Does it pay to develop a ground source heat pump system? Evidence from China.

The application potential and environmental benefits of ground source heat pump (GSHP) systems have become the focal points of decarbonization in the building sector. Synchronized and scientific analysis of GSHP systems' environmental and economic performance, however, remains lacking. This study analyzes the application prospects of GSHP systems via a life cycle assessment-based life cycle costing method, and considers China's actual status quo. The internal and external annual costs of a GSHP system per square meter are $ 4.05 and $ 1.37, respectively. Electricity generation and steel production are key processes to improve the environmental performance of a GSHP system further. Compared with coal-based heating, a GSHP system can mitigate 65%-95% of the environmental impact and 85% of external costs, except for the metal depletion impact which is 1.5 times higher than that of coal-based heating. In Shandong Province, promoting GSHP systems can substitute up to 69.4% of the district heating area, which implies reductions in fossil depletion, greenhouse gas emissions, human health impact, ecosystem quality impact, and external costs by up to 2.37 × 1010 kg oil eq, 1.08 × 1011 kg CO2 eq, 3.87 × 105 DALY, 1.18 × 103 Species. year, and $ 2.51 × 1010, respectively. In consideration of environmental and economic aspects, a GSHP system can exhibit benefits compared with coal-based heating after 2.34 years of operation. To improve the economic and environmental performance of GSHP systems, a series of recommendations on financial subsidies, renewable energy development, inter-regional power transmission, steel scrap utilization, and hydrogen reduction steelmaking is provided.

Real-Time Measurement of Drilling Fluid Rheological Properties: A Review.

The accurate and frequent measurement of the drilling fluid's rheological properties is essential for proper hydraulic management. It is also important for intelligent drilling, providing drilling fluid data to establish the optimization model of the rate of penetration. Appropriate drilling fluid properties can improve drilling efficiency and prevent accidents. However, the drilling fluid properties are mainly measured in the laboratory. This hinders the real-time optimization of drilling fluid performance and the decision-making process. If the drilling fluid's properties cannot be detected and the decision-making process does not respond in time, the rate of penetration will slow, potentially causing accidents and serious economic losses. Therefore, it is important to measure the drilling fluid's properties for drilling engineering in real time. This paper summarizes the real-time measurement methods for rheological properties. The main methods include the following four types: an online rotational Couette viscometer, pipe viscometer, mathematical and physical model or artificial intelligence model based on a Marsh funnel, and acoustic technology. This paper elaborates on the principle, advantages, limitations, and usage of each method. It prospects the real-time measurement of drilling fluid rheological properties and promotes the development of the real-time measurement of drilling rheological properties.

Effect of Carbon Fiber and Potassium Titanate Whisker on the Mechanical and Impact Tribological Properties of Fe-Based Impregnated Diamond Bit Matrix.

Various contents of carbon fibers (CFs) and potassium titanate whiskers (PTWs) were added to an Fe-based impregnated diamond bit (IDB) matrix to enhance its adaptability to percussive-rotary drilling. A series of mechanical tests were conducted successively to find the effects of the reinforcing materials on the properties of the Fe-based IDB samples. Then, the fracture surfaces of the samples were analyzed via scanning electron microscopy (SEM) and energy-dispersive spectroscopy, and the worn surfaces and abrasive debris of the samples were analyzed using a laser scanning confocal microscope and SEM. The results show that both the CF and PTW can effectively improve the hardness and bending strength of an Fe-based IDB matrix, and those parameters reached their maximum values at the additive amount of 1 wt%. However, the CF had a better enhancement effect than the PTW. Furthermore, the CF improved the impact wear resistance of the IDB matrix, with a minimum wear rate of 2.38 g/min at the additive amount of 2 wt%. However, the PTW continuously weakened the impact wear resistance of the IDB matrix with increases in its content. Moreover, the morphologies of the worn surfaces indicated that the minimum roughness of the CF-reinforced IDB matrix decreased significantly to as low as 4.91 µm, which was 46.16% lower than that without CF, whereas the minimum roughness of the PTW-reinforced samples decreased by 11.31%. Meanwhile, the abrasive debris of the CF-reinforced samples was more uniform and continuous compared to that of the PTW-reinforced samples. Overall, the appropriate addition of CF or PTWs can enhance the mechanical properties of Fe-based IDB matrices, which can be used on different formations based on their impact wear resistance.

A Zwitterionic Copolymer as Rheology Modifier and Fluid Loss Agents for Water-Based Drilling Fluids.

To overcome the negative impact on the rheological and filtration loss properties of drilling fluids caused by elevated temperature and salts contamination, which are common in ultradeep or geothermal drilling operations, it is imperative to develop highly efficient additives used in the water-based drilling fluid. In this study, a zwitterionic copolymer P (AM/DMC/AMPS/DMAM, ADAD) was synthesized by using acrylamide (AM), cationic monomer methacrylatoethyl trimethyl ammonium chloride (DMC), anionic monomer 2-acrylamide-2-methyl propane sulfonic acid (AMPS), and N,N-dimethylacrylamide (DMAM) through free radical copolymerization. The copolymer was characterized by 1H Nuclear Magnetic Resonance (NMR), Fourier transform infrared spectroscopy (FTIR), elemental analysis, thermogravimetric analysis (TGA), and zeta potential. The rheological behavior, filtration properties, and the performance exposure to salt or calcium contamination in water-based drilling fluid were investigated. The bentonite/polymer suspension showed improved rheological and filtration properties even after aging at 160 °C or a high concentration of salt and calcium. The filtration loss can be greatly reduced by more than 50% (from 18 mL to 7 mL) by the inclusion of 2.0 wt% copolymer, while a slight increase in the filtrate loss was observed even when exposed to electrolyte contamination. Particle size distribution and zeta potential further validate the idea that zwitterionic copolymer can greatly improve the stability of base fluid suspension through positive group enhanced anchoring on the clay surface and repulsion force between negative particles. Moreover, this study can be directed towards the design and application of zwitterionic copolymer in a water-based drilling fluid.