The effects of a revised operational dose quantity on the response characteristics of neutron survey instruments.

The ICRU is considering revising the definition of ambient dose equivalent. This paper investigates the impacts of the proposed change on four designs of neutron survey instrument, the GNU, HSREM, LB6411 and Studsvik 2202D, in terms of their respective energy dependences of response and their performances in realistic workplace fields. In some circumstances the current designs of instrument still produce acceptable characteristics, but in general they may need to be re-optimized to better match the requirements of the new operational quantity; to that end, a simple retrofit solution for the GNU is demonstrated. The performance criteria against which instruments are judged may also need to be revised to reflect the proposed change.

The MCNP-4C2 design of a two element photon/electron dosemeter that uses magnesium/copper/phosphorus doped lithium fluoride.

The Health Protection Agency is changing from using detectors made from 7LiF:Mg,Ti in its photon/electron personal dosemeters, to 7LiF:Mg,Cu,P. Specifically, the Harshaw TLD-700H card is to be adopted. As a consequence of this change, the dosemeter holder is also being modified not only to accommodate the shape of the new card, but also to optimize the photon and electron response characteristics of the device. This redesign process was achieved using MCNP-4C2 and the kerma approximation, electron range/energy tables with additional electron transport calculations, and experimental validation, with different potential filters compared; the optimum filter studied was a polytetrafluoroethylene disc of diameter 18 mm and thickness 4.3 mm. Calculated relative response characteristics at different angles of incidence and energies between 16 and 6174 keV are presented for this new dosemeter configuration and compared with measured type-test results. A new estimate for the energy-dependent relative light conversion efficiency appropriate to the 7LiF:Mg,Cu,P was also derived for determining the correct dosemeter response.

THE RESPONSE OF THE PHE NEUTRON PERSONAL DOSEMETER IN TERMS OF THE PROPOSED ICRU PERSONAL DOSE EQUIVALENT.

The ICRU is considering amending the definition of the operational quantity for personnel monitoring. The present work investigates the impact of the proposed change on the PHE neutron personal dosemeter, which utilizes electrochemically etched PADC and is currently optimized in terms of Hp(10). The energy-dependent dose response characteristics of the dosemeter, and its performance in realistic workplace neutron fields, are calculated and compared for both the current and proposed dose quantities, for both frontal and rotationally isotropic fields. Adoption of the proposed quantity would make the dosemeter more sensitive to normally incident neutrons, but it would require some modification to ensure that it is able to meet the recommendations of the current ISO standard at all energies and its directional dependence of response would be poorer. The implications of this are discussed.

Improved characterisation of the HPA PADC neutron personal dosemeter.

The fast neutron energy dependence of response of the HPA PADC neutron personal dosemeter has been measured from 144 keV to 19 MeV using monoenergetic neutron fields. Below 144 keV the relative energy and angle dependence of response have been determined using MCNP-4C2. New data from the SIGMA field at Cadarache, France, have been used to determine the appropriate scaling factor for the calculated response to thermal and intermediate energy neutrons. These newly determined response characteristics of the dosemeter are discussed with respect to its performance in the EVIDOS workplace field irradiations.

Neutron area survey instrument measurements in the EVIDOS project.

Neutron survey instruments have been exposed at all the measurement locations used in the EVIDOS project. These results have an important impact in the interpretation of the results from the project, since operationally the survey instrument will be used for an initial assessment of and routine monitoring of the ambient dose equivalent dose rate. Additionally, since the response of these instruments is in some cases very well characterised, their systematic deviations from the reference quantities provide an important verification of the determination of those quantities.

Human colonic sulfomucin identified by a specific monoclonal antibody.

Since the 1960s, the loss of sulfomucin from colonic epithelium has been considered to be an indicator of an early stage of carcinogenesis; yet, the biochemical basis for this phenomenon has never been elucidated. We recently prepared a monoclonal antibody (mAb) 91.9H that immunoprecipitates the normal colonic mucins metabolically incorporating [35S]-sulfate. This mouse IgG1 antibody did not cross-react with colon carcinoma mucins that lack sulfate groups. Using normal colonic epithelia unlabeled or radiolabeled with [35S]sulfate and [3H]glucosamine, we purified a high molecular weight glycoprotein that reacts with mAb 91.9H. This was achieved by a combination of DEAE-cellulose anion-exchange chromatography, consecutive treatments with chondroitinase ABC plus heparitinase and with sodium dodecyl sulfate plus 2-mercaptoethanol, and gel filtration on Sepharose CL-2B in the presence of 8 M urea. Antibody reactivity was found in acidic but not neutral high molecular weight glycoproteins. After Sepharose CL-2B fractionation, the mAb 91.9H-reactive fractions consisted of a component with an approximate molecular weight of 500,000-900,000. A purified sulfomucin contained protein, neutral sugar, amino sugar, sialic acid, and sulfate in an approximate ratio of 2.5:1.0:1.1:0.4:0.5. The polypeptide portion was rich in hydrophilic amino acids, particularly threonine. Binding of mAb 91.9H in solid-phase assays was inhibited to 50% by purified normal colon acidic mucin at doses of 5-50 micrograms/ml, depending on different preparations. Various glycosaminoglycans or sulfatides did not show inhibitory activity. Sulfomucin reactivity with mAb 91.9H, as determined by solid-phase-binding inhibition and by dot blot assays, was significantly reduced by chemical desulfation of sulfomucins with anhydrous hydrochloric acid, suggesting that sulfate groups served as a portion of the immunochemical determinant for this antibody. Sulfate residues were apparently linked to alkaline-sensitive carbohydrate chains, but alkaline-released carbohydrate chains did not react with mAb 91.9H. Immunohistochemical examinations showed that mAb 91.9H bound normal colonic epithelial cells, which also stained with high-iron diamine, more strongly than it bound colon carcinoma cells.

Monoclonal antibody against human colonic sulfomucin: immunochemical detection of its binding sites in colonic mucosa, colorectal primary carcinoma, and metastases.

Previous studies using metabolic labeling of fresh colonic mucosa and colorectal carcinoma with [35S]sulfate followed by biochemical analysis demonstrated that the amount of a sulfated high-molecular-weight glycoprotein expressed in primary colorectal carcinoma was lower than that in normal mucosa, and that the amount further decreased in liver metastases. This suggested that this sulfated molecule represented a sulfomucin previously defined by histochemical reactivity with a cationic dye. We have extracted and partially purified this high-molecular-weight sulfated glycoprotein from normal human colonic mucosa. We immunized mice with the partially purified sulfomucin and generated hybridomas. One cloned hybridoma, designated as 91.9H, produced a monoclonal antibody strongly reactive with a component which migrated at an identical position as the metabolically [35S]sulfate-labeled high-molecular-weight glycoprotein after polyacrylamide gel electrophoresis in the presence of sodium dodecyl sulfate. The reactive molecules appeared to have a polydisperse nature with a molecular weight ranging between 400,000 and 900,000. The [35S]sulfate-labeled high-molecular-weight glycoprotein was bound to Staphylococcus Protein A-agarose coated with this monoclonal antibody but did not bind to unconjugated Protein A-agarose. The immunoprecipitated substance also migrated at an apparent molecular weight range of 400,000 to 900,000. The reactivity of monoclonal antibody 91.9H with the extracts of normal mucosa, colorectal primary carcinoma, and metastasis was compared by dot blot assay on a nitrocellulose membrane. This antibody was more reactive with the extracts of mucosa adjacent to carcinoma tissues than with the carcinoma extracts. Primary tumors showed higher reactivity than metastases in most of the cases. These results strongly suggest that this antibody is specific to colonic sulfomucins or at least to mucins closely related to colonic mucins previously identified by metabolic labeling with [35S]sulfate.

CALIBRATION OF THERMOLUMINESCENCE AND FILM DOSEMETERS FOR SKIN DOSES FROM HIGH-ACTIVITY MICROPARTICLES.

The use of EXT-RAD™ extremity TLDs and radiochromic film to measure doses from primarily beta-emitting microparticles is discussed. Specific calibration techniques have been developed, using both Monte Carlo modelling and experiments. Results for a (90)Sr/(90)Y microparticle are presented to illustrate the general techniques and to demonstrate reasonable agreement between the dosimetry methods.

THE PHE FORTUITOUS DOSIMETRY CAPABILITY BASED ON OPTICALLY STIMULATED LUMINESCENCE OF MOBILE PHONES.

The Public Health England fortuitous dosimetry capability is reviewed, with particular attention focussed on the derivation of its energy and fading corrections, the Monte Carlo techniques used to generate the calibration factors between phone and body doses, and the procedures set in place to facilitate a reliable and effective service.

Modelling of neutron survey instrument performance and experimental validation of those calculated response data.

Three moderator-type neutron survey instruments have been modelled for energy and angle dependence of the response, in greater detail than before. These response data have been verified by comparison with published experimental measurements and measurements made specifically for this project. Influences on the instrument response have also been investigated. These have included its mode-of-use and perturbations caused by variations in the instrument manufacture. The implications of these new response data have been assessed by an extensive programme of folding the responses with workplace energy distributions.

Development of a retrospective/fortuitous accident dosimetry service based on OSL of mobile phones.

Work is presented on the development of a retrospective/fortuitous accident dosimetry service using optically stimulated luminescence of resistors found in mobile phones to determine the doses of radiation to members of the public following a radiological accident or terrorist incident. The system is described and discussed in terms of its likely accuracy in a real incident.

The measurement using passive dosemeters of the neutron component of aircraft crew dose.

The cosmic radiation field at aviation altitudes can be measured with simple passive detectors. The non-neutron component may be measured by means of thermoluminescence dosimetry or other techniques, and the neutron component may be measured using poly allyl diglycol carbonate (PADC) dosemeters as described in this paper. Effective dose from neutron radiation becomes the larger component for altitudes above about 10 km, in general. The dominance is more pronounced for higher latitudes. The neutron energies range up to the maximum of the incident protons, that is many GeV. However the majority of the dose is contributed by neutrons of a few hundred MeV and less, with two maxima in the fluence spectrum, one between 1 and 10 MeV and the other between 50 and 150 MeV. We have used PADC dosemeters, electrochemically etched, to estimate the neutron component of effective dose. Up to 50 dosemeters are used in a single measurement to obtain an estimate of sufficient precision for total neutron effective doses of 50 microSv and less. The neutron fluence response characteristics of the dosemeter have been measured up to 70 MeV. These are extrapolated up to 180 MeV. This extrapolation is validated, partially, by a comparison of measured and predicted readings in the CERN reference field. From the dosemeter readings for exposure on board aircraft, neutron fluence may be estimated assuming an isotropic radiation field and the estimated neutron fluence spectrum. The neutron fluence may then be converted to effective dose using published values of conversion coefficients with the same assumptions of isotropy and known fluence spectrum. For the measurement results reported here, the calculated spectrum for the CERN concrete shielded field is used.

Measurements of the high energy neutron component of cosmic radiation fields in aircraft using etched track dosemeters.

Measurements of the complex cosmic radiation field in aircraft at altitude are made with a passive survey meter comprising routine-use thermoluminescent detectors and etched track detectors. The energy dependence of response of the etched track detectors used to determine the neutron component has been characterized, partly, up to a neutron energy of 180 MeV. The neutron detectors are routinely calibrated in the CERN/EC Reference Field. The 15% determination level for total dose equivalent is 100 microSv. The evidence is that the passive survey meter provides a reliable determination of route dose.

The use of passive personal neutron dosemeters to determine the neutron dose equivalent component of radiation fields in spacecraft.

For the altitude range and inclination of the International Space Station (ISS), secondary neutrons can be a major contributor to dose equivalent inside a spacecraft. The exact proportion is very dependent on the amount of shielding of the primary galactic cosmic radiation and trapped particles, but is likely to lie in the range of 10-50%. Personal neutron dosemeters of simple design, processed using simple techniques developed for personal dosimetry, may be used to estimate this neutron component.

High energy neutron response characteristics of a passive survey instrument for the determination of cosmic radiation fields in aircraft.

A passive survey instrument has been developed for the determination of cosmic radiation fields in aircraft. The instrument contains 30 TLDs and 36 PADC etched track detectors in order to obtain the required precision and an isotropic response. Two active electronic personal dosemeters are included to record the time profile of the field intensity. The instrument is robust and reliable, and is particularly useful to verify values of route doses based on calculations. The energy of the neutron component of the field to be determined extends to over 500 MeV, but with the majority of the dose equivalent below 200 MeV. The results are reported of measurements at Uppsala University and Physikalisch-Technische Bundesanstalt of the response characteristics of the instrument to quasi-monoenergetic neutrons in the energy range 60 to 180 MeV and for monoenergetic neutrons of energy from 70 keV to 14.7 MeV.

Angle dependence of response characteristics of neutron survey instruments.

Neutron area survey instruments are designed to have an approximately isotropic response. In practice, the response cannot be perfectly isotropic for instruments that do not have spherical symmetry, and for all instruments it is modified by the inclusion of batteries, electronics, handles, etc. This affects the ability of the survey instrument to measure accurately an isotropic dose equivalent quantity. Measurements of the angle dependence of response for four of the most commonly used designs of survey instrument (Harwell 0949, Mark 7 NRM, NM2 and Studsvik 2202D) have been performed in a low-scatter room using radionuclide and monoenergetic neutron sources. The Monte Carlo code MCNP has been used to model the responses and to investigate their sensitivity to the polyethylene density, counting gas pressure and other manufacturing tolerances. Preliminary modelling results are presented here.

Practical implications of neutron survey instrument performance.

Improvements have been made to the Monte Carlo modelling used to calculate the response of the neutron survey instruments most commonly used in the UK, for neutron energies up to 20 MeV. The improved modelling of the devices includes the electronics and battery pack, allowing better calculations of both the energy and angle dependence of response. These data are used to calculate the response of the instruments in rotationally and fully isotropic, as well as unidirectional fields. Experimental measurements with radionuclide sources and monoenergetic neutron fields have been, and continue to be made, to test the calculated response characteristics. The enhancements to the calculations have involved simulation of the sensitivity of the response to variations in instrument manufacture, and will include the influence of the user and floor during measurements. The practical implications of the energy and angle dependence of response, variations in manufacture, and the influence of the user are assessed by folding the response characteristics with workplace energy and direction distributions.

Measurements with the new PHE neutron survey instrument.

A novel design of survey instrument has been developed to accurately estimate ambient dose equivalent from neutrons with energies in the range from thermal to 20 MeV. The device features moderating and attenuating layers to ease measurement of fast and intermediate energy neutrons, combined with guides that channel low-energy neutrons to the single, central detector. A prototype of this device has been constructed and exposed to a set of calibration fields: the resulting measured responses are presented and discussed here, and compared against Monte Carlo data. A simple simulated workplace neutron field has also been developed to test the device.

Monte Carlo modelling of 90Sr/90Y and 85Kr beta fields for Hp(3) measurements.

In support of research aimed at developing a thermoluminescence dosemeter capable of accurately measuring ionising radiation doses to the lens of the eye, Monte Carlo modelling of a standard beta exposure set-up has been performed. It was found that electrons with an energy distribution corresponding to the beta emission spectrum from (85)Kr deposit negligible doses at a depth of 3 mm in tissue, but doses from (90)Sr/(90)Y are significant; free in air and fluence-to-Hp(3,θ°) and -Hp(0.07,θ°) conversion coefficient data were found for this field for exposures at 0°, 30° and 60° angles of incidence, and the response characteristics of the new eye dosemeter were evaluated. It was shown that the results were not affected greatly by the shape of the calibration phantom. However, it was demonstrated that the presence of intermediating air and beam flattening filters hardens the energy distribution of the field at the point of test, relative to a raw (90)Sr/(90)Y source, and this impacts dose depositions.

Type testing of a head band dosemeter for measuring eye lens dose in terms of H(P)(3).

A new head band dosemeter, for the measurement of eye lens dose in terms of Hp(3), has been type tested by Public Health England's Centre for Radiation, Environmental and Chemical Hazards [formerly part of the UK Health Protection Agency (HPA)]. The type tests were based on the International Standard ISO 12794, drawing also upon earlier work at HPA. The results show that, unlike many existing dosemeters, the new head band dosemeter correctly measures Hp(3) for beta radiations as well as photons.