The impact of film deposition and annealing on the nanostructure and dielectric constant of organic semiconductor thin films.

The strategy of using a bulk-heterojunction light-absorbing layer has led to the most efficient organic solar cells. However, optimising the blend morphology to maximise light absorption, charge generation and extraction can be challenging. Homojunction devices containing a single component have the potential to overcome the challenges associated with bulk heterojunction films. A strategy towards this goal is to increase the dielectric constant of the organic semiconductor to ≈10, which in principle would lead to free charge carrier generation upon photoexcitation. However, the factors that affect the thin film dielectric constants are still not well understood. In this work we report an organic semiconductor material that can be solution processed or vacuum evaporated to form good quality thin films to explore the effect of chromophore structure and film morphology on the dielectric constant and other optoelectronic properties. 2,2'-[(4,4,4',4'-Tetrakis{2-[2-methoxyethoxy]ethyl}-4H,4'H-{2,2'-bi[cyclo-penta[2,1-b:3,4-b']dithiophene]}-6,6'-diyl)bis(methaneylylidene)]dimalononitrile [D(CPDT-DCV)] was designed to have high electron-affinity end groups and low ionisation-potential central moieties. It can be processed from solution or be thermally evaporated, with the film morphology changing from face-on to a herringbone arrangement upon solvent or thermal annealing. The glycol solubilising groups led to the static dielectric constant (taken from capacitance measurements) of the films to be between 6 and 7 (independent of processing conditions), while the optical frequency dielectric constant depended on the processing conditions. The less ordered solution processed film was found to have the lowest optical frequency dielectric constant of 3.6 at 2.0 × 1014 Hz, which did not change upon annealing. In contrast, the more ordered evaporated film had an optical frequency dielectric constant 20% higher at 4.2 and thermal annealing further increased it to 4.5, which is amongst the highest reported for an organic semiconductor at that frequency. Finally, the more ordered evaporated films had more balanced charge transport, which did not change upon annealing.

Twisted Carbazole Dendrons for Solution-Processable Green Emissive Phosphorescent Dendrimers.

A family of first-generation dendrimers containing 3,5-bis(carbazolyl)phenyl dendrons attached to a green emissive fac-tris(2-phenylpyridyl)iridium(III) core were prepared. The solubility of the dendrimers was imparted by the attachment of tert-butyl surface groups to the carbazole moieties. The dendrimers differed in the number of dendrons attached to each ligand (one or two dendrons) as well as the degree of rotational restriction within the dendrons. The densities of the films containing the doubly dendronized materials were higher than those of their mono-dendronized counterparts, with the dendrimer containing two rotationally constrained dendrons per ligand having the highest density at 1.12 ± 0.04 g cm-3. The dendrimers were found to have high photoluminescence quantum yields (PLQYs) in solution of between 80 and 90%, with the doubly dendronized materials having the lower values and a red-shifted emission. The neat film PLQY values of the dendrimers were less than those measured in solution although the relative decrease was smaller for the doubly dendronized materials. The dendrimers were incorporated into solution-processed bilayer organic light-emitting diodes (OLEDs) composed of neat or blend emissive layers and an electron transport layer. The best-performing devices had the dendrimers blended with a host material and external quantum efficiencies as high as 14.0%, which is higher than previously reported results for carbazole-incorporating emissive dendrimers. A feature of the devices containing blends of the doubly dendronized materials was that the maximum efficiency was relatively insensitive to the concentration in the host between 1 and 7 mol %.

Photomultiplication photodetectors with P3HT:fullerene-free material as the active layers exhibiting a broad response.

A series of polymer photodetectors (PPDs) are fabricated based on P3HT as an electron donor and fullerene-free material DC-IDT2T as an electron acceptor. The only difference among these PPDs is the P3HT:DC-IDT2T doping weight ratios from 2 : 1 to 150 : 1. The PPDs with P3HT:DC-IDT2T (100 : 1, w/w) as the active layers exhibit champion external quantum efficiency (EQE) of 28 000% and 4000% corresponding to 390 nm and 750 nm light illumination at -20 V bias, respectively. The photomultiplication (PM) phenomenon should be attributed to the enhanced hole tunneling injection due to the interfacial band bending, which is induced by the trapped electrons in DC-IDT2T near the Al cathode. The high EQE value in the long wavelength range is due to the effect of DC-IDT2T photon harvesting and exciton dissociation on the interfacial trap-assisted hole tunneling injection. Meanwhile, the PPDs with DC-IDT2T as the electron acceptor exhibit superior stability compared with the PPDs with PC71BM as the electron acceptor.

Improved Performance of Photomultiplication Polymer Photodetectors by Adjustment of P3HT Molecular Arrangement.

A series of photomultiplication (PM)-type polymer photodetectors (PPDs) were fabricated with polymer poly(3-hexylthiophene)-[6,6]-phenyl-C71-butyric acid methyl ester (P3HT-PC71BM) (100:1, w/w) as the active layers, the only difference being the self-assembly time of the active layers for adjusting the P3HT molecular arrangement. The grazing incidence X-ray diffraction (GIXRD) results exhibit that P3HT molecular arrangement can be adjusted between face-on and edge-on structures by controlling the self-assembly time. The champion EQE value of PPDs, based on the active layers without the self-assembly process, arrives at 6380% under 610 nm light illumination at -10 V bias, corresponding to the face-on molecular arrangement of P3HT in the active layers. The EQE values of PPDs were markedly decreased to 1600%, along with the self-assembly time up to 12 min, which should be attributed to the variation of absorption and hole transport ability of the active layers induced by the change of P3HT molecular arrangement. This finding provides an effective strategy for improving the performance of PM-type PPDs by adjusting the molecular arrangement, in addition to the enhanced trap-assisted charge-carrier tunneling injection.