Interaction of free-base tetraphenylporphyrin with magnesium oxide: Influence of MgO morphology on metalation.

Using x-ray photoemission spectroscopy, we investigated the self-metalation of free-base tetraphenylporphyrin (2HTPP) on thin MgO(100) films on Ag(100). The deposition of one monolayer 2HTPP on MgO results in the formation of magnesium(ii) tetraphenylporphyrin (MgTPP) at room temperature. We demonstrate that the efficiency of the reaction drastically depends on the morphology of the oxide layers. The latter is changed by varying the substrate temperature during the oxide growth. We observe the complete metalation of the 2HTPP monolayer when the MgO films are grown at 393 K. The increase of the growth temperature to 573 K leads to the reduction of the percentage of metalated molecules to ∼50%. We ascribe these results to the fact that MgTPP formation takes place through the hydroxilation of steps and defects on the MgO surface, which leads to an increase of the OH component in the O 1s line.

Negative electron affinity opens quantum well in MgO layers on Ag(100).

Epitaxial MgO films on Ag(100) were studied by photoelectron spectroscopy. From the low-energy part of the spectra we obtain a negative electron affinity of about -0.9 eV. Even though electrons in the lowest conduction band are not confined by a potential barrier at the surface, quantum-well resonances are observed. The dispersion of the conduction band is determined in good agreement with theoretical calculations. Aspects of observing image-potential states predicted by theory on MgO films are discussed.

Adjusting the energy of interfacial states in organic photovoltaics for maximum efficiency.

A critical bottleneck for improving the performance of organic solar cells (OSC) is minimising non-radiative losses in the interfacial charge-transfer (CT) state via the formation of hybrid energetic states. This requires small energetic offsets often detrimental for high external quantum efficiency (EQE). Here, we obtain OSC with both non-radiative voltage losses (0.24 V) and photocurrent losses (EQE > 80%) simultaneously minimised. The interfacial CT states separate into free carriers with ≈40-ps time constant. We combine device and spectroscopic data to model the thermodynamics of charge separation and extraction, revealing that the relatively high performance of the devices arises from an optimal adjustment of the CT state energy, which determines how the available overall driving force is efficiently used to maximize both exciton splitting and charge separation. The model proposed is universal for donor:acceptor (D:A) with low driving forces and predicts which D:A will benefit from a morphology optimization for highly efficient OSC.

Unraveling the Microstructure-Related Device Stability for Polymer Solar Cells Based on Nonfullerene Small-Molecular Acceptors.

As the power conversion efficiency (PCE) of organic solar cells (OSCs) has surpassed the 17% baseline, the long-term stability of highly efficient OSCs is essential for the practical application of this photovoltaic technology. Here, the photostability and possible degradation mechanisms of three state-of-the-art polymer donors with a commonly used nonfullerene acceptor (NFA), IT-4F, are investigated. The active-layer materials show excellent intrinsic photostability. The initial morphology, in particular the mixed region, causes degradation predominantly in the fill factor (FF) under illumination. Electron traps are formed due to the reorganization of polymers and diffusion-limited aggregation of NFAs to assemble small isolated acceptor domains under illumination. These electron traps lead to losses mainly in FF, which is in contradistinction to the degradation mechanisms observed for fullerene-based OSCs. Control of the composition of NFAs close to the thermodynamic equilibrium limit while keeping adequate electron percolation and improving the initial polymer and NFA ordering are of the essence to stabilize the FF in NFA-based solar cells, which may be the key tactics to develop next-generation OSCs with high efficiency as well as excellent stability.

Overcoming efficiency and stability limits in water-processing nanoparticular organic photovoltaics by minimizing microstructure defects.

There is a strong market driven need for processing organic photovoltaics from eco-friendly solvents. Water-dispersed organic semiconducting nanoparticles (NPs) satisfy these premises convincingly. However, the necessity of surfactants, which are inevitable for stabilizing NPs, is a major obstacle towards realizing competitive power conversion efficiencies for water-processed devices. Here, we report on a concept for minimizing the adverse impact of surfactants on solar cell performance. A poloxamer facilitates the purification of organic semiconducting NPs through stripping excess surfactants from aqueous dispersion. The use of surfactant-stripped NPs based on poly(3-hexylthiophene) / non-fullerene acceptor leads to a device efficiency and stability comparable to the one from devices processed by halogenated solvents. A record efficiency of 7.5% is achieved for NP devices based on a low-band gap polymer system. This elegant approach opens an avenue that future organic photovoltaics processing may be indeed based on non-toxic water-based nanoparticle inks.