Stable room-temperature continuous-wave lasing in quasi-2D perovskite films.

Organic-inorganic lead halide quasi-two-dimensional (2D) perovskites are promising gain media for lasing applications because of their low cost, tunable colour, excellent stability and solution processability1-3. Optically pumped continuous-wave (CW) lasing is highly desired for practical applications in high-density integrated optoelectronics devices and constitutes a key step towards electrically pumped lasers4-6. However, CW lasing has not yet been realized at room temperature because of the 'lasing death' phenomenon (the abrupt termination of lasing under CW optical pumping), the cause of which remains unknown. Here we study lead halide-based quasi-2D perovskite films with different organic cations and observe that long-lived triplet excitons considerably impede population inversion during amplified spontaneous emission and optically pumped pulsed and CW lasing. Our results indicate that singlet-triplet exciton annihilation is a possible intrinsic mechanism causing lasing death. By using a distributed-feedback cavity with a high quality factor and applying triplet management strategies, we achieve stable green quasi-2D perovskite lasers under CW optical pumping in air at room temperature. We expect that our findings will pave the way to the realization of future current-injection perovskite lasers.

High performance from extraordinarily thick organic light-emitting diodes.

Organic light-emitting diode (OLED) technology is promising for applications in next-generation displays and lighting. However, it is difficult-especially in large-area mass production-to cover a large substrate uniformly with organic layers, and variations in thickness cause the formation of shunting paths between electrodes1,2, thereby lowering device production yield. To overcome this issue, thicker organic transport layers are desirable because they can cover particles and residue on substrates, but increasing their thickness increases the driving voltage because of the intrinsically low charge-carrier mobilities of organics. Chemical doping of organic layers increases their electrical conductivity and enables fabrication of thicker OLEDs3,4, but additional absorption bands originating from charge transfer appear5, reducing electroluminescence efficiency because of light absorption. Thick OLEDs made with organic single crystals have been demonstrated6, but are not practical for mass production. Therefore, an alternative method of fabricating thicker OLEDs is needed. Here we show that extraordinarily thick OLEDs can be fabricated by using the organic-inorganic perovskite methylammonium lead chloride, CH3NH3PbCl3 (MAPbCl3), instead of organics as the transport layers. Because MAPbCl3 films have high carrier mobilities and are transparent to visible light, we were able to increase the total thickness of MAPbCl3 transport layers to 2,000 nanometres-more than ten times the thickness of standard OLEDs-without requiring high voltage or reducing either internal electroluminescence quantum efficiency or operational durability. These findings will contribute towards a higher production yield of high-quality OLEDs, which may be used for other organic devices, such as lasers, solar cells, memory devices and sensors.

"Core-Shell" Wave Function Modulation in Organic Narrowband Emitters.

Efficient red-green-blue primary luminescence with an extraordinarily narrow band and durability is crucial for advanced display applications. Recently, the emergence of multiple-resonance (MR) from short-range atomic interactions has been shown to induce extremely narrow spectral widths in pure organic emitters. However, achieving wide-range color tuning without compromising color purity remains a persistent challenge for MR emitters. Herein, the concept of electronic donor/acceptor "core-shell" modulation is proposed within a boron/nitrogen (B/N) MR skeleton, enabling the rational utilization of intramolecular charge transfer to facilitate wavelength shift. The dense B atoms localized at the center of the molecule effectively compress the electron density and stabilize the lowest unoccupied molecular orbital wave function. This electron-withdrawing core is embedded with peripheral electron-donating atoms. Consequently, doping a single B atom into a deep-blue MR framework led to a profound bathochromic shift from 447 to 624 nm (∼0.8 eV) while maintaining a narrow spectral width of 0.10 eV in this pure-red emitter. Notably, organic light-emitting diodes assisted by thermally activated delayed fluorescence molecules achieved superb electroluminescent stability, with an LT99 (99% of the initial luminance) exceeding 400 h at an initial luminance of 1000 cd m-2, approaching commercial-level performance without the assistance of phosphors.

Luminescence mechanism analysis of a TADF molecule showing peculiar thermal behavior.

In recent years, much attention has been paid to the development of thermally activated delayed fluorescence (TADF) materials with short delayed-fluorescence lifetimes to improve the device performances of OLEDs. In principle, by reducing the highest occupied molecular orbital (HOMO)-lowest unoccupied molecular orbital (LUMO) overlap, while the energy difference between S1-T1 (ΔEST) and activation energy (Ea) can be reduced, and the reverse intersystem crossing rate constant (kRISC) can be accelerated, a decrease in the radiative rate constant happens, necessitating an advanced molecular design. Furthermore, a molecule based on heptazine as a parent skeleton has recently been found to have a peculiar temperature dependence of luminescence decay, suggesting a negative gap (NG) material. In this report, we show that 9-[1,4]benzoxaborino[2,3,4-kl]phenoxaborine-7-yl-1,3,6,8-tetramethyl-9H-carbazole (TMCz-BO), a donor-acceptor linked TADF molecule with a very short delay lifetime of 750 ns, exhibits a peculiar thermal behavior similar to that of NG materials based on the temperature dependence of its luminescence decay in solution.

A Rigid Multiple Resonance Thermally Activated Delayed Fluorescence Core Toward Stable Electroluminescence and Lasing.

The investigation of organic light-emitting diodes (OLEDs) and organic laser devices with thermally activated delayed fluorescence (TADF) molecules is emerging due to the potential of harnessing triplets. In this work, a boron/nitrogen multiple-resonance TADF polycyclic framework fusing carbazole units (CzBNPh) was proposed. CzBNPh exhibited a narrowband emission (<30 nm), a unity photoluminescence quantum yield, and a fast radiative rate. Consequently, CzBNPh demonstrated a low distributed feedback (DFB) lasing threshold of 0.68 µJ cm-2 . Furthermore, the stimulated emission zone of CzBNPh was effectively separated from its singlet and triplet absorption, thereby minimizing the singlet-triplet annihilation under long-pulsed excitation ranging from 20 µs to 2.5 ms. Significantly, the enhanced rigid molecular conformation, thermal stability, and photo-stability resulted in improved lasing and electroluminescence stability compared to that of 5,9-diphenyl-5,9-diaza-13b-boranaphtho[3,2,1-de]anthracene (DABNA)-core. These findings indicate the potential of CzBN-core as a promising framework for achieving long-pulsed wave and electrically-pumped lasing in the future.

Sequential Multiple Borylation Toward an Ultrapure Green Thermally Activated Delayed Fluorescence Material.

Multiple-resonance thermally activated delayed fluorescence (MR-TADF) emitters have emerged as an important component of organic light-emitting diodes (OLEDs) because of their narrowband emission and high exciton utilization efficiency. However, the chemical space of MR-TADF emitters remains mostly unexplored because of the lack of suitable synthetic protocols. Herein, we demonstrate a sequential multiple borylation reaction that provides new synthetically accessible chemical space. ω-DABNA, the proof-of-concept material, exhibited narrowband green TADF with a full width at half-maximum of 22 nm and a small singlet-triplet energy gap of 13 meV. The OLED employing it as an emitter exhibited electroluminescence at 512 nm, with Commission International de l'Éclairage coordinates of (0.13, 0.73) and a high external quantum efficiency (EQE) of 31.1%. Moreover, the device showed minimum efficiency roll-off, with an EQE of 29.4% at 1000 cd m-2.

Spontaneous formation of metastable orientation with well-organized permanent dipole moment in organic glassy films.

The performance of organic optoelectronic and energy-harvesting devices is largely determined by the molecular orientation and resultant permanent dipole moment, yet this property is difficult to control during film preparation. Here, we demonstrate the active control of dipole direction-that is, vector direction and magnitude-in organic glassy films by physical vapour deposition. An organic glassy film with metastable permanent dipole moment orientation can be obtained by utilizing the small surface free energy of a trifluoromethyl unit and intramolecular permanent dipole moment induced by functional groups. The proposed molecular design rule could pave a way toward the formation of spontaneously polarized organic glassy films, leading to improvement in the performance of organic molecular devices.

Organic long-persistent luminescence stimulated by visible light in p-type systems based on organic photoredox catalyst dopants.

Organic long-persistent-luminescent (OLPL) materials demonstrating hour-long photoluminescence have practical advantages in applications owing to their flexible design and easy processability. However, the energy absorbed in these materials is typically stored in an intermediate charge-separated state that is unstable when exposed to oxygen, thus preventing persistent luminescence in air unless oxygen penetration is suppressed through crystallization. Moreover, OLPL materials usually require ultraviolet excitation. Here we overcome such limitations and demonstrate amorphous OLPL systems that can be excited by radiation up to 600 nm and exhibit persistent luminescence in air. By adding cationic photoredox catalysts as electron-accepting dopants in a neutral electron-donor host, stable charge-separated states are generated by hole diffusion in these blends. Furthermore, the addition of hole-trapping molecules extends the photoluminescence lifetime. By using a p-type host less reactive to oxygen and tuning the donor-acceptor energy gap, our amorphous blends exhibit persistent luminescence stimulated by visible light even in air, expanding the applicability of OLPL materials.

Organic long persistent luminescence.

Long persistent luminescence (LPL) materials-widely commercialized as 'glow-in-the-dark' paints-store excitation energy in excited states that slowly release this energy as light. At present, most LPL materials are based on an inorganic system of strontium aluminium oxide (SrAl2O4) doped with europium and dysprosium, and exhibit emission for more than ten hours. However, this system requires rare elements and temperatures higher than 1,000 degrees Celsius during fabrication, and light scattering by SrAl2O4 powders limits the transparency of LPL paints. Here we show that an organic LPL (OLPL) system of two simple organic molecules that is free from rare elements and easy to fabricate can generate emission that lasts for more than one hour at room temperature. Previous organic systems, which were based on two-photon ionization, required high excitation intensities and low temperatures. By contrast, our OLPL system-which is based on emission from excited complexes (exciplexes) upon the recombination of long-lived charge-separated states-can be excited by a standard white LED light source and generate long emission even at temperatures above 100 degrees Celsius. This OLPL system is transparent, soluble, and potentially flexible and colour-tunable, opening new applications for LPL in large-area and flexible paints, biomarkers, fabrics, and windows. Moreover, the study of long-lived charge separation in this system should advance understanding of a wide variety of organic semiconductor devices.

Anti-Stokes Luminescence in Multi-Resonance-Type Thermally-Activated Delayed Fluorescence Molecules.

Photon-upconversion in organic molecular systems is one of the promising technologies for future energy harvesting systems because these systems can generate excitons that possess higher energy than excitation energy. The photon-upconversion caused by absorbing ambient heat as additional energy is particularly interesting because it could ideally provide a light-driving cooling system. However, only a few organic molecular systems have been reported. Here, we report the anti-Stokes photoluminescence (ASPL) derived from hot-band absorption in a series of multi-resonance-type thermally-activated delayed fluorescence (MR-TADF) molecules. The MR-TADF molecules exhibited an anti-Stokes shift of approximately 0.1 eV with a high PL quantum yield in the solution state. The anti-Stokes shift corresponded well to the 1-0 vibration transition from the ground state to the excited singlet state, and we further evaluated a correlation between the activation energy for the ASPL intensity and the TADF process. Our demonstration underlines that MR-TADF molecules have become a novel class of ASPL materials for various future applications, such as light-driving cooling systems.

Spiroconjugated Tetraaminospirenes as Donors in Color-Tunable Charge-Transfer Emitters with Donor-Acceptor Structure.

Charge-transfer emitters are attractive due to their color tunability and potentially high photoluminescence quantum yields (PLQYs). We herein present tetraaminospirenes as donor moieties, which, in combination with a variety of acceptors, furnished 12 charge-transfer emitters with a range of emission colors and PLQYs of up to 99 %. The spatial separation of their frontier molecular orbitals was obtained through careful structural design, and two DA structures were confirmed by X-ray crystallography. A range of photophysical measurements supported by DFT calculations shed light on the optoelectronic properties of this new family of spiro-NN-donor-acceptor dyes.

Trifluoromethylated thermally activated delayed fluorescence molecule as a versatile photocatalyst for electron-transfer- and energy-transfer-driven reactions.

In this study, we propose that the trifluoromethylated thermally activated delayed fluorescent molecule 4[Cz(CF3)2]IPN is a versatile organic photocatalyst that can be used for electron-transfer-driven reactions requiring a photocatalyst with high oxidizing power and energy-transfer-driven reactions that require an Ir photocatalyst. 4[Cz(CF3)2]IPN was used in radical reactions via electron transfer and dearomative cycloaddition reactions via energy transfer.

Low Light Amplification Threshold and Reduced Efficiency Roll-Off in Thick Emissive Layer OLEDs from a Diketopyrrolopyrrole Derivative.

External quantum efficiency (EQE) roll-off under high current injection has been one of the major limiting factors toward the development of organic semiconductor laser diodes (OSLDs). While significant progress in this regard has been made on organic semiconductors (OSCs) emitting in the blue-green region of the visible spectrum, OSCs with longer wavelength emission (>600 nm) have fallen behind in both material development and the advancement in device architectures suitable for the realization of OSLDs. Therefore, to make simultaneous incremental advancements, a host-guest system comprising of a high performing poly(9,9-dioctylfluorene-alt-benzothiadiazole) (F8BT) polymer and an efficient small molecule laser dye, dithiophenyl diketopyrrolopyrrole (DT-DPP), is used. This combination provides an extremely low amplified spontaneous emission threshold of 4.2 µJ cm-2 at an emission wavelength of 620 nm. The solution-processed organic light-emitting diodes (OLEDs) fabricated using this system exhibit a high external quantum efficiency (EQE) of 2.6% with low efficiency roll-off and high current injection up to 90 A cm-2 to yield ultrahigh luminance of over 1.5 million cd m-2 .

Cibalackrot Dendrimers for Hyperfluorescent Organic Light-Emitting Diodes.

Hyperfluorescent organic light-emitting diodes (HF-OLEDs) enable a cascading Förster resonance energy transfer (FRET) from a suitable thermally activated delayed fluorescent (TADF) assistant host to a fluorescent end-emitter to give efficient OLEDs with relatively narrowed electroluminescence compared to TADF-OLEDs. Efficient HF-OLEDs require optimal FRET with minimum triplet diffusion via Dexter-type energy transfer (DET) from the TADF assistant host to the fluorescent end-emitter. To hinder DET, steric protection of the end-emitters has been proposed to disrupt triplet energy transfer. In this work, the first HF-OLEDs based on structurally well-defined macromolecules, dendrimers is reported. The dendrimers contain new highly twisted dendrons attached to a Cibalackrot core, resulting in high solubility in organic solvents. HF-OLEDs based on dendrimer blend films are fabricated to show external quantum efficiencies of >10% at 100 cd m-2 . Importantly, dendronization with the bulky dendrons is found to have no negative impact to the FRET efficiency, indicating the excellent potential of the dendritic macromolecular motifs for HF-OLEDs. To fully prevent the undesired triplet diffusion, Cibalackrot dendrimers HF-OLEDs are expected to be further improved by adding additional dendrons to the Cibalackrot core and/or increasing dendrimer generations.

Highly Effective Thermally Activated Delayed Fluorescence Emitters Based on Symmetry and Asymmetry Nicotinonitrile Derivatives.

In this study, we developed two thermally activated delayed fluorescence (TADF) emitters, ICzCN and ICzCYP, to apply to organic light-emitting diodes (OLEDs). These emitters involve indolocarbazole (ICz) donor units and nicotinonitrile acceptor units with a twisted donor-acceptor-donor (D-A-D) structure for small singlet (S1) and triplet (T1) state energy gap (ΔEST) to enable efficient exciton transfer from the T1 to the S1 state. Depending on the position of the cyano-substituent, ICzCN has a symmetric structure by introducing donor units at the 3,5-position of isonicotinonitrile, and ICzCYP has an asymmetric structure by introducing donor units at the 2,6-position of nicotinonitrile. These emitters have different properties, such as the maximum luminance (Lmax) value. The Lmax of ICzCN reached over 10000 cd m-2. The external quantum efficiency (ηext) was 14.8% for ICzCN and 14.9% for ICzCYP, and both achieved a low turn-on voltage (Von) of less than 3.4 eV.

Synthesis, Aromaticity, and Application of peri-Pentacenopentacene: Localized Representation of Benzenoid Aromatic Compounds.

We report the synthesis and optoelectronic properties of TIPS-peri-pentacenopentacene (TIPS-PPP), a vertical extension of TIPS-pentacene (TIPS-PEN) and a low-band-gap material with remarkable stability. We found the synthetic conditions to avoid the competition between 1,2- and 1,4-addition of lithium acetylide on the large aromatic dione. The high stability of TIPS-PPP is due to the peri-fusion which increases the aromaticity by generating two localized aromatic sextets that are flanked with 2 diene fragments, similar to two fused-anthracenes. Like TIPS-PEN, TIPS-PPP shows the archetypal 2D brickwall motif in crystals with a larger transfer integral and smaller reorganization energy. The high mobility of up to 1 cm2 V-1 s-1 was obtained in an organic field-effect transistor fabricated by a wet process. Also, TIPS-PPP was used as a near-infrared (NIR) emitter for NIR organic-light-emitting-diode devices resulting in a high external quantum efficiency at 800 nm.

Steric Modulation of Spiro Structure for Highly Efficient Multiple Resonance Emitters.

A multiple resonance thermally activated delayed fluorescence (MR-TADF) molecule with a fused, planar architecture tends to aggregate at high doping ratios, resulting in broad full width at half maximum (FWHM), redshifting electroluminescence peaks, and low device efficiency. Herein, we propose a mono-substituted design strategy by introducing spiro-9,9'-bifluorene (SBF) units with different substituted sites into the MR-TADF system for the first time. As a classic steric group, SBF can hinder interchromophore interactions, leading to high device efficiency (32.2-35.9 %) and narrow-band emission (≈27 nm). Particularly, the shield-like molecule, SF1BN, seldom exhibits a broadened FWHM as the doping ratio rises, which differs from the C3-substituted isomer and unhindered parent emitter. These results manifest an effective method for constructing highly efficient MR-TADF emitters through a spiro strategy and elucidate the feasibility for steric modulation of the spiro structure in π-framework.

An Electron-Accepting aza-BODIPY-Based Donor-Acceptor-Donor Architecture for Bright NIR Emission.

A bright near-infrared (NIR) fluorescent molecule was developed based on the donor-acceptor-donor (D-A-D) approach using an aza-BODIPY analog called pyrrolopyrrole aza-BODIPY (PPAB) as an electron-accepting chromophore. Directly introducing electron-donating triphenylamine (TPA) to develop a D-A-D structure caused redshifts of absorption and emission of PPAB into the NIR region with an enhanced fluorescence brightness of up to 5.2×104  m-1 cm-1 , whereas inserting a phenylene linker between the TPA donor and the PPAB acceptor induced solvatochromic behavior in emission. Transient absorption spectra and theoretical calculations revealed the presence of a highly emissive hybridized locally excited and charge-transfer state in the former case and the contribution of the dark charge-separated state to the excited state in the latter case. The bright D-A-D PPAB as a novel emitter resulted in a NIR electroluminescence with a high external quantum efficiency of 3.7 % and a low amplified spontaneous emission threshold of ca. 80 µJ cm-2 , indicating the high potential for NIR optoelectronic applications.

Heptacene: Synthesis and Its Hole-Transfer Property in Stable Thin Films.

Heptacene (1) has been produced via a monoketone precursor, 2, which was prepared from 1,2,4,5-tetrabromobenzene in nine steps in a total yield of 10 %. Compound 2 was converted to 1 quantitatively by heating at 202 °C. Heptacene exhibited high thermal stability in the solid state without any observable change over two months. To investigate the potential value of 1 as a material for p-type organic field-effect transistors (OFETs), top-contact OFET devices were fabricated by vacuum deposition of 1 onto a hexamethyldisilazane (HMDS)/SiO2 /Si substrate. The best hole mobility performance was 2.2 cm2  V-1 s-1 . This is the first report of stable heptacene being used in an effective device and examined for its charge carrier properties.

Exact Solution of Kinetic Analysis for Thermally Activated Delayed Fluorescence Materials.

The photophysical analysis of thermally activated delayed fluorescence (TADF) materials has become instrumental for providing insights into their stability and performance, which is not only relevant for organic light-emitting diodes but also for other applications such as sensing, imaging, and photocatalysis. Thus, a deeper understanding of the photophysics underpinning the TADF mechanism is required to push materials design further. Previously reported analyses in the literature of the kinetics of the various processes occurring in a TADF material rely on several a priori assumptions to estimate the rate constants for forward and reverse intersystem crossing. In this report, we demonstrate a method to determine these rate constants using a three-state model together with a steady-state approximation and, importantly, no additional assumptions. Further, we derive the exact rate equations, greatly facilitating a comparison of the TADF properties of structurally diverse emitters and providing a comprehensive understanding of the photophysics of these systems.