Physical, Mechanical, and Microstructure Characteristics of Ultra-High-Performance Concrete Containing Lightweight Aggregates.

This study explores and enhances the resistance of an ultra-high-performance concrete (UHPC) to explosive spalling under elevated temperatures. This study investigates the impact of lightweight aggregates (LWAs) on the mechanical and microstructural properties of the UHPC. Various UHPC specimens were created by replacing silica sand with LWAs in percentages ranging from 0% to 30%. The evaluation of these specimens involved assessing their compressive and flexural strengths, density, mass loss, shrinkage, porosity, and microstructural characteristics using scanning electron microscopy (SEM). This study provides valuable insights by analyzing the influence of lightweight aggregates on the strength, durability, and microstructure of UHPC. The results reveal that incorporating LWAs in the UHPC improved its flowability while decreasing its density, as the percentage of LWAs increased from 5% to 30%. Including 30% LWA resulted in a mass loss of 4.8% at 300 °C, which reduced the compressive and flexural strengths across all curing durations. However, the UHPC samples subjected to higher temperatures displayed higher strength than those exposed to ambient conditions. The microstructure analysis demonstrated that the UHPC specimens with 30% LWA exhibited increased density due to continuous hydration from the water in the lightweight aggregate. The pore size distribution graph indicated that incorporating more of the LWA increased porosity, although the returns diminished beyond a certain point. Overall, these findings offer valuable insights into the influence of lightweight aggregates on the physical and strength characteristics of UHPC. This research holds significant implications for developing high-performance, lightweight concrete materials.

Experimental Analysis of Channel Steel Member under Tension Load with Damage in the Unconnected Legs.

Damage occurring to steel element structures is highly possible due to tearing ruptures, corrosion, or the adoption of sudden loads. The damage has a great effect on their capacity to bear load and the corresponding elongation, as well as the distribution of the stresses in the cross-section of the element. Therefore, in the present research, experimental tests were carried out on 15 specimens of channel steel elements with different damage ratios in the unconnected legs and at different locations along the element's length. Through the test, the load and the corresponding elongation values were obtained for the control and damaged specimens. From the study of the different variables, it was demonstrated that the damage location does not significantly affect the load capacity, with a maximum difference of 1.9%. With the presence of the damage in only one leg at a ratio of less than or equal to 40%, the prediction of the value of the loss in the load is within the safe limit. However, if this ratio increases, there is a defect in calculating the loss in the load as it is greater than the effect of the damage. If there is any damage in the two legs of the channel together, the prediction of the loss of load is within the safe limit, where the loss is less than the effect of the damage ratio. We propose a model that can predict the capacitance of the axial load of steel channel elements through identifying the ratio of damage in the unconnected leg.

Investigation of Alkali-Activated Slag-Based Composite Incorporating Dehydrated Cement Powder and Red Mud.

Recycled construction cementitious materials (RCCM) and red mud (RM) could be considered a type of discarded material with potential cementitious properties. Generally, landfilling and stacking are utilized to dispose of this type of solid waste, which can be detrimental to the environment and sustainability of the construction sector. Accordingly, a productive process for making eco-efficient alkali-activated slag-based samples with the inclusion of RCCM and red mud is studied in this paper. Dehydrated cement powder (DCP) is attained through the high-temperature treatment of RCCM, and red mud can be obtained from the alumina industry. Subsequently, DCP and RM are utilized as a partial substitute for granulated blast furnace slag (GBFS) in alkali-activated mixtures. Two different batches were designed; the first batch had only DCP at a dosage of 15%, 30%, 45%, and 60% as a partial substitute for GBFS, and the second batch had both DCP and RM at 15%, 30%, 45%, and 60% as a partial substitute for GBFS. Different strength and durability characteristics were assessed. The findings show that when both dehydrated cement powder and red mud are utilized in high quantities, the strength and durability of the specimens were enhanced, with compressive strength improving by 42.2% at 28 days. Such improvement was obtained when 7.5% each of DCP and RM were added. The results revealed that DCP and RM have a negative effect on workability, whilst they had a positive impact on the drying shrinkage as well as the mechanical strength. X-ray diffraction and micro-structural analysis showed that when the amount of DCP and RM is increased, a smaller number of reactive products forms, and the microstructure was denser than in the case of the samples made with DCP alone. It was also confirmed that when DCP and RM are used at optimized dosages, they can be a potential sustainable binder substitute; thus, valorizing wastes and inhibiting their negative environmental footprint.

Repurposing carbonate-based waste for producing an innovative binder: optimization and characterization.

This study reports the full recycling of dolomite waste (DW) in the fabrication of a novel cementitious material through a facile and eco-efficient method. The proposed technique includes mixing different alkali-activators (i.e., NaOH and Na2SiO3) with DW powder, followed by curing at room temperature. Based on the alkali-activator type, sodium oxide concentration, and curing time, the formulated mixtures yield a wide range of compressive strengths. When DW powder is mixed with different contents of NaOH (2.5, 5, and 7.5 wt.% Na2O), the resulting hardened materials exhibited modest compressive strengths (less than 11 MPa) due to the formation of the gaylussite Na2CO3·CaCO3·5H2O phase. Concerning the other chemical activator (Na2SiO3), a significant improvement in the compressive strengths of the resulted hardened materials was detected. This was ascribed to the formation of calcium silicate hydrate, with a high binding capacity, through the exchange reaction between Na2SiO3 and CaCO3 inside DW. The sample activated with Na2SiO3 (silica modulus of 1.5) equivalent to Na2O of 7.5 wt.% offered the highest 90-day compressive strength (34 MPa). At silica modulus lower or higher than 1.5, a noticeable decrease in the performance of the hardened materials was observed, which could be attributed to the alter in binding phase composition. Overall, the present work presented a new approach in utilizing the available and low cost carbonate-based wastes as main precursors in the family of promising alkali-activated materials.

Effect of Polymers on Behavior of Ultra-High-Strength Concrete.

The development of ultra-high-performance concrete (UHPC) is still practically limited due to the scarcity of robust mixture designs and sustainable sources of local constituent materials. This study investigates the engineering characteristics of Styrene Butadiene Rubber (SBR) polymeric fiber-reinforced UHPC with partial substitution of cement at 0, 5 and 20 wt.% with latex polymer under steam and air curing techniques. The compressive and tensile strengths along with capillary water absorption and sulfate resistance were measured to evaluate the mechanical and durability properties. Scanning Electron Microscopy (SEM) was carried out to explore the microstructure development and hydration products in the designed mixtures under different curing regimes. The results indicated that the mixtures incorporating 20 wt.% SBR polymer achieved superior compressive strength at later ages. Additionally, the tensile strength of the polymeric UHPC without steel fibers and with 20% polymers was enhanced by 50%, which promotes the development of novel UHPC mixtures in which steel fibers could be partially replaced by polymer, while enhancing the tensile properties.

Assessment of seismic hazards in Yemen.

The seismic hazard analyses for Yemen have attracted the attention of researchers during the last two decades. However, the studies are limited and mainly use deterministic or approximate conventional probabilistic approaches. The conclusions drawn from these studies do not fit with current seismic design codes (International Building Code). This article presented the method and findings of a probabilistic seismic hazard assessment for Yemen in accordance with current seismic design building regulations. All the data sources, available nationally and internationally, were utilized in compiling earthquake database by covering the recent records and the seismic activity maps of the study region. The study area was regionalized to 11 seismotectonic area sources on the basis of the seismicity maps and available tectonic maps. On the analytical side, the earthquake recurrence analysis was evaluated for each source, and logic tree concept was used to model the seismic sources that may have significant effect on seismic hazard evaluation of Yemen as a combination of area and line sources. A probabilistic forecasting model was formulated, appropriate ground motion attenuation relationships were used, and seismic hazard contour maps were developed for the entire Yemen area. The maps present dense contours of peak ground accelerations and short and long period spectral accelerations for different return periods. The highest predicted seismic hazard is found in Dhamar City. This study provides basic and essential requirements that will be valuable in developing advanced seismic design criteria for Yemen.