Eco-friendly synthesis of clay-chitosan composite for efficient removal of alizarin red S dye from wastewater: A comprehensive experimental and theoretical investigation.

Alizarin Red S (ARS) is commonly utilized for dyeing in textile industry. The dye represents a refractory pollutant in the aquatic environment unless properly treated. To tackle this pollutant, the applicability of chitosan-clay composite (3C) for the ARS removal from textile wastewater was studied. Characterization studies were conducted on the synthesized adsorbent using Fourier transformation infrared (FT-IR), X-ray diffraction (XRD), and energy dispersive X-ray (EDX) techniques. Optimized parameters such as adsorbent's dosage, pH, reaction time, and initial concentrations were tested in a batch system. Additionally, density functional theory (DFT) was calculated to understand the adsorption mechanism and the role of benzene rings and oxygen atoms in the ARS as electron donors. At the same initial concentration of 30 mg/L and optimized conditions of 50 mg of dose, pH 2, and 10 min of reaction time, about 86% of ARS removal was achieved using the composite. The pseudo-second-order kinetic was applicable to model a reasonable fitness of the adsorption reaction, while the Temkin model was representative to simulate the reaction with a maximum adsorption capacity of 44.39 mg/g. This result was higher than magnetic chitosan (40.12 mg/g), or pure chitosan (42.48 mg/g). With ΔH = 27.22 kJ/mol and ΔG<0, the data implied the endothermic and spontaneous nature of the adsorption process. Overall, this implies that the clay-chitosan composite is promising to remove target dye from contaminated wastewater.

Bio-based composite from chitosan waste and clay for effective removal of Congo red dye from contaminated water: Experimental studies and theoretical insights.

Water pollution due to dyes in the textile industry is a serious environmental problem. During the finishing stage, Congo red (CR) dye, water-soluble, is released into wastewater, polluting the water body. This study explores the effectiveness of utilizing a composite composed of Safi raw clay and chitosan to remove an anionic dye from synthetic wastewater. The chitosan was extracted from crab shells. Its removal performance was compared to that of natural clay. Both the composite and raw clay were used to remove target pollutant. The effects of the chitosan load in the composite, size particles, initial dye concentration, contact time, pH, and temperature on the dye's elimination were tested in batch modes. The composite with 30% (w/w) of chitosan exhibited the highest dye removal. At pH 2, an adsorption capacity of 84.74 mg/g was achieved, indicating that the grafting of the polymer onto clay surface enhances its efficacity and stability in acidic environments. This finding was supported by characterization data obtained from X-ray diffraction (XRD), scanning electron microscopy (SEM), dispersive X-ray spectroscopy (EDX), and Fourier transform infrared (FT-IR) analyses. Under optimized conditions of 20 mg dose, pH 2, 30 min of reaction time, and 20 mg/L of dye concentration, about 92% of dye removal was achieved. The Langmuir isotherm model represents dye adsorption by the composite, while dye removal was controlled by pseudo-second-order model. Thermodynamic data of the adsorption (ΔH = +8.82 kJ/mol; ΔG <0) suggested that the dye adsorption was spontaneous and endothermic. The findings provide insights into the dye elimination by the adsorbent, indicating that the removal occurred via attractive colombic forces, as confirmed by density functional theory (DFT) analysis. Overall, the composite of natural clays and chitosan waste is a promising and innovative adsorbent for treating wastewater containing recalcitrant dyes.

Leveraging food waste for electricity: A low-carbon approach in energy sector for mitigating climate change and achieving net zero emission in Hong Kong (China).

In recent years, food waste has been a global concern that contributes to climate change. To deal with the rising impacts of climate change, in Hong Kong, food waste is converted into electricity in the framework of low-carbon approach. This work provides an overview of the conversion of food waste into electricity to achieve carbon neutrality. The production of methane and electricity from waste-to-energy (WTE) conversion are determined. Potential income from its sale and environmental benefits are also assessed quantitatively and qualitatively. It was found that the electricity generation from the food waste could reach 4.33 × 109 kWh annually, avoiding equivalent electricity charge worth USD 3.46 × 109 annually (based on US' 8/kWh). An equivalent CO2 mitigation of 9.9 × 108 kg annually was attained. The revenue from its electricity sale in market was USD 1.44×109 in the 1st year and USD 4.24 ×109 in the 15th year, respectively, according to the projected CH4 and electricity generation. The modelling study indicated that the electricity production is 0.8 kWh/kg of landfilled waste. The food waste could produce electricity as low as US' 8 per kW ∙ h. In spite of its promising results, there are techno-economic bottlenecks in commercial scale production and its application at comparable costs to conventional fossil fuels. Issues such as high GHG emissions and high production costs have been determined to be resolved later. Overall, this work not only leads to GHG avoidance, but also diversifies energy supply in providing power for homes in the future.

Tackling microplastics pollution in global environment through integration of applied technology, policy instruments, and legislation.

Microplastic pollution is a serious environmental problem that affects both aquatic and terrestrial ecosystems. Small particles with size of less than 5 mm, known as microplastics (MPs), persist in the environment and pose serious threats to various species from micro-organisms to humans. However, terrestrial environment has received less attention than the aquatic environment, despite being a major source of MPs that eventually reaches water body. To reflect its novelty, this work aims at providing a comprehensive overview of the current state of MPs pollution in the global environment and various solutions to address MP pollution by integrating applied technology, policy instruments, and legislation. This review critically evaluates and compares the existing technologies for MPs detection, removal, and degradation, and a variety of policy instruments and legislation that can support the prevention and management of MPs pollution scientifically. Furthermore, this review identifies the gaps and challenges in addressing the complex and diverse nature of MPs and calls for joint actions and collaboration from stakeholders to contain MPs. As water pollution by MPs is complex, managing it effectively requires their responses through the utilization of technology, policy instruments, and legislation. It is evident from a literature survey of 228 published articles (1961-2023) that existing water technologies are promising to remove MPs pollution. Membrane bioreactors and ultrafiltration achieved 90% of MPs removal, while magnetic separation was effective at extracting 88% of target MPs from wastewater. In biological process, one kg of wax worms could consume about 80 g of plastic/day. This means that 100 kg of wax worms can eat about 8 kg of plastic daily, or about 2.9 tons of plastic annually. Overall, the integration of technology, policy instrument, and legislation is crucial to deal with the MPs issues.

A critical review on the electrosorption of organic compounds in aqueous effluent - Influencing factors and engineering considerations.

Despite being an old process from the end of the 19th century, electrosorption has attracted renewed attention in recent years because of its unique properties and advantages compared to other separation technologies and due to the concomitant development of new porous electrode materials. Electrosorption offer the advantage to separate the pollutants from wastewater with the possibility of selectively adsorbing and desorbing the targeted compounds. A comprehensive review of electrosorption is provided with particular attention given to the electrosorption of organic compounds, unlike existing capacitive deionization review papers that only focus on inorganic salts. The background and principle of electrosorption are first presented, while the influence of the main parameters (e.g., electrode materials, electrode potential, physico-chemistry of the electrolyte solutions, type of compounds, co-sorption effect, reactor design, etc.) is then detailed and the modeling and engineering aspects are discussed. Finally, the main output and future prospects about recovery studies and combination between electro-sorption/desorption and degradation processes are given. This review particularly highlights that carbon-based materials have been mostly employed (85% of studies) as porous electrode in organics electrosorption, while existing studies lack of electrode stability and durability tests in real conditions. These electrodes have been implemented in a fixed-bed reactor design most of the time (43% of studies) due to enhanced mass transport. Moreover, the electrode potential is a major criterion: it should be applied in the non-faradaic domain otherwise unwanted reactions can easily occur, especially the corrosion of carbon from 0.21 V/standard hydrogen electrode or the water oxidation/reduction. Furthermore, there is lack of studies performed with actual effluents and without addition of supporting electrolyte, which is crucial for testing the real efficiency of the process. The associated predictive model will be required by considering the matrix effect along with transport phenomena and physico-chemical characteristics of targeted organic compounds.

Adsorption of Crystal Violet onto an Agricultural Waste Residue: Kinetics, Isotherm, Thermodynamics, and Mechanism of Adsorption.

Agricultural waste can be exploited for the adsorption of dyes, due to their low cost, availability, cost-effectiveness, and efficiency. In this study, we were interested in the elimination of crystal violet dye, from aqueous solutions, by adsorption on almond shell-based material, as a low-cost and ecofriendly adsorbent. The almond shells were first analyzed by Fourier transform infrared spectroscopy (FTIR) and X-ray diffraction; then, the influence of adsorbent dose, initial dye concentration time, and pH were studied to assess adsorption capacity under optimal experimental conditions. Experimental results indicate that almond shell adsorbent removes about 83% of the dye from the solutions at room temperature and in batch mode; the kinetic study showed that the equilibrium time is about 90 min, and the model of pseudo-second order could very well describe adsorption kinetics. The modulation of adsorption isotherms showed that retention follows the Langmuir model. The thermodynamic study has shown that the adsorption is endothermic (ΔH° > 0) and spontaneous (ΔG° < 0).

Characterization by fluorescence of dissolved organic matter in rural drinking water storage tanks in Morocco.

Water storage tanks, fed directly from the river through opened channels, are particular systems used for water supply in rural areas in Morocco. The stored water is used as drinking water by the surrounding population without any treatment. UV-visible spectroscopy and fluorescence spectroscopy (excitation-emission matrices and synchronous fluorescence) have been tested as rapid methods to assess the quality of the water stored in the reservoirs as well as along the river feeding them. Synchronous fluorescence spectra (SFS50), collected with a difference of 50 nm between excitation and emission wavelengths, revealed a high tryptophan-like fluorescence, indicative of a pollution induced by untreated domestic and/or farm wastewater. The best correlations were obtained between the total SFS50 fluorescence and dissolved organic carbon (DOC) and biological oxygen demand, showing that the contribution of humic-like fluorescent substances cannot be neglected to rapidly assess reservoir water quality in terms of DOC by fluorescence spectroscopy.

The effect of graphene oxide administration on the brains of male mice: Behavioral study and assessment of oxidative stress.

Graphene oxide (GO) nanoparticles are attracting growing interest in various fields, not least because of their distinct characteristics and possible uses. However, concerns about their impact on neurological health are emerging, underlining the need for in-depth studies to assess their neurotoxicity. This study examines GO exposure's neurobehavioral and biochemical effects on the central nervous system (CNS). To this end, we administered two doses of GO (2 and 5 mg/kg GO) to mice over a 46-day treatment period. We performed a battery of behavioral tests on the mice, including the open field to assess locomotor activity, the maze plus to measure anxiety, the pole test to assess balance and the rotarod to measure motor coordination. In parallel, we analyzed malondialdehyde (MDA) levels and catalase activity in the brains of mice exposed to GO nanoparticles. In addition, X-ray energy dispersive (EDX) analysis was performed to determine the molecular composition of the brain. Our observations reveal brain alterations in mice exposed to GO by intraperitoneal injection, demonstrating a dose-dependent relationship. We identified behavioral alterations in mice exposed to GO, such as increased anxiety, decreased motor coordination, reduced locomotor activity and balance disorders. These changes were dose-dependent, suggesting a correlation between the amount of GO administered and the extent of behavioral alterations. At the same time, a dose-dependent increase in malondialdehyde and catalase activity was observed, reinforcing the correlation between exposure intensity and associated biochemical responses.

Digitalization and innovation in green ports: A review of current issues, contributions and the way forward in promoting sustainable ports and maritime logistics.

As a fundamental transportation mode, maritime logistics has become an indispensable component on a global scale. However, there are multiple drawbacks associated with ports operating in traditional ways, such as higher cost, lower efficiency and generating more environmental pollution. Digital technologies have been researched and implemented gradually in green ports, especially in data collection and real-time monitoring, and these advances help to promote higher work efficiency and reduce detrimental environmental impacts. It was found that green ports (e.g. ports of Raffina, Los Angeles, and Long Beach) generally perform better in energy conservation and pollutant emission reduction. However, considering the variability in the level of digitalization, there are challenges in achieving effective communications between individual ports. Therefore, to optimize and update green port practices, a systematic review is necessary to comprehensively analyze the beneficial contributions of green ports. This review adopted bibliometric analysis to examine the shipping framework focusing on green ports digitalization and innovation. After that, with regards to the bibliometric results, five aspects were analyzed, including environment, performance, policy, technology, and management. Besides, intelligent life-cycle management was systematically discussed to improve green ports and maritime logistics performance and sustainability in three aspects, namely waste discharge, shipping management system and green ports management. The findings revealed that green ports and maritime logistics require digital cooperation, transformation, and management to achieve sustainable development goals, including route selection and control of ships' numbers, weather prediction, and navigational effluent monitoring, albeit with some obstacles.

Fixed-bed adsorption of pesticide agricultural waste using cross-linked adsorptive hydrogel composite beads.

Adsorption column blockage due to solid adsorbent material is prevalent in laboratory-scale applications. Creating composite materials with stable geometries offers a viable solution. By crafting hydrogel beads using sodium alginate (Alg) and a bio-source like activated carbon (RMCA-P), it becomes possible to effectively eliminate agricultural pollutants, including the pesticide 2,4-D, from aqueous solutions. To evaluate the performance of these beads, a range of structural and textural analyses such as DRX, FTIR, SEM/EDX, BET, Zeta potential, Boehm titration, and iodine number were employed. Moreover, the study found that optimizing certain parameters greatly enhanced adsorption column efficiency. Specifically, increasing the bed height while reducing the flow rate of the adsorbate and the initial concentration in the inlet proved beneficial. The column demonstrated peak performance at a flow rate of 0.5 mL/min, a bed height of 35 cm, and an inlet adsorbate concentration of 50 mg/L. Under these conditions, the highest recorded removal rate for 2,4-D was 95.49%, which was subsequently confirmed experimentally at 95.05%. Both the Thomas and Yoon-Nelson models exhibited a good fit with the breakthrough curves. After undergoing three cycles of reuse, the RMCA-P/Alg hydrogel composite maintained a 2,4-D removal percentage of 74.21%. Notably, the RMCA-P/Alg beads exhibited effective removal of 2,4-D from herbicidal field waters in a continuous operational mode.

Ameliorative effect of Ononis natrix against chronic lead poisoning in mice: neurobehavioral, biochemical, and histological study.

Lead (Pb) is one of the most common heavy metals with toxicological effects on many tissues in humans as well as animals. In order to counteract the toxic effects of this metal, the administration of synthetic or natural antioxidants is thus required. The aim of this study was to examine the beneficial effect of the aqueous extract of Ononis natrix (AEON) against lead acetate-induced damage from a behavioral, biochemical, and histological point of view. Forty-eight male mice were divided into four equal groups: Ctr (control); Pb (lead acetate 1g/l); Pb + On 100 mg/kg (lead acetate 1 g/l + AEON 100 mg/kg); Pb + On 500 mg/kg (lead acetate 1 g/l + AEON 500 mg/kg). AEON was administered orally from day 21 after the start of lead exposure up to the end of the experiment. The results revealed that lead induced behavioral disorders, increased serum levels of liver markers (AST, ALT, and bilirubin), as well as kidney markers (urea and creatinine). At the same time, levels of thiobarbituric acid reactive substances (TBARS) and glutathione peroxidase (GPx) increased significantly. Moreover, Pb caused structural changes in the liver and kidneys of Pb-exposed mice. However, AEON administration significantly improved all lead-induced brain, liver, and kidney dysfunctions. Our results suggest that AEON could be a source of molecules with therapeutic potential against brain, liver, and kidney abnormalities caused by lead exposure.

Monitoring of toxic cyanobacterial blooms in Lalla Takerkoust reservoir by satellite imagery and microcystin transfer to surrounding farms.

Cyanobacterial harmful algal blooms (CyanoHABs) threaten public health and freshwater ecosystems worldwide. In this study, our main goal was to explore the dynamics of cyanobacterial blooms and how microcystins (MCs) move from the Lalla Takerkoust reservoir to the nearby farms. We used Landsat imagery, molecular analysis, collecting and analyzing physicochemical data, and assessing toxins using HPLC. Our investigation identified two cyanobacterial species responsible for the blooms: Microcystis sp. and Synechococcus sp. Our Microcystis strain produced three MC variants (MC-RR, MC-YR, and MC-LR), with MC-RR exhibiting the highest concentrations in dissolved and intracellular toxins. In contrast, our Synechococcus strain did not produce any detectable toxins. To validate our Normalized Difference Vegetation Index (NDVI) results, we utilized limnological data, including algal cell counts, and quantified MCs in freeze-dried Microcystis bloom samples collected from the reservoir. Our study revealed patterns and trends in cyanobacterial proliferation in the reservoir over 30 years and presented a historical map of the area of cyanobacterial infestation using the NDVI method. The study found that MC-LR accumulates near the water surface due to the buoyancy of Microcystis. The maximum concentration of MC-LR in the reservoir water was 160 µg L-1. In contrast, 4 km downstream of the reservoir, the concentration decreased by a factor of 5.39 to 29.63 µgL-1, indicating a decrease in MC-LR concentration with increasing distance from the bloom source. Similarly, the MC-YR concentration decreased by a factor of 2.98 for the same distance. Interestingly, the MC distribution varied with depth, with MC-LR dominating at the water surface and MC-YR at the reservoir outlet at a water depth of 10 m. Our findings highlight the impact of nutrient concentrations, environmental factors, and transfer processes on bloom dynamics and MC distribution. We emphasize the need for effective management strategies to minimize toxin transfer and ensure public health and safety.

Quality and disinfection trials of consumption water in storage reservoirs for rural area in the Marrakech region (Assif El Mal).

Traditional reservoirs for water storage are important systems of water supply in rural areas of Morocco. These reservoirs are fed by rainwater and/or directly from rivers through open channels; the stored water is used without any treatment as drinking water by the surrounding population. The present study aimed to assess the physicochemical and bacteriological quality of stored water and the corresponding sediment in six traditional reservoirs (R1 to R6) located in the rural municipality of Assif El Mal. We tested two inexpensive methods of disinfecting the stored water: chlorination and solar disinfection in bottles. The results show a rise of organic and mineral concentrations. Regarding bacteriological quality, a critical contamination level was detected (8 × 10(5) CFU/100 ml in water and 9 × 10(7) CFU/g in sediment) according to the 2002 Moroccan Standards for drinking water (0 CFU/100 ml). In the disinfection tests, chlorine disinfection removed all studied germs after just 1 hour, and the solar exposure process removed the majority of bacteria (after 3 hours) except those with a resistant form (Clostridia).

Low-cost materials as vehicles for pesticides in aquatic media: a review of the current status of different biosorbents employed, optimization by RSM approach.

Water contamination by pesticides is increasing dramatically due to population growth and the extensive use of pesticides in agriculture, leading to grave environmental and health concerns. Thus, efficient processes and the design and development of effective treatment technologies are required due to the enormous demand for fresh water. The adsorption approach has been widely used to remove organic contaminants such as pesticides because of its performance, less expense, high selectivity, and simplicity of operation compared to other treatment technologies. Among alternative adsorbents, biomaterials abundantly available for pesticide sorption from water resources have attracted the attention of researchers worldwide. The main objective of this review article is to (i) present studies on a wide range of raw or chemically modified biomaterials potentially effective in removing pesticides from aqueous media; (ii) indicating the effectiveness of biosorbents as green and low-cost materials for removing pesticides from wastewater; and (iii) furthermore, report the application of response surface methodology (RSM) for modeling and optimizing adsorption.

A novel hydrogel beads based copper-doped Cerastoderma edule shells@Alginate biocomposite for highly fungicide sorption from aqueous medium.

The engineering of a novel biocomposite based on Cerastoderma edule shells doped with copper and alginate (Ce-Cu@Alg) forming hydrogel beads was used for batch and dynamic adsorption thiabendazole (TBZ) pesticide from water. The prepared biosorbent was analyzed by various characterization techniques such as scanning electron microscopy (SEM), X-ray diffraction analysis (XRD), Brunauer-Emmett-Teller analysis (BET), and energy dispersive spectroscopy (EDS), thermogravimetric and differential analysis (TGA-DTA). The results of the TBZ batch biosorption by Ce-Cu@Alg composite showed that the Langmuir model was the most adequate to describe the adsorption process, with a maximum adsorption capacity value of 21.98 mg/g. Moreover, the adsorption kinetics were adjusted by the pseudo-second-order model. The optimal conditions determined by the RSM approach coupled with the CCD design were 100 ppm of initial TBZ concentration, a Ce-Cu@Alg beads dose of 6 g/L and a contact time of 180 min for maximum removal of 83.42%. On the other hand, the TBZ sorption on a fixed bed of Ce-Cu@Alg beads was effective at high column height, low effluent flow and low solution concentration. The Thomas model was best fitted to the kinetic data. This study shows the possibility of using this new hybrid biocomposite in the industrial sector to treat large effluent volumes.

Phenolic compounds removal in table olive processing wastewater by column adsorption: conditions' optimization.

The annual production of wastewater from the olive table industry poses a serious problem owing to its high organic matter load, which is highly concentrated in phenolic compounds (PCs) and inorganic materials. This research used adsorption to recover PCs from table olive wastewater (TOWW). Activated carbon was employed as a novel adsorbent. The activated carbon was obtained from olive pomace (OP) and activated using a chemical agent (ZnCl2). Fourier transform infrared spectroscopy analysis (FTIR), Brunauer-Emmett-Teller analysis (BET), scanning electron microscopy (SEM), and energy-dispersive X-ray spectroscopy (EDS) were applied to characterize the activated carbon sample. To optimize the biosorption conditions of PCs (adsorbent dose (A), temperature (B), and time (C)), a central composite design (CCD) model was used. An adsorption capacity was 1952.34 mg g-1 for optimal conditions with an activated carbon dose of 0.569 g L-1, a temperature of 39 °C, and a contact time of 239 min. The pseudo-second-order and Langmuir models as kinetic and isothermal mathematical models were proved to be more appropriate for the interpretation of the adsorption phenomenon of PCs. PC recovery was performed in fixed-bed reactors. The results of the adsorption of PCs from TOWW by activated carbon could be an effective process at a low cost.

A Comprehensive Review of Polysaccharide-Based Hydrogels as Promising Biomaterials.

Polysaccharides have emerged as a promising material for hydrogel preparation due to their biocompatibility, biodegradability, and low cost. This review focuses on polysaccharide-based hydrogels' synthesis, characterization, and applications. The various synthetic methods used to prepare polysaccharide-based hydrogels are discussed. The characterization techniques are also highlighted to evaluate the physical and chemical properties of polysaccharide-based hydrogels. Finally, the applications of SAPs in various fields are discussed, along with their potential benefits and limitations. Due to environmental concerns, this review shows a growing interest in developing bio-sourced hydrogels made from natural materials such as polysaccharides. SAPs have many beneficial properties, including good mechanical and morphological properties, thermal stability, biocompatibility, biodegradability, non-toxicity, abundance, economic viability, and good swelling ability. However, some challenges remain to be overcome, such as limiting the formulation complexity of some SAPs and establishing a general protocol for calculating their water absorption and retention capacity. Furthermore, the development of SAPs requires a multidisciplinary approach and research should focus on improving their synthesis, modification, and characterization as well as exploring their potential applications. Biocompatibility, biodegradation, and the regulatory approval pathway of SAPs should be carefully evaluated to ensure their safety and efficacy.

Insight into microwave-assisted synthesis of the chitosan-MOF composite: Pb(II) adsorption.

Heavy metal contamination has increased over the globe, causing significant environmental issues owing to direct and indirect releases into water bodies. As a result, metal removal from water entities must be addressed soon. Various adsorbents such as MOFs and chitosan have demonstrated promising results in water treatment. The present study prepared a composite material (chitosan-UiO-66-glycidyl methacrylate MOF) by a microwave-assisted method. The structure and morphology of the chitosan-MOF composite were studied using FE-SEM, EDX, XRD, BET, FT-IR, and TGA techniques. In addition, the adsorption of Pb(II) from aqueous solution onto the chitosan-MOF composite was analyzed in a batch study concerning pH, contact time, initial metal ion concentration, and adsorbent dosage. The composite has a large surface area of 867 m2/g with a total pore volume of 0.51 cm3/g and thermal stability of up to 400 [Formula: see text]. Following an analysis of the adsorption isotherms, kinetics, and thermodynamics, the Langmuir model showed an excellent fit with the adsorption data (R2 = 0.99) and chi-squared (X2 = 3.609). The adsorption process was a spontaneous exothermic reaction and the pseudo-second-order rate equation fitted the kinetic profile well. Moreover, the composite is recyclable, retaining 83.45% of its removal effectiveness after 5 consecutive cycles, demonstrating it as a sustainable adsorbent for metal recovery. This study introduces a novel synthesized composite with enhanced recyclability and a higher potential for eliminating pollutants from industrial wastewater.

Continuous treatment of highly concentrated tannery wastewater using novel porous composite beads: Central composite design optimization study.

This present study depicts the successful employment of fixed-bed column for total chromium removal from tannery wastewater in dynamic mode using sodium alginate-powdered marble beads (SA-Marble) as adsorbent. The SA-Marble composite beads prepared were characterized by Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS) and Brunauer, Emmett and Teller (BET) method. The adsorption process performance of this bio-sorbent was examined in batches and columns for real effluent (tannery wastewater). After 90 min, the total chromium removal efficiency could be kept above 90% in the batch experiment. The adsorption kinetics fit better with the pseudo-second-order model, indicating the chemisorption process and the adsorption capacity of about 67.74 mg g-1 at 293 K (C0 = 7100 mg L-1) was obtained. Additionally, dynamic experiments indicate that the total chromium removal efficiency could be maintained above 90% after 120 min at 293 K and 60 min at 318 and 333 K; it's an endothermic but rapid process. The effects of two adsorption variables (Temperature and time) were investigated using central composite design (CCD), which is a subset of response surface methodology (total Cr, COD, sulfate, and total phosphorus percentage removal). This work paves a new avenue for synthesizing SA-Marble composite beads and provides an adsorption efficiency of total chromium removal from tannery wastewater.

Sub-acute toxicity of graphene oxide (GO) nanoparticles in male mice after intraperitoneal injection: Behavioral study and histopathological evaluation.

Graphene oxide (GO) is a graphene derivative used for numerous applications in which biomedical uses are significant. However, for this application, the security of GO is doubtful. In this work, we synthesized this nanoparticle to assess its toxicity in male mice. In addition, we studied the effects of this nanomaterial on behavior by administering GO intraperitoneally to mice at different doses (2 mg/kg and 5 mg/kg) for five days. Subsequently, we performed biochemical analyses of blood serum and measured peroxidase and malondialdehyde (MDA) activity. Then, we performed histological sections to evaluate the brain's and liver's pathological and morphological changes. The data showed that the open field tests did not alter the locomotor activity. Furthermore, the elevated cross-maze tests showed no anxiety effect in the GO doses in the animals. The biochemical analyses indicated that GO influenced the level of biochemical parameters. Although, the oxidative stress assay showed an increase in peroxidase and MDA activity after GO intoxication. However, histopathological analysis of liver sections showed that GO caused liver inflammation, whereas, at the brain level, GO did not affect neuronal cells. The results indicate that GO caused toxic effects and that its toxicity could be mediated by oxidative stress.