Emulsion Stabilized by Biocompatible and Stimuli-Responsive Poly(N-vinylcaprolactam)-Based Microgels: Effects of Electrostatic Repulsion and Deformability on Emulsion Stability.

Microgels have been widely used for stabilizing emulsions due to their softness and stimulus responsiveness. Although ultrastable emulsions have been prepared by microgel nanoparticles, the role of electrostatic interactions on emulsion stability is still a controversial topic and further investigation of the effect of microgel deformability is required. In the present study, neutral poly(N-vinylcaprolactam) (PVCL) and charged poly(N-vinylcaprolactam)-co-methacrylic acid (P(VCL-co-MAA)) microgels were synthesized and further used as emulsifiers to stabilizing emulsion. The P(VCL-co-MAA) microgel has a swelling ratio larger than that of the PVCL microgel in water. The nanomechanical properties of the microgels in water were characterized by atomic force microscopy with using the tip of different radii. The result reveals that the P(VCL-co-MAA) microgel is more deformable than the PVCL counterpart. Stability tests of the emulsions showed that below the volume phase transition temperature (VPTT) of the microgels, both microgel types can stabilize the emulsions under various conditions. Unexpectedly, most of the emulsions still remain stable above the VPTT. Further increasing the temperature to 60 °C, P(VCL-co-MAA) microgel emulsions remained stable at a pH value above the pKa of MAA while the emulsion was unstable below the pKa. However, phase separation occurs in PVCL microgel-stabilized emulsions at 60 °C. These results demonstrate that electrostatic repulsion and deformability of the microgels can enhance the emulsion stability, providing insights into the rational design and preparation of ultrastable Pickering emulsions.

Effects of Gas Layer Thickness on Capillary Interactions at Superhydrophobic Surfaces.

Strongly attractive forces act between superhydrophobic surfaces across water due to the formation of a bridging gas capillary. Upon separation, the attraction can range up to tens of micrometers as the gas capillary grows, while gas molecules accumulate in the capillary. We argue that most of these molecules come from the pre-existing gaseous layer found at and within the superhydrophobic coating. In this study, we investigate how the capillary size and the resulting capillary forces are affected by the thickness of the gaseous layer. To this end, we prepared superhydrophobic coatings with different thicknesses by utilizing different numbers of coating cycles of a liquid flame spraying technique. Laser scanning confocal microscopy confirmed an increase in gas layer thickness with an increasing number of coating cycles. Force measurements between such coatings and a hydrophobic colloidal probe revealed attractive forces caused by bridging gas capillaries, and both the capillary size and the range of attraction increased with increasing thickness of the pre-existing gas layer. Hence, our data suggest that the amount of available gas at and in the superhydrophobic coating determines the force range and capillary growth.

The dynamic nature of natural and fatty acid modified calcite surfaces.

Calcium carbonate, particularly in the form of calcite, is an abundant mineral widely used in both human-made products and biological systems. The calcite surface possesses a high surface energy, making it susceptible to the adsorption of organic contaminants. Moreover, the surface is also reactive towards a range of chemicals, including water. Consequently, studying and maintaining a clean and stable calcite surface is only possible under ultrahigh vacuum conditions and for limited amounts of time. When exposed to air or solution, the calcite surface undergoes rapid transformations, demanding a comprehensive understanding of the properties of calcite surfaces in different environments. Similarly, attention must also be directed towards the kinetics of changes, whether induced by fluctuating environments or at constant condition. All these aspects are encompassed in the expression "dynamic nature", and are of crucial importance in the context of the diverse applications of calcite. In many instances, the calcite surface is modified by adsorption of fatty acids to impart a desired nonpolar character. Although the binding between carboxylic acid groups and calcite surfaces is strong, the fatty acid layer used for surface modification undergoes significant alterations when exposed to water vapour and liquid water droplets. Therefore, it is also crucial to understand the dynamic nature of the adsorbed layer. This review article provides a comprehensive overview of the current understanding of both the dynamics of the calcite surface as well as when modified by fatty acid surface treatments.

Calcite Surfaces Modified with Carboxylic Acids (C2 to C18): Layer Organization, Wettability, Stability, and Molecular Structural Properties.

A fundamental understanding of the interactions between mineral surfaces and amphiphilic surface modification agents is needed for better control over the production and uses of mineral fillers. Here, we controlled the carboxylic acid layer formation conditions on calcite surfaces with high precision via vapor deposition. The properties of the resulting carboxylic acid layers were analyzed using surface-sensitive techniques, such as atomic force microscopy (AFM), contact angle measurements, angle resolved X-ray photoelectron spectroscopy (XPS), and vibrational sum-frequency spectroscopy. A low wettability was achieved with long hydrocarbon chain carboxylic acids such as stearic acid. The stearic acid layer formed by vapor deposition is initially patchy, but with increasing vapor exposure time, the patches grow and condense into a homogeneous layer with a thickness close to that expected for a monolayer as evaluated by AFM and XPS. The build-up process of the layer occurs more rapidly at higher temperatures due to the higher vapor pressure. The stability of the deposited fatty acid layer in the presence of a water droplet increases with the chain length and packing density in the adsorbed layer. Vibrational sum frequency spectroscopy data demonstrate that the stearic acid monolayers on calcite have their alkyl chains in an all-trans conformation and are anisotropically distributed on the plane of the surface, forming epitaxial monolayers. Vibrational spectra also show that the stearic acid molecules interact with the calcite surface through the carboxylic acid headgroup in both its protonated and deprotonated forms. The results presented provide new molecular insights into the properties of adsorbed carboxylic acid layers on calcite.

Temperature-Dependent Nanomechanical Properties of Adsorbed Poly-NIPAm Microgel Particles Immersed in Water.

The temperature dependence of nanomechanical properties of adsorbed poly-NIPAm microgel particles prepared by a semibatch polymerization process was investigated in an aqueous environment via indentation-based atomic force microscopy (AFM) methods. Poly-NIPAm microgel particles prepared by the classical batch process were also characterized for comparison. The local mechanical properties were measured between 26 and 35 °C, i.e., in the temperature range of the volume transition. Two different AFM tips with different shapes and end radii were utilized. The nanomechanical properties measured by the two kinds of tips showed a similar temperature dependence of the nanomechanical properties, but the actual values were found to depend on the size of the tip. The results suggest that the semibatch synthesis process results in the formation of more homogeneous microgel particles than the classical batch method. The methodological approach reported in this work is generally applicable to soft surface characterization in situ.

Polymer Induced Gelation of Aqueous Suspensions of Cellulose Nanocrystals.

We investigated the gelation of cellulose nanocrystals (CNCs) in polyelectrolyte and neutral polymer solutions. Cellulose nanocrystals (CNCs) with half-ester sulfate groups produced by acid hydrolysis of wood pulp were used in this study. The microstructure of CNCs/polymer suspensions was investigated in semidilute concentration regimes by selecting carboxymethyl cellulose (CMC700) as an anionic polymer and poly(ethylene oxide) (PEO600) as a neutral polymer solution. Together with quartz crystal microbalance with dissipation monitoring (QCM-D), rheology, scanning electron microscopy (SEM), and cryo-transmission electron microscopy (cryo-TEM), we characterized CNCs-polymer interactions, the suspension microstructure, and the macroscopic gel flow. Significant viscosity increases at low shear rates coupled with high shear-thinning behaviors were observed in CNC colloid-CMC700 polymer mixtures, but not those CNCs in PEO600 solutions. The apparent differences between CNCs-CMC700 and CNCs-PEO600 mixtures were due to their chain confirmations. On the basis of the evaluations from STEM, cryo-TEM, and polarized optical microscopy, we proposed that the excess CMC700 molecules in solutions result in the depletion of CNCs and the formation of anisotropic domains.

Surface-Modified and Unmodified Calcite: Effects of Water and Saturated Aqueous Octanoic Acid Droplets on Stability and Saturated Fatty Acid Layer Organization.

A profound understanding of the properties of unmodified and saturated fatty acid-modified calcite surfaces is essential for elucidating their resistance and stability in the presence of water droplets. Additional insights can be obtained by also studying the effects of carboxylic acid-saturated aqueous solutions. We elucidate surface wettability, structure, and nanomechanical properties beneath and at the edge of a deposited droplet after its evaporation. When calcite was coated by a highly packed monolayer of stearic acid, a hydrophilic region was found at the three-phase contact line. In atomic force microscopy mapping, this region is characterized by low adhesion and a topographical hillock. The surface that previously was covered by the droplet demonstrated a patchy structure of about 6 nm height, implying stearic acid reorganization into a patchy bilayer-like structure. Our data suggest that during droplet reverse dispensing and droplet evaporation, pinning of the three-phase contact line leads to the transport of dissolved fatty carboxylic acid and possibly calcium bicarbonate Ca(HCO3)2 molecules to the contact line boundary. Compared to the surface of intrinsically hydrophobic materials, such as polystyrene, the changes in contact angle and base diameter during droplet evaporation on stearic acid-modified calcite are strikingly different. This difference is due to stearic acid reorganization on the surface and transport to the water-air interface of the droplet. An effect of the evaporating droplet is also observed on unmodified calcite due to dissolution and recrystallization of the calcite surface in the presence of water. In the case where a water droplet saturated with octanoic acid is used instead of water, the stearic acid-coated calcite remains considerably more stable. Our findings are discussed in terms of the coffee-ring effect.

Nanoscale Wear and Mechanical Properties of Calcite: Effects of Stearic Acid Modification and Water Vapor.

Understanding the wear of mineral fillers is crucial for controlling industrial processes, and in the present work, we examine the wear resistance and nanomechanical properties of bare calcite and stearic acid-modified calcite surfaces under dry and humid conditions at the nanoscale. Measurements under different loads allow us to probe the situation in the absence and presence of abrasive wear. The sliding motion is in general characterized by irregular stick-slip events that at higher loads lead to abrasion of the brittle calcite surface. Bare calcite is hydrophilic, and under humid conditions, a thin water layer is present on the surface. This water layer does not affect the friction force. However, it slightly decreases the wear depth and strongly influences the distribution of wear particles. In contrast, stearic acid-modified surfaces are hydrophobic. Nevertheless, humidity affects the wear characteristics by decreasing the binding strength of stearic acid at higher humidity. A complete monolayer coverage of calcite by stearic acid results in a significant reduction in wear but only a moderate reduction in friction forces at low humidity and no reduction at 75% relative humidity (RH). Thus, our data suggest that the wear reduction does not result from a lowering of the friction force but rather from an increased ductility of the surface region as offered by the stearic acid layer. An incomplete monolayer of stearic acid on the calcite surface provides no reduction in wear regardless of the RH investigated. Clearly, the wear properties of modified calcite surfaces depend crucially on the packing density of the surface modifier and also on the air humidity.

Albumin-Hyaluronan Interactions: Influence of Ionic Composition Probed by Molecular Dynamics.

The lubrication mechanism in synovial fluid and joints is not yet fully understood. Nevertheless, intermolecular interactions between various neutral and ionic species including large macromolecular systems and simple inorganic ions are the key to understanding the excellent lubrication performance. An important tool for characterizing the intermolecular forces and their structural consequences is molecular dynamics. Albumin is one of the major components in synovial fluid. Its electrostatic properties, including the ability to form molecular complexes, are closely related to pH, solvation, and the presence of ions. In the context of synovial fluid, it is relevant to describe the possible interactions between albumin and hyaluronate, taking into account solution composition effects. In this study, the influence of Na+, Mg2+, and Ca2+ ions on human serum albumin-hyaluronan interactions were examined using molecular dynamics tools. It was established that the presence of divalent cations, and especially Ca2+, contributes mostly to the increase of the affinity between hyaluronan and albumin, which is associated with charge compensation in negatively charged hyaluronan and albumin. Furthermore, the most probable binding sites were structurally and energetically characterized. The indicated moieties exhibit a locally positive charge which enables hyaluronate binding (direct and water mediated).

Influence of the Molecular Weight and the Presence of Calcium Ions on the Molecular Interaction of Hyaluronan and DPPC.

Hyaluronan is an essential physiological bio macromolecule with different functions. One prominent area is the synovial fluid which exhibits remarkable lubrication properties. However, the synovial fluid is a multi-component system where different macromolecules interact in a synergetic fashion. Within this study we focus on the interaction of hyaluronan and phospholipids, which are thought to play a key role for lubrication. We investigate how the interactions and the association structures formed by hyaluronan (HA) and 1,2-dipalmitoyl-sn-glycero-3-phosphocholine (DPPC) are influenced by the molecular weight of the bio polymer and the ionic composition of the solution. We combine techniques allowing us to investigate the phase behavior of lipids (differential scanning calorimetry, zeta potential and electrophoretic mobility) with structural investigation (dynamic light scattering, small angle scattering) and theoretical simulations (molecular dynamics). The interaction of hyaluronan and phospholipids depends on the molecular weight, where hyaluronan with lower molecular weight has the strongest interaction. Furthermore, the interaction is increased by the presence of calcium ions. Our simulations show that calcium ions are located close to the carboxylate groups of HA and, by this, reduce the number of formed hydrogen bonds between HA and DPPC. The observed change in the DPPC phase behavior can be attributed to a local charge inversion by calcium ions binding to the carboxylate groups as the binding distribution of hyaluronan and 1,2-dipalmitoyl-sn-glycero-3-phosphocholine is not changed.