The effect of source backing materials and excitation pulse durations on laser-generated ultrasound waveforms.

In this article, it is shown experimentally that a planar laser-generated ultrasound source with a hard reflective backing will generate higher acoustic pressures than a comparable source with an acoustically matched backing when the stress confinement condition is not met. Furthermore, while the source with an acoustically matched backing will have a broader bandwidth when the laser pulse is short enough to ensure stress confinement, the bandwidths of both source types will converge as the laser pulse duration increases beyond stress confinement. The explanation of the results is supported by numerical simulations.

Controllable duration and repetition-rate picosecond pulses from a high-average-power OP-GaAs OPO.

We report an orientation-patterned gallium arsenide (OP-GaAs) optical parametric oscillator (OPO) offering a high degree of temporal flexibility with controllable pulse repetition rates from 100 MHz to 1 GHz and pulse durations from ∼95 ps to ∼1.1 ns. The maximum average power of 9.2-W signal (3.3 µm) and 4.5-W idler (4.9 µm) was obtained at a repetition rate of 100 MHz and a pulse duration of ∼95 ps, with a pump power of 34.3 W and at a slope efficiency of 45.4%. The corresponding total average output power of 13.7 W is the highest power achieved to date from an OP-GaAs OPO, to the best of our knowledge.

High-average-power picosecond mid-infrared OP-GaAs OPO.

We report a high-average-power mid-infrared picosecond (ps) optical parametric oscillator (OPO) based on orientation-patterned gallium arsenide (OP-GaAs), with wide wavelength tunability. The OP-GaAs OPO is synchronously pumped by a thulium-doped-fiber (TDF) master oscillator power amplifier (MOPA), seeded by a gain-switched laser diode. At a pump power of 35.3 W and a repetition rate of 100 MHz, a maximum OPO total average output power of 9.7 W (signal 5.7 W (0.60 kW peak power), idler 4.0 W (0.42 kW peak power)) is obtained at signal and idler wavelengths of 3093 nm and 5598 nm, and a thermally induced power roll-off is observed. To mitigate the thermal effects, an optical chopper is placed before the OPO to provide burst mode operation and a reduced thermal load. We achieved a linear growth in OPO output power over the full range of available pump powers in this instance confirming thermal effects as the origin of the roll-off observed under continuous pumping. We estimate the maximum peak powers of the signal and idler are estimated to be over 0.79 kW and 0.58 kW, respectively in this instance. A wide mid-infrared wavelength tuning range of 2895-3342 nm (signal) and 4935-6389 nm (idler) is demonstrated.

Ultra-short wavelength operation of thulium-doped fiber amplifiers and lasers.

We fabricate and characterize a germanium/thulium (Ge/Tm) co-doped silica fiber in order to enhance the gain at the short wavelength edge of the thulium emission band (i.e. 1620-1660 nm). The Ge/Tm doped fiber shows an intrinsic blue-shifted absorption/emission cross-section compared to aluminum/thulium (Al/Tm) co-doped fiber, which greatly improves the short wavelength amplification and has enabled us to further extend the shortest wavelength of emission towards 1600 nm. Using this glass fiber composition, we have demonstrated both a silica-based thulium doped fiber amplifier (TDFA) in the 1628-1655 nm waveband and a tunable thulium-doped fiber laser (TDFL) capable of accessing the telecom U-band wavelength region. These results represent by far the shortest amplifier/laser wavelengths reported to-date from TDFAs/TDFLs.

Compact, high repetition rate, 4.2 MW peak power, 1925 nm, thulium-doped fiber chirped-pulse amplification system with dissipative soliton seed laser.

We report the demonstration of a high average- and peak-power, 1925 nm, thulium-fiber based chirped pulse amplification (CPA) system. A compact, dissipative soliton thulium-fiber, mode-locked seed produced pre-chirped pulses with 25 ps duration, 45 mW output power and repetition rate of 15.7 MHz. After stretching to 105 ps in 83 m of normal dispersion fiber, the pulses were amplified in a core-pumped pre-amplifier and a cladding pumped power amplifier to average output powers of 28 W and 30 W with forward and backward pumping, respectively, with the output power limited only by the available pump power. After a pair of fused silica transmission gratings with an efficiency of 71%, the amplified pulses were re-compressed to 297 fs yielding pulses with a peak power of 4.2 MW (backward pumped) and a pulse energy of 1.27 µJ.

295-kW peak power picosecond pulses from a thulium-doped-fiber MOPA and the generation of watt-level >2.5-octave supercontinuum extending up to 5 µm.

We report a gain-switched diode-seeded thulium doped fiber master oscillator power amplifier (MOPA) producing up to 295-kW picosecond pulses (35 ps) at a repetition rate of 1 MHz with a good beam quality (M2 ~1.3). A narrow-band, grating-based filter was incorporated within the amplifier chain to restrict the accumulation of nonlinear spectral broadening and counter-pumping of a short length of large-mode-area (LMA) fiber was used in the final stage amplifier to further reduce nonlinear effects. Finally, we generated watt-level >2.5-octave supercontinuum spanning from 750 nm to 5000 nm by using the MOPA output to pump an indium fluoride fiber.

5.6 kW peak power, nanosecond pulses at 274 nm from a frequency quadrupled Yb-doped fiber MOPA.

A 2 W deep-ultraviolet (DUV) source at 274 nm with 5.6 kW peak power is demonstrated by frequency quadrupling a diode-seeded, polarization-maintaining (PM), Yb-doped fiber master oscillator power amplifier (MOPA) system delivering 1.8 ns pulses at a repetition rate of 200 kHz. The second harmonic generation (SHG) and the fourth harmonic generation (FHG) are achieved by using Lithium Triborate (LBO) crystal and ß-BaB2O4 (BBO) crystal in sequence, with an IR-to-green and green-to-UV conversion efficiency of up to 65% and 26%, respectively. This is the first kW peak power pulsed UV system reported at 274 nm which has great potential for machining insulators, 2D materials, isotopic separation of Calcium-48, and fluorescence analysis of biological molecules.

Nonlinear dynamic of picosecond pulse propagation in atmospheric air-filled hollow core fibers.

Atmospheric air-filled hollow core (HC) fibers, representing the simplest yet reliable form of gas-filled hollow core fiber, show remarkable nonlinear properties and have several interesting applications such as pulse compression, frequency conversion and supercontinuum generation. Although the propagation of sub-picosecond and few hundred picosecond pulses are well-studied in air-filled fibers, the nonlinear response of air to pulses with a duration of a few picoseconds has interesting features that have not yet been explored fully. Here, we experimentally and theoretically study the nonlinear propagation of ~6 ps pulses in three different types of atmospheric air-filled HC fiber. With this pulse length, we were able to explore different nonlinear characteristics of air at different power levels. Using in-house-fabricated, state-of-the-art HC photonic bandgap, HC tubular and HC Kagomé fibers, we were able to associate the origin of the initial pulse broadening process in these fibers to rotational Raman scattering (RRS) at low power levels. Due to the broadband and low loss transmission window of the HC Kagomé fiber we used, we observed the transition from initial pulse broadening (by RRS) at lower powers, through long-range frequency conversion (2330 cm-1) with the help of vibrational Raman scattering, to broadband (~700 nm) supercontinuum generation at high power levels. To model such a wide range of nonlinear processes in a unified approach, we have implemented a semi-quantum model for air into the generalized nonlinear Schrodinger equation, which surpasses the limits of the common single damping oscillator model in this pulse length regime. The model has been validated by comparison with experimental results and provides a powerful tool for the design, modeling and optimization of nonlinear processes in air-filled HC fibers.

106 W, picosecond Yb-doped fiber MOPA system with a radially polarized output beam.

We report the generation of high average output power, high peak power, and high pulse energy radially polarized picosecond pulses from a compact gain-switched laser-diode-seeded Yb-doped fiber master oscillator power amplifier (MOPA) system. A q-plate was employed as a mode converter prior to the final power amplifier to efficiently convert the linearly polarized Gaussian-shaped beam into a donut-shaped radially polarized beam. The desired vector beam was efficiently amplified yielding ∼110 ps pulses with a maximum output pulse energy of ∼30.7 µJ and a peak power of ∼280 kW at a repetition rate of 1.367 MHz. The average power was scaled up to 106 W by increasing the repetition rate to 5.468 MHz.

All-optical mode-group multiplexed transmission over a graded-index ring-core fiber with single radial mode.

We present a design of graded-index ring-core fiber (GI-RCF) supporting 3 linearly polarized (LP) mode-groups (i.e. LP01, LP11 and LP21) with a single radial index of one for mode-division multiplexed (MDM) transmission. Reconfigurable spatial light modulator (SLM) based spatial (mode) (de)multiplexers are used to systematically characterize spatial/temporal modal properties of the GI-RCF. We also demonstrate all-optical mode-group multiplexed transmissions over a 360m fabricated GI-RCF without using multiple-input multiple-output digital signal processing (MIMO DSP).

Broadband silica-based thulium doped fiber amplifier employing multi-wavelength pumping.

A multi-wavelength pumped thulium doped fiber amplifier is investigated to extend the spectral gain coverage of the amplifier in the 1.7-1.9µm wavelength range. Through the use of a combination of 791 nm, 1240 nm, and 1560 nm laser diode pumping, the amplifier gain can be improved significantly and overall gain bandwidth enhancement of ~47% as compared to single-wavelength pumping achieved. A nominal gain of 15 dB is achieved over a bandwidth of more than 250 nm spanning from 1700 to 1950 nm with a maximum gain of 29 dB and a noise figure of less than 5 dB.

High gain holmium-doped fibre amplifiers.

We investigate the operation of holmium-doped fibre amplifiers (HDFAs) in the 2.1 µm spectral region. For the first time we demonstrate a diode-pumped HDFA. This amplifier provides a peak gain of 25 dB at 2040 nm with a 15 dB gain window spanning the wavelength range 2030 - 2100 nm with an external noise figure (NF) of 4-6 dB. We also compare the operation of HDFAs when pumped at 1950 nm and 2008 nm. The 1950 nm pumped HDFA provides 41 dB peak gain at 2060 nm with 15 dB of gain spanning the wavelength range 2050 - 2120 nm and an external NF of 7-10 dB. By pumping at the longer wavelength of 2008 nm the gain bandwidth of the amplifier is shifted to longer wavelengths and using this architecture a HDFA was demonstrated with a peak gain of 39 dB at 2090 nm and 15 dB of gain spanning the wavelength range 2050 - 2150 nm. The external NF over this wavelength range was 8-14 dB.

Generation of stretched pulses and dissipative solitons at 2 µm from an all-fiber mode-locked laser using carbon nanotube saturable absorbers.

We demonstrate for the first time, to the best of our knowledge, a thulium-doped, all-fiber, mode-locked laser using a carbon nanotube saturable absorber, operating in the dissipative-soliton regime and the stretched-pulse-soliton regime. The net dispersion of the laser cavity is adjusted by inserting different lengths of normal dispersion fiber, resulting in different mode-locking regimes. These results could serve as a foundation for the optimization of mode-locked fiber-laser cavity design at the 2 µm wavelength region.

High-energy, near- and mid-IR picosecond pulses generated by a fiber-MOPA-pumped optical parametric generator and amplifier.

We report a high-energy picosecond optical parametric generator/amplifier (OPG/A) based on a MgO:PPLN crystal pumped by a fiber master-oscillator-power-amplifier (MOPA) employing direct amplification. An OPG tuning range of 1450-3615 nm is demonstrated with pulse energies as high as 2.6 µJ (signal) and 1.2 µJ (idler). When seeded with a ~100 MHz linewidth diode laser, damage-limited pulse energies of 3.1 µJ (signal) and 1.3 µJ (idler) have been achieved and the signal pulse time-bandwidth product is improved to ~2 times transform-limited. When seeded with a 0.3 nm-bandwidth filtered amplified spontaneous emission source, crystal damage is avoided and maximum pulse energies of 3.8 µJ (signal) and 1.7 µJ (idler) are obtained at an overall conversion efficiency of 45%.

Amplification of 12 OAM Modes in an air-core erbium doped fiber.

We theoretically propose an air-core erbium doped fiber amplifier capable of providing relatively uniform gain for 12 orbital angular momentum (OAM) modes (|L| = 5, 6 and 7, where |L| is the OAM mode order) over the C-band. Amplifier performance under core pumping conditions for a uniformly doped core for each of the supported pump modes (110 in total) was separately assessed. The differential modal gain (DMG) was found to vary significantly depending on the pump mode used, and the minimum DMG was found to be 0.25 dB at 1550 nm provided by the OAM (8,1) pump mode. A tailored confined doping profile can help to reduce the pump mode dependency for core pumped operation and help to increase the number of pump modes that can support a DMG below 1 dB. For the more practical case of cladding-pumped operation, where the pump mode dependency is almost removed, a DMG of 0.25 dB and a small signal gain of >20 dB can be achieved for the 12 OAM modes across the full C-band.

Detailed study of four-wave mixing in Raman DFB fiber lasers.

We both experimentally and numerically studied the ultra-compact wavelength conversion by using the four-wave mixing (FWM) process in Raman distributed-feedback (R-DFB) fiber lasers. The R-DFB fiber laser is formed in a 30 cm-long commercially available Ge/Si standard optical fiber. The internal generated R-DFB signal acts as the pump wave for the FWM process and is in the normal dispersion range of the fiber. Utilizing a tunable laser source as a probe wave, FWM frequency conversion up to ~40 THz has been demonstrated with conversion efficiency > -40 dB. The principle of such a wide bandwidth and high conversion efficiency in such a short R-DFB cavity has been theoretically analyzed. The simulation results match well with the experimental data.

Minimizing differential modal gain in cladding-pumped EDFAs supporting four and six mode groups.

We employ a Genetic Algorithm for the purpose of minimization of the maximum differential modal gain (DMG) over all the supported signal modes (at the same wavelength) of cladding-pumped four-mode and six-mode-group EDFAs. The optimal EDFA designs found through the algorithm provide less than 1 dB DMG across the C-band (1530-1565 nm) whilst achieving more than 20 dB gain per mode. We then analyze the sensitivity of the DMG to small variations from the optimal value of the erbium doping concentration and the structural parameters, and estimate the fabrication tolerance for reliable amplifier performance.

Compact, high-pulse-energy, high-power, picosecond master oscillator power amplifier.

We report a compact, stable, gain-switched-diode-seeded master oscillator power amplifier (MOPA), employing direct amplification via conventional Yb(3+)-doped fibers, to generate picosecond pulses with energy of 17.7 µJ and 97-W average output power (excluding amplified spontaneous emission) at 5.47-MHz repetition frequency in a diffraction-limited and single-polarization beam. A maximum peak power of 197 kW is demonstrated. Such a high-energy, high-power, MHz, picosecond MOPA is of great interest for high-throughput material processing. With 13.8-µJ pulse energy confined in the 0.87-nm 3-dB spectral bandwidth, this MOPA is also a promising source for nonlinear frequency conversion to generate high-energy pulses in other spectral regions. We have explored the pulse energy scaling until the stimulated Raman Scattering (SRS) becomes significant (i.e. spectral peak intensity exceeds 1% of that of the signal).

200 W Diffraction limited, single-polarization, all-fiber picosecond MOPA.

A fully fiberized, single-polarization, gain-switched diode-seeded fiber master oscillator power amplifier (MOPA) system is demonstrated delivering 28 ps pulses at variable repetition frequencies ranging from 53 MHz up to 858 MHz. An average signal output power of 200 W was achieved with good OSNR for all operating frequencies. A maximum pulse energy of 3.23 µJ at a repetition frequency of 53 MHz was achieved, corresponding to a pulse peak power of 107 kW. The extraction of higher pulse energy was limited primarily by the onset of nonlinear effects such as SRS which lead to compromised pulse quality at higher peak powers.

Ultrawide-range four-wave mixing in Raman distributed-feedback fiber lasers.

We report ultrawide-range and highly efficient wavelength conversion by exploiting four-wave mixing (FWM) in Raman distributed-feedback (R-DFB) fiber lasers. The lasers are 30 cm long center π phase-shifted DFB gratings UV written in commercially available germano-silica (Ge/Si) single-mode fibers (PS980 from Fibercore Ltd., and UHNA4 from Nufern). The R-DFB lasing signal acts as a pump wave for the FWM process within the DFB cavity, and the obtained FWM conversion efficiency is around -25 dB with a maximum wavelength conversion range of 112 nm.