M-type refractive index profile erbium-doped fiber for high-efficiency multicore EDFA.

Cladding-pumped multicore erbium-doped fiber is an important element for future spatial division multiplexing (SDM) amplification. We propose an M-type erbium-doped multicore fiber to achieve high-efficiency SDM amplification. The performance of cladding-pumped erbium-doped fiber with a central refractive index depression has been investigated, and the M-type fiber has better amplification performance than conventional fibers by reducing the signal mode overlap with the doped region. The experiment results show that the M-type 4-core erbium-doped fiber has a gain improvement of 2.8 dB compared with conventional 4-core fiber. The pump conversion efficiency (PCE) has been enhanced from 4.47% to 8.01%. For a 7.0 W pump power at 976 nm, the M-type fiber exhibits an average gain of 20.0 dB and an average noise fiber of 6.8 dB at the L-band. The core-to-core gain variation is less than 1.6 dB.

High-efficiency cladding-pumped Er/Yb co-doped alumino-phosphosilicate fiber for an extended L-band amplification.

Extending the gain bandwidth of L-band optical fiber amplifier has provoked a widespread interest. To date, achieving a high-efficiency extended L-band amplification remains a challenge. Here, we report a cladding-pumped Er/Yb co-doped alumino-phosphosilicate fiber, prepared by the modified chemical vapor deposition process. We demonstrate the efficiency of alumino-phosphosilicate glass for cladding-pumped Er/Yb co-doped fiber, with a gain per unit fiber length of 0.45 dB/m at 1625 nm and a gain ripple of ∼9.4 dB. For 0.8 W pump power, the fiber exhibits a 20 dB gain bandwidth covering 1575-1625 nm and 6.9 dB noise figure at 1625 nm. Additionally, the utilization of multi-mode laser diode enables further significant power savings and cost reduction. To the best of our knowledge, Er/Yb co-doped fiber in alumino-phosphosilicate glass is first proposed, with a cladding-pumped scheme for enhancing an extended L-band performance.

High bismuth-doped germanosilicate fiber for efficient E + S-band amplification.

Bismuth-doped germanosilicate fiber (BGSF), the active media of fiber amplifiers, has attracted widespread attention. Here, we report a BGSF with a high bismuth concentration of 0.075 wt. % and achieve high-efficiency E + S-band amplification, which was prepared by the modified chemical vapor deposition (MCVD) process. The small signal absorption (SSA) and unsaturated loss (UL) of BGSF at 1310 nm are 1.32 and 0.11 dB/m, respectively. The results show a record with only 45 m BGSF was created, to the best of our knowledge, which provides a maximum gain of 39.24 dB with an NF of 6.2 dB at 1430 nm under -20 dBm input signal power.

3 × 1 fiber signal combiner with high beam quality Gaussian-like beam for a 10kW-level fiber laser.

We present the design and fabrication of a 3 × 1 signal combiner with high beam quality based on supermode theory. For improving beam quality, the fiber with core diameter of 34 µm and numerical aperture of 0.11 is first chosen as the output fiber. An 8.89 kW output laser with a power transmission efficiency of 97.2% and a low temperature rise coefficient of 3.5 °C/ kW at >8 kW is obtained when the combiner launched by three Yb-doped fiber lasers. In addition, the energy density distribution of the output beam is Gaussian-like and M2 factor is 2.32, which is the best beam quality compared with the presented signal combiners for high power laser to the best of our knowledge.

Extended L-band 4-Core Er/Yb co-doped fiber amplifier based on 1018†nm cladding pumping.

The extended L-band 4-core Er/Yb co-doped fiber and amplifier (MC-EYDFA) is first proposed and demonstrated, to the best of our knowledge, for space division multiplexing combined with wavelength division multiplexing application. The fiber core co-doped with Er/Yb/P is adopted for bandwidth expansion, and the long wavelength extends to 1625 nm. Numerical simulations further show that efficient amplification and higher saturation power are achieved with the 1018 nm cladding pumping. Based on the integrated 4-core fiber amplifier, an average gain of ∼22 dB covering 1575-1625 nm is experimentally obtained with a 4 W pump power and a 3 dBm total signal power, and the max core-dependent gain (CDG) variation is measured to be 1.7 dB.

4.6†kW linearly polarized and narrow-linewidth monolithic fiber amplifier based on a fiber oscillator laser seed.

In this work, a record output power of 4.6 kW linearly polarized and narrow-linewidth fiber amplifier based on an optimized fiber oscillator laser (FOL) seed was realized by employing a homemade polarization-maintaining Yb-doped fiber (PMYDF), corresponding to a slope efficiency of 79.5% and a 3 dB linewidth of 0.3452 nm. Through an effective strategy relying on decreasing the transmission fiber length from 200 m to 120 m and adding a chirped and tilted fiber Bragg grating (CTFBG), the stimulated Raman scattering (SRS) effects were well-suppressed. By applying the forward combiner with the interconnection between the pump arms into the MOPA system, the MI threshold is increased by more than 560 W and the slope efficiency of the upgraded MOPA system is boosted by 5%. During the experimental process of power amplification, the polarization extinction ratio (PER) remains higher than 15 dB, and a near-diffraction-limited output beam at the laser power of 2980 W was measured with the M2x = 1.314 and M2y = 1.311.

Er/Yb co-doped 345-W all-fiber laser at 1535 nm using hybrid fiber.

The 1.5-µm fiber laser is widely used in the fields of laser lidar, remote sensing, and gas monitoring because of its advantages of being eye-safe and exhibiting low atmospheric transmission loss. However, due to the ∼1-µm amplified spontaneous emission (ASE) of the Er/Yb co-doped fiber (EYDF), it is difficult to improve the laser power. Here, we simulated the effect of the Er3+ concentration and the seed power on ∼1-µm ASE, and fabricated a large mode area EYDF by the modified chemical vapor deposition process. Additionally, a piece of ytterbium-doped fiber was introduced into the master oscillator power amplifier (MOPA) configuration to absorb the generated ∼1-µm ASE simultaneously. Experimental results show that an output power of 345 W with a slope efficiency of 43% at 1535 nm is obtained in an all-fiber configuration, profiting from effective suppression of ∼ 1-µm ASE. To the best of our knowledge, this is the highest output power available with an Er/Yb co-doped fiber from an all-fiber MOPA configuration.

Low-numerical aperture confined-doped long-tapered Yb-doped silica fiber for a single-mode high-power fiber amplifier.

A low-numerical aperture (NA) confined-doped long-tapered (LCT) Yb-doped fiber is proposed and fabricated by modified chemical vapor deposition combined with solution doping technique. The LCT fiber owns the core NA of ∼0.05 and the gain dopant doping diameter ratio of ∼77%, with a core/cladding diameter of 25/400 µm at both ends and 37.5/600 µm in the middle. The laser performance is demonstrated by a bidirectional pumping all-fiber amplifier, of which a 4.18-kW single-mode (M2 factor ∼1.3) laser output is achieved with a slope efficiency of ∼82.8%. Compared with the conventional fiber, the co-pumped and counter-pumped transverse mode instability thresholds and beam quality of the LCT fiber are remarkably enhanced. Throughout the continuous operation, the LCT fiber amplifier presents high power stability with fluctuation of < 1%. These results indicate that LCT fiber has great potential in power scaling remaining excellent beam quality.

High-efficiency cladding-pumped 4-core erbium-doped fiber with a pedestal for space division multiplexing amplification.

A cladding-pumped 4-core erbium-doped fiber (4C-EDF) with a pedestal structure has been firstly, to the best of our knowledge, proposed and fabricated for space division multiplexing (SDM) amplification. The numerical simulation shows that the index-raised pedestal around the fiber core can improve power conversion efficiency (PCE) by enhancing pump power usage. Compared with conventional 4C-EDF, the 4C-EDF with a pedestal has a gain improvement of 4.5 dB and a PCE enhancement of 91.8%, according to the experimental results (pedestal fiber: 9.55%, conventional fiber: 4.98%). For a 6 dBm total input signal power at L-band and a 7.8 W pump power at 976 nm, the pedestal 4C-EDF shows an average gain of 25 dB and an average noise figure (NF) of 6.5 dB over all cores in the wavelength range of 1570.41 nm to 1610.87 nm. The core-to-core gain variation is less than 2 dB.

Extended L-band few-mode Er/Yb Co-doped fiber amplifier with a cladding-pumped pseudo-two-stage configuration.

Spatial division multiplexing (SDM) is one of the most important technologies that may help to solve the future capacity crisis. However, to date, SDM optical amplification is still a challenge for its application. Herein, we numerically and experimentally demonstrated a few-mode Er/Yb co-doped fiber amplifier (FM-EYDFA) for extended L-band operation. A double cladding Er/Yb co-doped fiber was fabricated to expand the L-band bandwidth and a novel, to the best of our knowledge, cladding-pumped pseudo-two-stage amplification configuration was proposed to enhance the L-band gain. With an initial signal power of -16.8 dBm and an injected pump power of 8.8 W at 940 nm, the 20-dB gain range was covered to 1620 nm for two-mode groups of LP01 and LP11. Importantly, the average gain of 25 dB and average differential modal gain (DMG) of <1 dB were obtained in the wavelength range of 1570-1620 nm for all modes. Our results suggest that the cladding-pumped pseudo-two-stage amplifier based on Er/Yb co-doped fiber providing low DMG, and broad bandwidth has a great potential for increasing the future SDM capacity.

Extending the L-band amplification to 1623 nm using Er/Yb/P co-doped phosphosilicate fiber.

The gain bandwidth of the erbium-doped fiber amplifier limits the enhancement of the transmission capacity in optical fiber communication systems. This Letter reports an erbium-ytterbium co-doped phosphosilicate fiber, which is expected to increase transmission capacity by extending the L-band gain bandwidth to 1623 nm. The fiber was fabricated by modified chemical vapor deposition combined with solution doping technology. The mechanism of bandwidth-expansion by inhibiting the signal excited-state absorption was investigated. When the signal power and pump power were maintained at -3.7dBm and ∼720mW at 1480 nm, the 20 dB gain range was extended out to 1623 nm. Additionally, the noise figure at 1623 nm decreased to 6.01 dB, with 23 dBm saturated output power. The results show that the erbium-ytterbium co-doped phosphosilicate fiber has a great potential for extending L-band amplification.

Thermal bleaching of photodarkening and heat-induced loss and spectral broadening in Tm3+-doped fibers.

We demonstrate the thermal bleaching effect on a photodarkened thulium-doped fiber (TDF) in detail. The bleaching effect on visible transmission initiates at 250 °C and a complete recovery is achieved at 550 °C. Prior to the recovery, a post-irradiation heat-induced spectral loss is observed. It indicates that an intermediate energy state is generated in the TDF under exposure to near-infrared (NIR) radiation, exhibiting the spectral attenuation in visible (VIS) and NIR region as driven by color center after thermal activation. And, with thermal treatment, the bleached TDF shows a partial photodarkening (PD) resistance when it is subject to photoirradiation again. In addition, the temperature-dependent spectral broadening and red shift that may distort the measured decay curve of excess loss is observed and discussed.

Promotion of pulse peak power by halving the repetition rate based on a vector soliton.

We report on an all-fiber mode-locked repetition-rate-switch pulse operation in a Yb-doped fiber laser based on a polarization rotation vector soliton. The polarization controller (PC) in a fiber loop and a polarization-dependent isolator at the output port are incorporated into the laser resonator at the switch of the repetition rate. By adjusting the PC in the cavity, the mode locking can be switched between the fundamental repetition rate and half of it with a tiny pulse width change. Also, the halved pulse exhibits unique properties: a huge promotion in energy and peak power. To the best of our knowledge, this is the first all-fiber seed source with a passive switch of the repetition rate based on a vector soliton.

Bleaching of photodarkening in Tm-doped silica fiber with deuterium loading.

We demonstrate the rapid photodarkening (PD) phenomenon in Tm-doped fiber (TDF) core pumped by a laser at 1080 nm and the bleaching effect of deuterium (${{\rm D}_2}$D2) on PD TDF. By ${{\rm D}_2}$D2 loading for seven days, the PD-induced excess loss (PIEL) in the visible (VIS) and near-infrared (NIR) region have been largely eliminated, and no degradation was observed within 30 days. PD resistance of the ${{\rm D}_2}$D2 pretreated TDF has been investigated as well. The formation of color centers based on defects and precursors in the silica matrix and the mechanism of ${{\rm D}_2}$D2 bleaching are discussed.

Yb3+ doped gain guided index anti-guided fiber based on the nanoporous silica glass rod.

We report a heavily Yb3+/Al3+/B3+/F- co-doped high silica rod with a negative refractive index relative to pure silica. The high silica rod was fabricated from nanoporous silica rod using glass phase-separation technology. To lower the refractive index, B3+ and F- were simultaneously introduced into the silica rod and the optical properties of the silica rod were investigated. The fiber preform was prepared with the rod-in-tube method by which the Yb3+ doped high silica rod was only used as an active core. The fiber has a core diameter of 80 µm and a cladding diameter of 400 µm. The measurements show that the Yb3+ in the high silica fiber core is 15856 ppm by weight, while the refractive index is 0.0024 lower than that of the inner cladding. The amplification performance of the fiber was investigated. The results indicate that nanoporous silica glass based on the glass phase-separation technology has great potential for gain-guided index anti-guided high silica fiber.

Double negative curvature anti-resonance hollow core fiber.

We report on a double negative curvature anti-resonance hollow core fiber, in which, the cladding is constituted of 6 large tubes and 6 small tubes arranged in a staggered pattern. The simulation shows that the loss of the fiber can reach or even exceed the loss of double-clad negative curvature anti-resonance hollow core fibers in short wavelength band, due to the staggered arrangement of two kind of tubes and the double negative curvature on the core boundary. The best single mode performance with a loss ratio as high as 100,000 between LP11 mode and LP01 mode is obtained due to simultaneously inhibited LP11 modes and LP21 modes in the fiber structure. The reason for loss oscillations in long wavelength band and the fabrication feasibility of proposed fiber are also discussed.

High coupling efficiency technology of large core hollow-core fiber with single mode fiber.

With the research of hollow-core fiber with large core diameter, the coupling efficiency from hollow-core fiber with large core diameter to single-mode fiber is difficult to increase through the traditional technology, we proposed a novel coupling method to improve the coupling efficiency by attaching a pure silica small ball at the front end of single-mode fiber, the coupling efficiency of 50% from hollow-core fiber with a large core diameter of 110 µm to single-mode fiber can be achieved.

Robust Q-switching based on stimulated Brillouin scattering assisted by Fabry-Perot interference.

Q-switching operation based on stimulated Brillouin scattering (SBS) has been developed for decades due to its inexpensive configuration, high pulse energy output, and the potential to be free from wavelength and material limitations. However, unstable and uncontrollable pulse output affected by SBS's stochastic nature hinders its development. In this work, we demonstrated a unique robust SBS-based Q-switched all-fiber laser. Firstly, a numerical model is developed and a general analysis about the robust Q-switching mechanism is presented. Simulation results show that the spectrum modulation effect such as FP interference is efficient for system to realize steady and controllable output. Secondly, we incorporated a Fabry-Perot (FP) interferometer made of two un-contact end faces of fiber connectors into a SBS-based Q-switched system and demonstrated passively robust Q-switching with simpler and cheaper configuration than most reported ones. Under 600 mW pump power, the SNR was measured to be as high as 62.96 dB, which is the highest SNR obtained from SBS-based Q-switched lasers. To our best knowledge, this is the first demonstration of robust SBS-based Q-switching without any external measures.

Numerical investigation of GHz repetition rate fundamentally mode-locked all-fiber lasers.

GHz repetition rate fundamentally mode-locked lasers have attracted great interest for a variety of scientific and practical applications. A passively mode-locked laser in all-fiber format has the advantages of high stability, maintenance-free operation, super compactness, and reliability. In this paper, we present numerical investigation on passive mode-locking of all-fiber lasers operating at repetition rates of 1-20 GHz. Our calculations show that the reflectivity of the output coupler, the small signal gain of the doped fiber, the total net cavity dispersion, and the modulation depth of the saturable absorber are the key parameters for producing stable fundamentally mode-locked pulses at GHz repetition rates in very short all-fiber linear cavities. The instabilities of GHz repetition rate fundamentally mode-locked all-fiber lasers with different parameters were calculated and analyzed. Compared to a regular MHz repetition rate mode-locked all-fiber laser, the pump power range for the mode-locking of a GHz repetition rate all-fiber laser is much larger due to the several orders of magnitude lower accumulated nonlinearity in the fiber cavity. The presented numerical study provides valuable guidance for the design and development of highly stable mode-locked all-fiber lasers operating at GHz repetition rates.

Gain-tailored Yb/Ce codoped aluminosilicate fiber for laser stability improvement at high output power.

A gain-tailored Ge-free Yb/Ce codoped aluminosilicate fiber is fabricated by MCVD combined with solution doping technique. Through regulating the temperature in the tube and designing the solution doping process, the refractive index profile of this fiber is close to a step-index without any center dip. The laser performance of this fiber is proved through contrast experiments with conventional fiber in a kW-level MOPA setup. The gain-tailored fiber amplifier presents a beam quality of M2 ~1.43 at 1.2 kW. Its MI threshold is 1.25 kW, about 1.74 times as much as that of the conventional fiber amplifier. The laser slope efficiency of the gain-tailored fiber amplifier is 86.75%. Stabilized at an output power of 1.1 kW for 15 hours, the MI threshold does not decrease after this long-term operation, demonstrating a strong resistance to photodarkening effect. These results have confirmed that MCVD-fabricated gain-tailored Yb/Ce codoped aluminosilicate fibers have great potential in power scaling and output stability of high-power fiber lasers and amplifiers.