RESUMEN
With the development of miniaturization and integration of electrical and electronic equipment, the heat accumulation problems caused by the long-term operation of devices have become more and more serious. High thermal-conductivity and high-performance plastic composites have attracted significant interest from both academia and industry. Numerous studies have been recently conducted to enhance the thermal conductivity (TC) of nanofiller-filled polymeric composites. However, the homogeneous dispersion and directional arrangement of nanofillers in the resin matrix are the key factors limiting their effectiveness in enhancing thermal conductivity. Based on the feasibility considerations of mass production and industrial application, this paper reports on a novel preparation method of Poly(decamethylene terephthalamide)/graphite nanoparticle (GNP) nanocomposites with high thermal conductivity. Without borrowing solvents or other reagents, this method can effectively strip the inexpensive scaled graphite into nanoscale for its uniform dispersion and orientation arrangement by relying only on mechanical external forces. The whole technology is simple, green, and easy to industrialize. The fillers were well-dispersed and aligned in the PA10T, which played a role in significantly enhancing the thermal conductivity of the PA10T. In addition, we found that the thermal conductivity of the composites reached 1.20 W/(m·K) at 10 wt% filler content, which was 330% higher than that of the pure matrix. The mechanical properties of the composites were also significantly improved. This work provides guidance for the easy fabrication of thermally conductive composites with aligned structures.
RESUMEN
As a representative sulfur-containing volatile organic compounds (S-VOCs), CH3SH has attracted widespread attention due to its adverse environmental and health risks. The performance of Mn-based catalysts and the effect of their crystal structure on the CH3SH catalytic reaction have yet to be systematically investigated. In this paper, two different crystalline phases of tunneled MnO2 (α-MnO2 and ß-MnO2) with the similar nanorod morphology were used to remove CH3SH, and their physicochemical properties were comprehensively studied using high-resolution transmission electron microscope (HRTEM) and electron paramagnetic resonance (EPR), H2-TPR, O2-TPD, Raman, and X-ray photoelectron spectroscopy (XPS) analysis. For the first time, we report that the specific reaction rate for α-MnO2 (0.029 mol g-1 h-1) was approximately 4.1 times higher than that of ß-MnO2 (0.007 mol g-1 h-1). The as-synthesized α-MnO2 exhibited higher CH3SH catalytic activity towards CH3SH than that of ß-MnO2, which can be ascribed to the additional oxygen vacancies, stronger surface oxygen migration ability, and better redox properties from α-MnO2. The oxygen vacancies on the catalyst surface provided the main active sites for the chemisorption of CH3SH, and the subsequent electron transfer led to the decomposition of CH3SH. The lattice oxygen on catalysts could be released during the reaction and thus participated in the further oxidation of sulfur-containing species. CH3SSCH3, S0, SO32-, and SO42- were identified as the main products of CH3SH conversion. This work offers a new understanding of the interface interaction mechanism between Mn-based catalysts and S-VOCs.
RESUMEN
The cooperative transition of sulfur-containing pollutants of H2S/CO/H2 to the high-value chemical methyl mercaptan (CH3SH) is catalyzed by Mo-based catalysts and has good application prospects. Herein, a series of Al2O3-supported molybdenum carbide catalysts with K doping (denoted herein as K-Mo2C/Al2O3) are fabricated by the impregnation method, with the carbonization process occurring under different atmospheres and different temperatures between 400 and 600 °C. The CH4-K-Mo2C/Al2O3 catalyst carbonized by CH4/H2 at 500 °C displays unprecedented performance in the synthesis of CH3SH from CO/H2S/H2, with 66.1% selectivity and a 0.2990 g·gcat-1·h-1 formation rate of CH3SH at 325 °C. H2 temperature-programmed reduction, temperature-programmed desorption, X-ray diffraction and Raman and BET analyses reveal that the CH4-K-Mo2C/Al2O3 catalyst contains more Mo coordinatively unsaturated surface sites that are responsible for promoting the adsorption of reactants and the desorption of intermediate products, thereby improving the selectivity towards and production of CH3SH. This study systematically investigates the effects of catalyst carbonization and passivation conditions on catalyst activity, conclusively demonstrating that Mo2C-based catalyst systems can be highly selective for producing CH3SH from CO/H2S/H2.