Synthesis of PDMS-b-POEGMA Diblock Copolymers and Their Application for the Thermoresponsive Stabilization of Water-Supercritical Carbon Dioxide Emulsions.

In this study, PDMS13-b-POEGMAx diblock copolymers consisting of a CO2-philic poly(dimethylsiloxane) (PDMS) block connected to a thermosensitive hydrophilic poly(oligoethylene glycol methacrylate) (POEGMA) block were synthesized by reversible addition-fragmentation chain-transfer (RAFT) radical polymerization. Their ability to decrease the water-supercritical CO2 (scCO2) interfacial tension (γ) and to stabilize water-scCO2 emulsions was investigated using an original homemade device developed in the laboratory. This device is able to control the pressure from 1 to 250 bar and the temperature from 40 to 80 °C. It was implemented with 2 visualization windows, a drop tensiometer and a remote optical head for dynamic light scattering (DLS) measurements. These experiments revealed that PDMS-b-POEGMA decreased γ down to 1-2 mN/m and was the most efficient at high pressure (250 bar) and low temperature (40 °C) where PDMS and POEGMA blocks exhibited the highest affinity for their respective phase. The diblock copolymers were shown to stabilize water-scCO2 emulsions. Moreover, the thermosensitive behavior of the POEGMA block in water (with a lower critical solubility temperature around 65 °C) resulted in the formation of temperature-responsive emulsions that could reversibly switch at 100 bar from stable at 40 °C to unstable at 80 °C. These results were rationalized based on the solubility of each individual block of the copolymers in water and scCO2 as a function of temperature and pressure.

Evidence of residual micellar structures in a lipid nanocapsule dispersion. A multi-technique approach.

Nanoemulsions are metastable emulsions in the nanometric range which can be obtained using low-energy processes. A decade ago, it was demonstrated that a non-negligible amount of residual surfactant micelles may coexist with the oil nanodroplets in a model oil/surfactant system. Those micelles were called "wasted" micelles as they did not participate in the formation of the nanodroplets. Little attention has been focused on the potential presence or effect of such secondary structures in nanoemulsions used as drug delivery systems. Here, we present an extensive characterization of lipid nanocapsules, a nanoemulsion obtained from a medium-chain triglyceride mixed with a pegylated surfactant by a process comprising a temperature-dependent phase inversion followed by a cold-water quench. Lipid nanocapsules demonstrate a very good shelf stability. First, for clarity and academic purposes, we briefly present the pros and the cons of the various diffusion-based characterization techniques used i.e., multi-angle and single-angle dynamic light scattering, nanoparticle tracking analysis, fluorescence recovery after photobleaching, and diffusometry nuclear magnetic resonance. Then, combining all these techniques, we show that up to 40 wt% of the surfactant is not involved in the lipid nanocapsule construction but forms residual micellar structures. Those micelles also contain a small quantity of medium-chain triglyceride (2 wt% of the initial amount) and encapsulate around 40 wt% of a fluorescent dye originally dispersed in the oily phase.

NMR diffusometry: A new perspective for nanomedicine exploration.

Nuclear Magnetic Resonance (NMR) based diffusion methods open new perspectives for nanomedicine characterization and their bioenvironment interaction understanding. This review summarizes the theoretical background of diffusion phenomena. Self-diffusion and mutual diffusion coefficient notions are featured. Principles, advantages, drawbacks, and key challenges of NMR diffusometry spectroscopic and imaging methods are presented. This review article also gives an overview of representative applicative works to the nanomedicine field that can contribute to elucidate important issues. Examples of in vitro characterizations such as identification of formulated species, process monitoring, drug release follow-up, nanomedicine interactions with biological barriers are presented as well as possible transpositions for studying in vivo nanomedicine fate.

Galenic Lab-on-a-Chip concept for lipid nanocapsules production.

The continuous production of drug delivery systems assisted by microfluidics has drawn a growing interest because of the high reproducibility, low batch-to-batch variations, narrow and controlled particle size distributions and scale-up ease induced by this kind of processes. Besides, microfluidics offers opportunities for high throughput screening of process parameters and the implementation of process characterization techniques as close to the product as possible. In this context, we propose to spotlight the GALECHIP concept through the development of an instrumented microfluidic pilot considered as a Galenic Lab-on-a-Chip to formulate nanomedicines, such as lipid nanocapsules (LNCs), under controlled process conditions. In this paper we suggest an optimal rational development in terms of chip costs and designs. First, by using two common additive manufacturing techniques, namely fused deposition modelling and multi-jet modelling to prototype customized 3D microfluidic devices (chips and connectors). Secondly, by manufacturing transparent Silicon (Si)/Glass chips with similar channel geometries but obtained by a new approach of deep reactive ion etching (DRIE) technology suitable with in situ small angle X-ray scattering characterizations. LNCs were successfully produced by a phase inversion composition (PIC) process with highly monodispersed sizes from 25 nm to 100 nm and formulated using chips manufactured by 3D printing and DRIE technologies. The transparent Si/Glass chip was also used for the small angle X-ray scattering (SAXS) analysis of the LNC formulation with the PIC process. The 3D printing and DRIE technologies and their respective advantages are discussed in terms of cost, easiness to deploy and process developments in a GALECHIP point of view.

Correction: Galenic lab-on-a-chip concept for lipid nanocapsules production.

Correction for 'Galenic Lab-on-a-Chip concept for lipid nanocapsules production' by Nicolas Rolley et al., Nanoscale, 2021, 13, 11899-11912, DOI: 10.1039/D1NR00879J.

Modulation of protein release from penta-block copolymer microspheres.

Releasing a protein according to a zero-order profile without protein denaturation during the polymeric microparticle degradation process is very challenging. The aim of the current study was to develop protein-loaded microspheres with new PLGA based penta-block copolymers for a linear sustained protein release. Lysozyme was chosen as model protein and 40 µm microspheres were prepared using the solid-in-oil-in-water solvent extraction/evaporation process. Two types of PLGA-P188-PLGA penta-block copolymers were synthetized with two PLGA-segments molecular weight (20 kDa or 40 kDa). The resulting microspheres (50P20-MS and 50P40-MS) had the same size, an encapsulation efficiency around 50-60% but different porosities. Their protein release profiles were complementary: linear but non complete for 50P40-MS, non linear but complete for 50P20-MS. Two strategies, polymer blending and microsphere mixing, were considered to match the release to the desired profile. The (1:1) microsphere mixture was successful. It induced a bi-phasic release with a moderate initial burst (around 13%) followed by a nearly complete linear release for 8 weeks. This study highlighted the potential of this penta-block polymer where the PEO block mass ratio influence clearly the Tg and consequently the microsphere structure and the release behavior at 37 °C. The (1:1) mixture was a starting point but could be finely tuned to control the protein release.

Crystallization and dynamical arrest of attractive hard spheres.

Crystallization of hard spheres interacting with a square well potential was investigated by numerical simulations using so-called Brownian cluster dynamics. The phase diagram was determined over a broad range of volume fractions. The crystallization rate was studied as a function of the interaction strength expressed in terms of the second virial coefficient. For volume fractions below about 0.3 the rate was found to increase abruptly with increasing attraction at the binodal of the metastable liquid-liquid phase separation. The rate increased until a maximum was reached after which it decreased with a power law dependence on the second virial coefficient. Above a critical percolation concentration, a transient system spanning network of connected particles was formed. Crystals were formed initially as part of the network, but eventually crystallization led to the breakup of the network. The lifetime of the transient gels increased very rapidly over a small range of interaction energies. Weak attraction destabilized the so-called repulsive crystals formed in pure hard sphere systems and shifted the coexistence line to higher volume fractions. Stronger attraction led to the formation of a denser, so-called attractive, crystalline phase. Nucleation of attractive crystals in the repulsive crystalline phase was observed close to the transition.

Importance of Combining Advanced Particle Size Analysis Techniques To Characterize Cell-Penetrating Peptide-Ferrocifen Self-Assemblies.

The design of a simple platform to target the delivery of notably hydrophobic drugs into cancer cells is an ultimate goal. Here, three strategies were combined in the same nanovector, in limiting the use of excipients: cell-penetrating peptides, an amphiphilic prodrug, and self-assembly. Light scattering and cryogenic transmission electron microscopy revealed one size population of objects around 100 nm with a narrow size distribution. However, in-depth analysis of the suspension by nanoparticle tracking analysis, small-angle X-ray scattering, and nuclear magnetic resonance (NMR) diffusometry demonstrated the presence of another population of small objects (<2 nm). It has been shown that these small self-assemblies represented >99% of the matter! This presence was clearly and unambiguously demonstrated by NMR diffusometry experiments. The study highlights the importance and the complementary contribution of each characterization method to reflect the reality of the studied nanoassembly.

Tracer diffusion in colloidal gels.

Computer simulations were done of the mean square displacement (MSD) of tracer particles in colloidal gels formed by diffusion or reaction limited aggregation of hard spheres. The diffusion coefficient was found to be determined by the volume fraction accessible to the spherical tracers (phi a) independent of the gel structure or the tracer size. In all cases, critical slowing down was observed at phi a approximately 0.03 and was characterized by the same scaling laws reported earlier for tracer diffusion in a Lorentz gas. Strong heterogeneity of the MSD was observed at small phi a and was related to the size distribution of pores.

The influence of bond rigidity and cluster diffusion on the self-diffusion of hard spheres with square well interaction.

Hard spheres interacting through a square well potential were simulated by using two different methods: Brownian cluster dynamics (BCD) and event driven Brownian dynamics (EDBD). The structure of the equilibrium states obtained by both methods was compared and found to be almost identical. Self-diffusion coefficients (D) were determined as a function of the interaction strength. The same values were found by using BCD or EDBD. Contrary to EDBD, BCD allows one to study the effect of bond rigidity and hydrodynamic interaction within the clusters. When the bonds are flexible, the effect of attraction on D is relatively weak compared to systems with rigid bonds. D increases first with increasing attraction strength, and then decreases for stronger interaction. Introducing intracluster hydrodynamic interaction weakly increases D for a given interaction strength. Introducing bond rigidity causes a strong decrease in D which no longer shows a maximum as function of the attraction strength.

NMR diffusometry data sampling optimization for mixture analysis.

NMR diffusometry is a powerful but challenging method to analyze complex mixture. Each component diffuses differently, from the faster small species to the slower large species, corresponding to different signal attenuation. However, the method is highly sensitive to the quality of the acquired data and the performance of the processing used to resolve multiexponential signals influences. Adapting the signal decay sampling to the mixture composition is one way to improve the precision of the measure. In this work, we propose a prediction tool, based on the calculation of the Cramér-Rao lower bound to minimize the variance of diffusion coefficient estimation in order to determine the optimal number of diffusion gradient steps, the best diffusion gradient sampling (among linear, exponential, quadratic and sigmoidal ones) and the optimal maximum diffusion factor. The tool was validated experimentally on a unimer/micelle solution of sodium dodecyl sulfate and on Caelyx®, a commercial liposomal preparation containing a mixture of pegylated-liposomes and sucrose.

A multi-scale approach for percolation transition and its application to cement setting.

Shortly after mixing cement grains with water, a cementitious fluid paste is formed that immediately transforms into a solid form by a phenomenon known as setting. Setting actually corresponds to the percolation of emergent network structures consisting of dissolving cement grains glued together by nanoscale hydration products, mainly calcium-silicate-hydrates. As happens in many percolation phenomena problems, the theoretical identification of the percolation threshold (i.e. the cement setting) is still challenging, since the length scale where percolation becomes apparent (typically the length of the cement grains, microns) is many times larger than the nanoscale hydrates forming the growing spanning network. Up to now, the long-lasting gap of knowledge on the establishment of a seamless handshake between both scales has been an unsurmountable obstacle for the development of a predictive theory of setting. Herein we present a true multi-scale model which concurrently provides information at the scale of cement grains (microns) and at the scale of the nano-hydrates that emerge during cement hydration. A key feature of the model is the recognition of cement setting as an off-lattice bond percolation process between cement grains. Inasmuch as this is so, the macroscopic probability of forming bonds between cement grains can be statistically analysed in smaller local observation windows containing fewer cement grains, where the nucleation and growth of the nano-hydrates can be explicitly described using a kinetic Monte Carlo Nucleation and Growth model. The most striking result of the model is the finding that only a few links (~12%) between cement grains are needed to reach setting. This directly unveils the importance of explicitly including nano-texture on the description of setting and explains why so low amount of nano-hydrates is needed for forming a spanning network. From the simulations, it becomes evident that this low amount is least affected by processing variables like the water-to-cement ratio and the presence of large quantities of nonreactive fillers. These counter-intuitive predictions were verified by ex-professo experiments that we have carried out to check the validity of our model.

Lipid nanocapsules maintain full integrity after crossing a human intestinal epithelium model.

Lipid nanocapsules (LNCs) have demonstrated great potential for the oral delivery of drugs having very limited oral bioavailability (BCS class II, III and IV molecules). It has been shown previously that orally-administered LNCs can permeate through mucus, increase drug absorption by the epithelial tissue, and finally, increase drug bioavailability. However, even if transport mechanisms through mucus and the intestinal barrier have already been clarified, the preservation of particle integrity is still not known. The aim of the present work is to study in vitro the fate of LNCs after their transportation across an intestinal epithelium model (Caco-2 cell model). For this, two complementary techniques were employed: Förster Resonance Energy Transfer (FRET) and Nanoparticle Tracking Analysis (NTA). Results showed, after 2h, the presence of nanoparticles in the basolateral side of the cell layer and a measurable FRET signal. This provides very good evidence for the transcellular intact crossing of the nanocarriers.

How to design the surface of peptide-loaded nanoparticles for efficient oral bioavailability?

The oral administration of proteins is a current challenge to be faced in the field of therapeutics. There is currently much interest in nanocarriers since they can enhance oral bioavailability. For lack of a clear definition, the key characteristics of nanoparticles have been highlighted. Specific surface area is one of these characteristics and represents a huge source of energy that can be used to control the biological fate of the carrier. The review discusses nanocarrier stability, mucus interaction and absorption through the intestinal epithelium. The protein corona, which has raised interest over the last decade, is also discussed. The universal ideal surface is a myth and over-coated carriers are not a solution either. Besides, common excipients can be useful on several targets. The suitable design should rather take into account the composition, structure and behavior of unmodified nanomaterials.

Relation between aggregation and phase separation: three-dimensional Monte Carlo simulations.

We study phase separation of particles in solution using Monte Carlo simulations of reversible aggregation on a cubic lattice. Two stages of the phase separation can be clearly distinguished: initial random aggregation and subsequent densification. Step one leads to a distribution of fractal aggregates close to the binodal and to a temporary gel for large attractive interaction. Step two leads to isolated spherical dense domains close to the binodal and branched wormlike strands for large attractive interactions. The transition between the two types of structure is gradual and there is no clear feature that shows the existence of a spinodal. The first stage of the phase separation is metastable very close to the binodal or at very large interaction energy. In the latter case, the second step can be viewed as an aging process of the gel formed in the first step.

Fate of paclitaxel lipid nanocapsules in intestinal mucus in view of their oral delivery.

The bioavailability of paclitaxel (Ptx) has previously been improved via its encapsulation in lipid nanocapsules (LNCs). In this work, the interactions between LNCs and intestinal mucus are studied because they are viewed as an important barrier to successful oral delivery. The rheological properties of different batches of pig intestinal mucus were studied under different conditions (the effect of hydration and the presence of LNCs). Fluorescence resonance energy transfer (FRET) was used to study the stability of LNCs in mucus at 37°C for at least 3 hours. Diffusion through 223, 446, and 893 µm mucus layers of 8.4, 16.8, and 42 µg/mL Ptx formulated as Taxol® (Bristol-Myers Squibb, Rueil-Malmaison, France) or encapsulated in LNCs (Ptx-LNCs) were investigated. The effect of the size of the LNCs on their diffusion was also investigated (range, 25-110 nm in diameter). Mucus behaves as a non-Newtonian gel with rheofluidifying properties and a flow threshold. The viscous (G″) and elastic (G') moduli and flow threshold of the two mucus batches varied with water content, but G' remained below G″. LNCs had no effect on mucus viscosity and flow threshold. The FRET efficiency remained at 78% after 3 hours. Because the destruction of the LNCs would lead to a FRET efficiency below 25%, these results suggest only a slight modification of LNCs after their contact with mucus. The diffusion of Taxol® and Ptx-LNCs in mucus decreases if the mucus layer is thicker. Interestingly, the apparent permeability across mucus is higher for Ptx-LNCs than for Taxol® for drug concentrations of 16.8 and 42 µg/mL Ptx (P<0.05). The diffusion of Ptx-LNCs through mucus is not size-dependent. This study shows that LNCs are stable in mucus, do not change mucus rheological properties, and improve Ptx diffusion at low concentrations, thus making these systems good candidates for Ptx oral delivery. The study of the physicochemical interaction between the LNC surface and its diffusion in mucus is now envisioned.

Self-diffusion of non-interacting hard spheres in particle gels.

Different kinds of particle gels were simulated using a process of random aggregation of hard spheres. The mean square displacement of Brownian spherical tracer particles through these rigid gels was monitored and the average diffusion coefficient, normalized with the free diffusion coefficient (D), was obtained. For each gel structure the effect of the gel volume fraction (φ) and size ratio of the tracer (d) on the relative diffusion coefficient was investigated systematically. The volume fraction that is accessible to the tracers (φ(a)) was determined in each case. D was found to be approximately the same if φ(a) was the same, independent of φ, d and the gel structure. However a different behaviour is found if the tracers can penetrate the strands of the gel. A state diagram of d versus φ is given that shows the critical values (d(c), φ(c)) at which all tracers become trapped. Different values are found for different gel structures. The dependence of D on φ/φ(c) is independent of d, while the dependence of D on d/d(c) is independent of φ.

Self-diffusion of reversibly aggregating spheres.

Reversible diffusion limited cluster aggregation of hard spheres with rigid bonds was simulated and the self-diffusion coefficient was determined for equilibrated systems. The effect of increasing attraction strength was determined for systems at different volume fractions and different interaction ranges. It was found that the slowing down of the diffusion coefficient due to crowding is decoupled from that due to cluster formation. The diffusion coefficient could be calculated from the cluster size distribution and became zero only at infinite attraction strength when permanent gels are formed. It is concluded that so-called attractive glasses are not formed at finite interaction strength.

Phase separation and percolation of reversibly aggregating spheres with a square-well attraction potential.

Reversible aggregation of spheres is simulated using a novel method in which clusters of bound spheres diffuse collectively with a diffusion coefficient proportional to their radius. It is shown that the equilibrium state is the same as with other simulation techniques, but with the present method more realistic kinetics are obtained. The behavior as a function of volume fraction and interaction strength was tested for two different attraction ranges. The binodal and the percolation threshold were determined. The cluster structure and size distribution close to the percolation threshold were found to be consistent with the percolation model. Close to the binodal phase separation occurred through the growth of spherical dense domains, while for deep quenches a system spanning network is formed that coarsens with a rate that decreases with increasing attraction. We found no indication for arrest of the coarsening.