Low-Cost COTS GNSS Interference Monitoring, Detection, and Classification System.

Interference signals cause position errors and outages to global navigation satellite system (GNSS) receivers. However, to solve these problems, the interference source must be detected, classified, its purpose determined, and localized to eliminate it. Several interference monitoring solutions exist, but these are expensive, resulting in fewer nodes that may miss spatially sparse interference signals. This article introduces a low-cost commercial-off-the-shelf (COTS) GNSS interference monitoring, detection, and classification receiver. It employs machine learning (ML) on tailored signal pre-processing of the raw signal samples and GNSS measurements to facilitate a generalized, high-performance architecture that does not require human-in-the-loop (HIL) calibration. Therefore, the low-cost receivers with high performance can justify significantly more receivers being deployed, resulting in a significantly higher probability of intercept (POI). The architecture of the monitoring system is described in detail in this article, including an analysis of the energy consumption and optimization. Controlled interference scenarios demonstrate detection and classification capabilities exceeding conventional approaches. The ML results show that accurate and reliable detection and classification are possible with COTS hardware.

RNN-Aided Human Velocity Estimation from a Single IMU.

Pedestrian Dead Reckoning (PDR) uses inertial measurement units (IMUs) and combines velocity and orientation estimates to determine a position. The estimation of the velocity is still challenging, as the integration of noisy acceleration and angular speed signals over a long period of time causes large drifts. Classic approaches to estimate the velocity optimize for specific applications, sensor positions, and types of movement and require extensive parameter tuning. Our novel hybrid filter combines a convolutional neural network (CNN) and a bidirectional recurrent neural network (BLSTM) (that extract spatial features from the sensor signals and track their temporal relationships) with a linear Kalman filter (LKF) that improves the velocity estimates. Our experiments show the robustness against different movement states and changes in orientation, even in highly dynamic situations. We compare the new architecture with conventional, machine, and deep learning methods and show that from a single non-calibrated IMU, our novel architecture outperforms the state-of-the-art in terms of velocity (≤0.16 m/s) and traveled distance (≤3 m/km). It also generalizes well to different and varying movement speeds and provides accurate and precise velocity estimates.

UWB Channel Impulse Responses for Positioning in Complex Environments: A Detailed Feature Analysis.

Radio signal-based positioning in environments with complex propagation paths is a challenging task for classical positioning methods. For example, in a typical industrial environment, objects such as machines and workpieces cause reflections, diffractions, and absorptions, which are not taken into account by classical lateration methods and may lead to erroneous positions. Only a few data-driven methods developed in recent years can deal with these irregularities in the propagation paths or use them as additional information for positioning. These methods exploit the channel impulse responses (CIR) that are detected by ultra-wideband radio systems for positioning. These CIRs embed the signal properties of the underlying propagation paths that represent the environment. This article describes a feature-based localization approach that exploits machine-learning to derive characteristic information of the CIR signal for positioning. The approach is complete without highly time-synchronized receiver or arrival times. Various features were investigated based on signal propagation models for complex environments. These features were then assessed qualitatively based on their spatial relationship to objects and their contribution to a more accurate position estimation. Three datasets collected in environments of varying degrees of complexity were analyzed. The evaluation of the experiments showed that a clear relationship between the features and the environment indicates that features in complex propagation environments improve positional accuracy. A quantitative assessment of the features was made based on a hierarchical classification of stratified regions within the environment. Classification accuracies of over 90% could be achieved for region sizes of about 0.1 m 2 . An application-driven evaluation was made to distinguish between different screwing processes on a car door based on CIR measures. While in a static environment, even with a single infrastructure tag, nearly error-free classification could be achieved, the accuracy of changes in the environment decreases rapidly. To adapt to changes in the environment, the models were retrained with a small amount of CIR data. This increased performance considerably. The proposed approach results in highly accurate classification, even with a reduced infrastructure of one or two tags, and is easily adaptable to new environments. In addition, the approach does not require calibration or synchronization of the positioning system or the installation of a reference system.

Sick Moves! Motion Parameters as Indicators of Simulator Sickness.

We explore motion parameters, more specifically gait parameters, as an objective indicator to assess simulator sickness in Virtual Reality (VR). We discuss the potential relationships between simulator sickness, immersion, and presence. We used two different camera pose (position and orientation) estimation methods for the evaluation of motion tasks in a large-scale VR environment: a simple model and an optimized model that allows for a more accurate and natural mapping of human senses. Participants performed multiple motion tasks (walking, balancing, running) in three conditions: a physical reality baseline condition, a VR condition with the simple model, and a VR condition with the optimized model. We compared these conditions with regard to the resulting sickness and gait, as well as the perceived presence in the VR conditions. The subjective measures confirmed that the optimized pose estimation model reduces simulator sickness and increases the perceived presence. The results further show that both models affect the gait parameters and simulator sickness, which is why we further investigated a classification approach that deals with non-linear correlation dependencies between gait parameters and simulator sickness. We argue that our approach could be used to assess and predict simulator sickness based on human gait parameters and we provide implications for future research.