deformed materials was proposed by the Whole Powder Pattern Modelling (WPPM) approach. In the case of the proposed ODS alloy composition, the overlapping of Fe and Cr Bragg reflections makes the microstructure analysis certainly more complicated. The results showed that the microstructure of powders evolved towards the nanocrystalline state consisting of fine (diameter of ~15 nm) and narrowly dispersed domains, with extensive dislocation density exceeding 1016 m-2.

Unveiling the main factors triggering the coagulation at the SiC-blood interface.

Hemocompatibility is the most significant criterion for blood-contacting materials in successful in vivo applications. Prior to the clinical tests, in vitro analyses must be performed on the biomaterial surfaces in accordance with the ISO 10993-4 standards. Designing a bio-functional material requires engineering the surface structure and chemistry, which significantly influence the blood cell activity according to earlier studies. In this study, we elucidate the role of surface terminations and polymorphs of SiC single crystals in the initial stage of the contact coagulation. We present a detailed analysis of phase, roughness, surface potential, wettability, consequently, reveal their effect on cytotoxicity and hemocompatibility by employing live/dead stainings, live cell imaging, ELISA and Micro BCA protein assay. Our results showed that the surface potential and the wettability strongly depend on the crystallographic polymorph as well as the surface termination. We show, for the first time, the key role of SiC surface termination on platelet activation. This dependency is in good agreement with the results of our in vitro analysis and points out the prominence of cellular anisotropy. We anticipate that our experimental findings bridge the surface properties to the cellular activities, and therefore, pave the way for tailoring advanced hemocompatible surfaces.

Titanium matrix composites reinforced with biogenic filler.

Novel metal matrix composites (MMCs) have been fabricated with Ti6Al4V matrix and a biogenic ceramic filler in the form of diatomaceous earth (DE). Mixtures of DE and Ti6Al4V powders were consolidated by the spark plasma sintering (SPS) method. Microstructure of the consolidated samples has been investigated with microscopic techniques and XRD. Thermomechanical characteristics have been obtained using small-sample techniques. The results obtained indicate that the fabricated composites show outstanding mechanical and thermal properties due to synergic effects between the filler and the matrix (beyond the rule of mixtures).

Properties of Cold Sprayed Titanium and Titanium Alloy Coatings after Laser Surface Treatment.

Additive manufacturing (AM) has seen remarkable development in recent years due to relatively high efficiency of the process. Cold spraying (CS) is a particular method of AM, in which titanium and titanium alloy powders are used. CS is a very competitive technology enabling the deposition of coatings, repairing machine parts, and manufacturing new components. For specific applications, the surface of cold-sprayed materials may require further processing. This paper reports an attempt to employ laser surface treatment (LST) of cold-sprayed coatings on an aluminium alloy substrate. The influence of laser beam interaction time on the coatings' properties was analysed. The microstructure was investigated and observed employing scanning electron microscopy (SEM). To evaluate residual stress after CS and LST, the sin2ψ technique was used. Investigations were also performed on Vickers hardness, contact angle, and surface roughness. Significant changes in the surface morphology of the coatings and elevated residual stress levels dependent on the laser beam interaction time were observed. Increased Vickers hardness was recorded for titanium alloy Ti6Al4V. LST also led to increased surface hydrophilicity of the modified materials Ti and Ti6Al4V.

Biomimetic in situ precipitation of calcium phosphate containing silver nanoparticles on zirconia ceramic materials for surface functionalization in terms of antimicrobial and osteoconductive properties.

OBJECTIVE: Zirconia is commonly used for manufacturing of dental implants thanks to its excellent mechanical, biological and aesthetic properties. However, its bioinertness inhibits bonding with the surrounding hard tissue and other surface interactions. In our study, we present a method for multifunctionalization of zirconia surface to improve its osseointegration and to minimize the infection risks. METHODS: For this reason, we introduced antibacterial and bioactive properties to zirconia surfaces by calcium phosphate biomimetic coating. The samples were incubated in vials in horizontal and vertical position in concentrated simulated body fluid (SBF) containing 0.1, 0.5, and 3 g/L of silver nanoparticles (Ag-NPs) and then were tested for their structure, surface properties, cytocompatibility and antibacterial properties. RESULTS AND SIGNIFICANCE: The results demonstrated that our method is suitable to introduce Ag-NPs at different concentrations into the calcium phosphate layer, i.e. from 0.05-26.6 atom% as shown by EDX. According to the results of CFU-assay these coatings exhibited antibacterial properties against S. aureus and E. coli in correlation with the concentration of Ag-NP. The potential cytotoxicity of the coated samples was determined by AlamarBlue® assay and live/dead staining of MG63 osteoblast-like cells in direct contact and by testing the extracts from the materials. Only samples containing 0.05 atom% Ag-NPs, i.e. incubated in vertical position at SBF with 0.01 g/L Ag-NPs, were found cytocompatible in direct contact with MG63 cells. On the contrary in the indirect tests, the extracts from all the materials were found cytocompatible. This method could allow developing the completely new material group, exhibiting not only one but several biological properties, which can improve osseointegration and minimize infection risks.

Toward Innovative Hemocompatible Surfaces: Crystallographic Plane Impact on Platelet Activation.

The anticoagulation treatment of cardiovascular patients, which is mandatory after implantation of heart valves or stents, has significantly adverse effects on life quality. This treatment can be reduced or even circumvented by developing novel antithrombogenic surfaces of blood-contacting implants. Thus, we aim to discover materials exhibiting outstanding hemocompatibility compared to other available synthetic materials. We present promising surficial characteristics of single crystalline alumina in terms of platelet activation inhibition. In order to elucidate the relation between its crystallographic properties including the plane orientation and blood cell behavior, we examined endothelialization, cytocompatibility, and platelet activation at the blood-alumina interfaces in a controlled experimental setup. We observed that the cell response is highly sensitive to the plane orientation and differs significantly for (0001) and (11-20) planes of Al2O3. Our results reveal for the first time the dependence of platelet activation on crystallographic orientation, which is assumed to be a critical condition controlling the thrombogenicity. Additionally, we used an endothelial cell monolayer as an internal control since endothelial cells have an impact on vessel integrity and implant acceptance. We successfully demonstrate that Al2O3(11-20) exhibits enhanced hemocompatibility in contrast to Al2O3(0001) and is comparable to the physiological endothelial monolayer in vitro.