CH3NH3PbI3 films prepared by combining 1- and 2-step deposition: how crystal growth conditions affect properties.

Perovskite solar cells continue to attract strong attention because of their unprecedented rate of power conversion efficiency increase. CH3NH3PbI3 (MAPbI3) is the most widely studied perovskite. Typically one-step (1-s) or two-step (2-s) deposition methods are used to prepare MAPbI3 films. Here, we investigate a new MAPbI3 film formation method that combines 1-s and 2-s deposition (termed 1 & 2-s) and uses systematic variation of the stoichiometric mole ratio (x) for the PbI2 + xMAI solutions employed. The PbI2 + xMAI solutions were used to deposit precursor films that were subsequently dipped in MAI solution as a second step to produce the final MAPbI3 films. The morphologies of the 1 & 2-s MAPbI3 films consisted of three crystal types: tree-like microcrystals (≫1 µm), cuboid meso-crystals (∼0.1-1 µm) and nanocrystals (∼50-80 nm). Each crystal type and their proportions were controlled by the value for x. The new 1 & 2-s deposition method produced MAPbI3 films with tuneable optoelectronic properties that were related to those for the conventional 1-s and 2-s films. However, the 1 & 2-s film properties were not simply a combination of those for the 1-s and 2-s films. The 1 & 2-s films showed enhanced light scattering and the photoluminescence spectra displayed a morphologically-dependent red-shift. The unique morphologies for the 1 & 2-s films also strongly influenced PbI2 conversion, power conversion efficiency, hysteresis and recombination. The trends for the performance parameters and hysteresis were compared for devices constructed using spiro-MeOTAD and P3HT and were similar. The 1 & 2-s method should apply to other perovskite formulations and the new insights concerning MAPbI3 crystal growth conditions, morphology and material properties established in this study should also be transferable.

The Role of Oxygen in the Degradation of Methylammonium Lead Trihalide Perovskite Photoactive Layers.

In this paper we report on the influence of light and oxygen on the stability of CH3 NH3 PbI3 perovskite-based photoactive layers. When exposed to both light and dry air the mp-Al2 O3 /CH3 NH3 PbI3 photoactive layers rapidly decompose yielding methylamine, PbI2 , and I2 as products. We show that this degradation is initiated by the reaction of superoxide (O2 (-) ) with the methylammonium moiety of the perovskite absorber. Fluorescent molecular probe studies indicate that the O2 (-) species is generated by the reaction of photoexcited electrons in the perovskite and molecular oxygen. We show that the yield of O2 (-) generation is significantly reduced when the mp-Al2 O3 film is replaced with an mp-TiO2 electron extraction and transport layer. The present findings suggest that replacing the methylammonium component in CH3 NH3 PbI3 to a species without acid protons could improve tolerance to oxygen and enhance stability.

Stability of Lead and Tin Halide Perovskites: The Link between Defects and Degradation.

The field of photovoltaic research has been lately dominated by the rapid evolution of low-cost and high-efficiency hybrid organic lead halide perovskite solar cells. Despite the considerable progress made in the efficiency of such devices, the achievement of long-term material and device stability remains a challenge. In this Perspective, insights into the role structural defects play in the stability of these perovskite absorbers are examined, highlighting the critical importance of vacancy type defects as the initiation sites for moisture-, oxygen-, and light-induced degradation and the approaches that are emerging to help overcome these issues. In the second part of the Perspective we consider the stability of tin-based perovskites. Here, the Sn4+ defects that arise upon material degradation are described along with the strategies being developed to enhance stability and decrease their formation. Finally, the discussion is extended to innately more stable layered tin-based perovskites, identifying them as a route to the development of efficient lead-free perovskite solar cells.

Toward Improved Environmental Stability of Polymer:Fullerene and Polymer:Nonfullerene Organic Solar Cells: A Common Energetic Origin of Light- and Oxygen-Induced Degradation.

With the emergence of nonfullerene electron acceptors resulting in further breakthroughs in the performance of organic solar cells, there is now an urgent need to understand their degradation mechanisms in order to improve their intrinsic stability through better material design. In this study, we present quantitative evidence for a common root cause of light-induced degradation of polymer:nonfullerene and polymer:fullerene organic solar cells in air, namely, a fast photo-oxidation process of the photoactive materials mediated by the formation of superoxide radical ions, whose yield is found to be strongly controlled by the lowest unoccupied molecular orbital (LUMO) levels of the electron acceptors used. Our results elucidate the general relevance of this degradation mechanism to both polymer:fullerene and polymer:nonfullerene blends and highlight the necessity of designing electron acceptor materials with sufficient electron affinities to overcome this challenge, thereby paving the way toward achieving long-term solar cell stability with minimal device encapsulation.

Fast oxygen diffusion and iodide defects mediate oxygen-induced degradation of perovskite solar cells.

Methylammonium lead halide perovskites are attracting intense interest as promising materials for next-generation solar cells, but serious issues related to long-term stability need to be addressed. Perovskite films based on CH3NH3PbI3 undergo rapid degradation when exposed to oxygen and light. Here, we report mechanistic insights into this oxygen-induced photodegradation from a range of experimental and computational techniques. We find fast oxygen diffusion into CH3NH3PbI3 films is accompanied by photo-induced formation of highly reactive superoxide species. Perovskite films composed of small crystallites show higher yields of superoxide and lower stability. Ab initio simulations indicate that iodide vacancies are the preferred sites in mediating the photo-induced formation of superoxide species from oxygen. Thin-film passivation with iodide salts is shown to enhance film and device stability. The understanding of degradation phenomena gained from this study is important for the future design and optimization of stable perovskite solar cells.