Phase Engineering via Aluminum Doping Enhances the Electrochemical Stability of Lithium-Rich Cobalt-Free Layered Oxides for Lithium-Ion Batteries.

Lithium-rich, cobalt-free oxides are promising potential positive electrode materials for lithium-ion batteries because of their high energy density, lower cost, and reduced environmental and ethical concerns. However, their commercial breakthrough is hindered because of their subpar electrochemical stability. This work studies the effect of aluminum doping on Li1.26Ni0.15Mn0.61O2 as a lithium-rich, cobalt-free layered oxide. Al doping suppresses voltage fade and improves the capacity retention from 46% for Li1.26Ni0.15Mn0.61O2 to 67% for Li1.26Ni0.15Mn0.56Al0.05O2 after 250 cycles at 0.2 C. The undoped material has a monoclinic Li2MnO3-type structure with spinel on the particle edges. In contrast, Al-doped materials (Li1.26Ni0.15Mn0.61-xAlxO2) consist of a more stable rhombohedral phase at the particle edges, with a monoclinic phase core. For this core-shell structure, the formation of Mn3+ is suppressed along with the material's decomposition to a disordered spinel, and the amount of the rhombohedral phase content increases during galvanostatic cycling. Whereas previous studies generally provided qualitative insight into the degradation mechanisms during electrochemical cycling, this work provides quantitative information on the stabilizing effect of the rhombohedral shell in the doped sample. As such, this study provides fundamental insight into the mechanisms through which Al doping increases the electrochemical stability of lithium-rich cobalt-free layered oxides.

Altering Mechanical Properties to Improve Electrode Contacts by Organic Modification of Silica-Based Ionogel Electrolytes for Sodium-Ion Batteries.

Sodium-ion batteries (SIBs) are a possible candidate to create safe, sustainable, and cost-effective batteries. Solid sodium-ion conducting organically modified ionogel electrolytes are investigated. Silica-based ionogels typically consist of an ionic liquid electrolyte (ILE) confined within a silica matrix and possess high thermal stability, good ionic conductivity, safety, and good electrochemical stability. However, they readily deteriorate when stress is applied, decreasing the electrolyte's and battery's overall performance. The mechanical characteristics of silica can be improved using organic moieties, creating Ormosils®. Silica-based ionogels with phenyl-modified silanes improve the mechanical characteristics by a reduction of their Young's modulus (from 29 to 6 MPa). This is beneficial to the charge-transfer resistance, which decreases after implementing the electrolyte in half cells, demonstrating the improved interfacial contact. Most importantly, the phenyl groups change the interacting species at the silica interface. Cationic imidazolium species pi-stacked to the phenyl groups of the silica matrix, pushing the anions to the bulk of the ILE, which affects the ionic conductivity and electrochemical stability, and might affect the quality of the SEI in half cells. In essence, the work at hand can be used as a directory to improve mechanical characteristics and modify and control functional properties of ionogel electrolytes.

Photocatalytic Performance of Undoped and Al-Doped ZnO Nanoparticles in the Degradation of Rhodamine B under UV-Visible Light:The Role of Defects and Morphology.

Quasi-spherical undoped ZnO and Al-doped ZnO nanoparticles with different aluminum content, ranging from 0.5 to 5 at% of Al with respect to Zn, were synthesized. These nanoparticles were evaluated as photocatalysts in the photodegradation of the Rhodamine B (RhB) dye aqueous solution under UV-visible light irradiation. The undoped ZnO nanopowder annealed at 400 °C resulted in the highest degradation efficiency of ca. 81% after 4 h under green light irradiation (525 nm), in the presence of 5 mg of catalyst. The samples were characterized using ICP-OES, PXRD, TEM, FT-IR, 27Al-MAS NMR, UV-Vis and steady-state PL. The effect of Al-doping on the phase structure, shape and particle size was also investigated. Additional information arose from the annealed nanomaterials under dynamic N2 at different temperatures (400 and 550 °C). The position of aluminum in the ZnO lattice was identified by means of 27Al-MAS NMR. FT-IR gave further information about the type of tetrahedral sites occupied by aluminum. Photoluminescence showed that the insertion of dopant increases the oxygen vacancies reducing the peroxide-like species responsible for photocatalysis. The annealing temperature helps increase the number of red-emitting centers up to 400 °C, while at 550 °C, the photocatalytic performance drops due to the aggregation tendency.

Precursor Design Strategies for the Low-Temperature Synthesis of Functional Oxides: It's All in the Chemistry.

Solution-based (multi)metal oxide synthesis has been carried out employing a large diversity of precursor routes. The selection of an appropriate synthesis strategy is frequently dictated by the resulting material properties, although this choice should also be based on green chemistry principles, atom economy considerations and energy efficiency. In order to limit the required energy budget to convert the chemical precursor to the target oxide material, various approaches were recently reported. This Review summarizes some frequently encountered low-temperature routes, critically assessing their application window and advantages. More specifically, auto-combustion synthesis, UV-assisted decomposition routes, sol-gel network adjustments and precursor complex design concepts are discussed. It is expected that this toolbox of low-temperature strategies may assist further progress in the field, stimulating novel applications, such as flexible electronics or organic-oxide hybrid materials, which are very sensitive to the temperature requirements.

Reversible Surface Engineering via Nitrone-Mediated Radical Coupling.

Efficient and simple polymer conjugation reactions are critical for introducing functionalities on surfaces. For polymer surface grafting, postpolymerization modifications are often required, which can impose a significant synthetic hurdle. Here, we report two strategies that allow for reversible surface engineering via nitrone-mediated radical coupling (NMRC). Macroradicals stemming from the activation of polymers generated by copper-mediated radical polymerization are grafted via radical trapping with a surface-immobilized nitrone or a solution-borne nitrone. Since the product of NMRC coupling features an alkoxyamine linker, the grafting reactions can be reversed or chain insertions can be performed via nitroxide-mediated polymerization (NMP). Poly( n-butyl acrylate) ( Mn = 1570 g·mol-1, D̵ = 1.12) with a bromine terminus was reversibly grafted to planar silicon substrates or silica nanoparticles as successfully evidenced via X-ray photoelectron spectroscopy (XPS), time-of-flight secondary ion mass spectrometry, and grazing angle attenuated total reflection Fourier-transform infrared spectroscopy (GAATR-FTIR). NMP chain insertions of styrene are evidenced via GAATR-FTIR. On silica nanoparticles, an NMRC grafting density of close to 0.21 chains per nm2 was determined by dynamic light scattering and thermogravimetric analysis. Concomitantly, a simple way to decorate particles with nitroxide radicals with precise control over the radical concentration is introduced. Silica microparticles and zinc oxide, barium titanate, and silicon nanoparticles were successfully functionalized.

Understanding the Importance of Cu(I) Intermediates in Self-Reducing Molecular Inks for Flexible Electronics.

Fast and scalable low-temperature deposition of microscale metallic features is of utmost importance for the development of future flexible smart applications including sensors, wireless communication, and wearables. Recently, a new class of metal-organic decomposition (MOD) copper inks was developed, consisting of self-reducing copper formate containing amine complexes. From these novel inks, copper metal features with outstanding electrical conductivity (±105 S cm-1) are deposited at a temperature of 150 °C or less, which is well below the reduction temperature of orthorhombic α-copper formate (around 225 °C). However, the underlying principle of this reaction mechanism and the relationship between the corresponding temperature shift and the amine coordination are still under debate. The current study provides a full explanation for the shift in reduction temperatures via in situ characterization. The results clearly indicate that the structural resemblance and stability of the Cu(II) starting compound and the occurring Cu(I) intermediate during the in situ reduction are the two main variables that rationalize the temperature shift. As such, the thermal compatibility of copper MOD inks with conventional plastic substrates such as polyethylene terephthalate can be explained, based on metal-organic complex properties.

Chemical composition of an aqueous oxalato-/citrato-VO(2+) solution as determinant for vanadium oxide phase formation.

Aqueous solutions of oxalato- and citrato-VO(2+) complexes are prepared, and their ligand exchange reaction is investigated as a function of the amount of citrate present in the aqueous solution via continuous-wave electron paramagnetic resonance (CW EPR) and hyperfine sublevel correlation (HYSCORE) spectroscopy. With a low amount of citrate, monomeric cis-oxalato-VO(2+) complexes occur with a distorted square-pyramidal geometry. As the amount of citrate increases, oxalate is gradually exchanged for citrate. This leads to (i) an intermediate situation of monomeric VO(2+) complexes with a mix of oxalate/citrate ligands and (ii) a final situation of both monomeric and dimeric complexes with exclusively citrato ligands. The monomeric citrato-VO(2+) complexes dominate (abundance > 80%) and are characterized by a 6-fold chelation of the vanadium(IV) ion by 4 RCO2(-) ligands at the equatorial positions and a H2O/R-OH ligand at the axial position. The different redox stabilities of these complexes, relative to that of dissolved O2 in the aqueous solution, is analyzed via (51)V NMR. It is shown that the oxidation rate is the highest for the oxalato-VO(2+) complexes. In addition, the stability of the VO(2+) complexes can be drastically improved by evacuation of the dissolved O2 from the solution and subsequent storage in a N2 ambient atmosphere. The vanadium oxide phase formation process, starting with the chemical solution deposition of the aqueous solutions and continuing with subsequent processing in an ambient 0.1% O2 atmosphere, differs for the two complexes. The oxalato-VO(2+) complexes turn into the oxygen-deficient crystalline VO2 B at 400 °C, which then turns into crystalline V6O13 at 500 °C. In contrast, the citrato-VO(2+) complexes form an amorphous film at 400 °C that crystallizes into VO2 M1 and V6O13 at 500 °C.

The use of XAFS to determine the nature of interaction of iron and molybdenum metal salts within PS-b-P2VP micelles.

The poly(styrene)-block-poly(2-vinylpyridine) (PS-b-P2VP) micelle route is a well established method for the preparation of bimetallic nanoparticles used for the catalysis of carbon nanotubes and other applications like ultrahigh density storage devices, yet to date no information is available concerning the internal structure of the P2VP-metal salt complex. For the first time, XAFS measurements were performed on micelles loaded with either iron(III) chloride or molybdenum(V) chloride and a combination of both. Analysis of the data revealed that iron is tetrahedrally coordinated within the core, whereas molybdenum is octahedrally coordinated in the pure loaded micelles and trigonally coordinated in the mixed micelles. For the bimetallic samples, analysis of the Fe and Mo K-edge data revealed the existence of an interaction between iron and molybdenum. This approach to obtain detailed structural information during the preparation of these catalyst samples will allow for a deeper understanding of the effects of structure on the function of catalysts used for CNT growth i.e. to explain differences in yield as well as potentially providing a deeper understanding of the CNT growth mechanism itself.

Polymeric Backbone Eutectogel Electrolytes for High-Energy Lithium-Ion Batteries.

This work introduces a polymeric backbone eutectogel (P-ETG) hybrid solid-state electrolyte with an N-isopropylacrylamide (NIPAM) backbone for high-energy lithium-ion batteries (LIBs). The NIPAM-based P-ETG is (electro)chemically compatible with commercially relevant positive electrode materials such as the nickel-rich layered oxide LiNi0.6Mn0.2Co0.2O2 (NMC622). The chemical compatibility was demonstrated through (physico)chemical characterization methods. The nonexistence (within detection limits) of interfacial reactions between the electrolyte and the positive electrode, the unchanged bulk crystallographic composition, and the absence of transition metal ions leaching from the positive electrode in contact with the electrolyte were demonstrated by Fourier transform infrared spectroscopy, powder X-ray diffraction, and elemental analysis, respectively. Moreover, the NIPAM-based P-ETG demonstrates a wide electrochemical stability window (1.5-5.0 V vs Li+/Li) and a reasonably high ionic conductivity at room temperature (0.82 mS cm-1). The electrochemical compatibility of a high-potential NMC622-containing positive electrode and the P-ETG is further demonstrated in Li|P-ETG|NMC622 cells, which deliver a discharge capacity of 134, 110, and 97 mAh g-1 at C/5, C/2, and 1C, respectively, after 90 cycles. The Coulombic efficiency is >95% at C/5, C/2, and 1C. Hence, gaining scientific insights into the compatibility of the electrolytes with positive electrode materials that are relevant to the commercial market, like NMC622, is important because this requires going beyond the electrolyte design itself, which is essential to their practical applications.

Solution-gel-based surface modification of LiNi0.5Mn1.5O4-δ with amorphous Li-Ti-O coating.

LNMO (LiNi0.5Mn1.5O4-δ) is a high-energy density positive electrode material for lithium ion batteries. Unfortunately, it suffers from capacity loss and impedance rise during cycling due to electrolyte oxidation and electrode/electrolyte interface instabilities at high operating voltages. Here, a solution-gel synthesis route was used to coat 0.5-2.5 µm LNMO particles with amorphous Li-Ti-O (LTO) for improved Li conduction, surface structural stability and cyclability. High-angle annular dark-field scanning transmission electron microscopy (HAADF-STEM) analysis coupled with energy dispersive X-ray (EDX) showed Ti-rich amorphous coatings/islands or Ti-rich spinel layers on many of the LTO-modified LNMO facets, with a thickness varying from about 1 to 10 nm. The surface modification in the form of amorphous islands was mostly possible on high-energy crystal facets. Physicochemical observations were used to propose a molecular mechanism for the surface modification, combining insights from metalorganic chemistry with the crystallographic properties of LNMO. The improvements in functional properties were investigated in half cells. The cell impedance increased faster for the bare LNMO compared to amorphous LTO modified LNMO, resulting in Rct values as high as 1247 Ω (after 1000 cycles) for bare LNMO, against 216 Ω for the modified material. At 10C, the modified material boosted a 15% increase in average discharge capacity. The improvements in electrochemical performance were attributed to the increase in electrochemically active surface area, as well as to improved HF-scavenging, resulting in the formation of protective byproducts, generating a more stable interface during prolonged cycling.

Tuning the dimensions of ZnO nanorod arrays for application in hybrid photovoltaics.

ZnO nanorod arrays are a very eligible option as electron acceptor material in hybrid solar cells, owing to their favorable electrical properties and abundance of available, easy, and low-cost synthesis methods. To become truly effective in this field, a major prerequisite is the ability to tune the nanorod dimensions towards optimal compatibility with electron-donating absorber materials. In this work, a water-based seeding and growth procedure is used to synthesize ZnO nanorods. The nanorod diameter is tuned either by modifying the zinc concentration of the seeding solution or by changing the concentration of the hydrothermal growth solution. The consequences of this morphological tailoring in the performance of hybrid solar cells are investigated, which leads to a new record efficiency of 0.82 % for hydrothermally grown ZnO nanorods of size 300 nm in combination with poly(3-hexylthiophene-2,5-diyl) (P3HT). This improvement is attributed to a combined effect of nanorod diameter and orientation, and possibly to a better alignment of the P3HT backbone resulting in improved charge transport.

The Influence of Synthesis Method on the Local Structure and Electrochemical Properties of Li-Rich/Mn-Rich NMC Cathode Materials for Li-Ion Batteries.

Electrochemical energy storage plays a vital role in combating global climate change. Nowadays lithium-ion battery technology remains the most prominent technology for rechargeable batteries. A key performance-limiting factor of lithium-ion batteries is the active material of the positive electrode (cathode). Lithium- and manganese-rich nickel manganese cobalt oxide (LMR-NMC) cathode materials for Li-ion batteries are extensively investigated due to their high specific discharge capacities (>280 mAh/g). However, these materials are prone to severe capacity and voltage fade, which deteriorates the electrochemical performance. Capacity and voltage fade are strongly correlated with the particle morphology and nano- and microstructure of LMR-NMCs. By selecting an adequate synthesis strategy, the particle morphology and structure can be controlled, as such steering the electrochemical properties. In this manuscript we comparatively assessed the morphology and nanostructure of LMR-NMC (Li1.2Ni0.13Mn0.54Co0.13O2) prepared via an environmentally friendly aqueous solution-gel and co-precipitation route, respectively. The solution-gel (SG) synthesized material shows a Ni-enriched spinel-type surface layer at the {200} facets, which, based on our post-mortem high-angle annual dark-field scanning transmission electron microscopy and selected-area electron diffraction analysis, could partly explain the retarded voltage fade compared to the co-precipitation (CP) synthesized material. In addition, deviations in voltage fade and capacity fade (the latter being larger for the SG material) could also be correlated with the different particle morphology obtained for both materials.

Sunlight-Powered Reverse Water Gas Shift Reaction Catalysed by Plasmonic Au/TiO2 Nanocatalysts: Effects of Au Particle Size on the Activity and Selectivity.

This study reports the low temperature and low pressure conversion (up to 160 °C, p = 3.5 bar) of CO2 and H2 to CO using plasmonic Au/TiO2 nanocatalysts and mildly concentrated artificial sunlight as the sole energy source (up to 13.9 kW·m-2 = 13.9 suns). To distinguish between photothermal and non-thermal contributors, we investigated the impact of the Au nanoparticle size and light intensity on the activity and selectivity of the catalyst. A comparative study between P25 TiO2-supported Au nanocatalysts of a size of 6 nm and 16 nm displayed a 15 times higher activity for the smaller particles, which can only partially be attributed to the higher Au surface area. Other factors that may play a role are e.g., the electronic contact between Au and TiO2 and the ratio between plasmonic absorption and scattering. Both catalysts displayed ≥84% selectivity for CO (side product is CH4). Furthermore, we demonstrated that the catalytic activity of Au/TiO2 increases exponentially with increasing light intensity, which indicated the presence of a photothermal contributor. In dark, however, both Au/TiO2 catalysts solely produced CH4 at the same catalyst bed temperature (160 °C). We propose that the difference in selectivity is caused by the promotion of CO desorption through charge transfer of plasmon generated charges (as a non-thermal contributor).

Aqueous solutions for low-temperature photoannealing of functional oxide films: reaching the 400 °C Si-technology integration barrier.

Functional oxide films were obtained at low temperature by combination of aqueous precursors and a UV-assisted annealing process (aqueous photochemical solution deposition). For a PbTiO(3) model system, functional ferroelectric perovskite films were prepared at only 400 °C, a temperature compatible with the current Si-technology demands. Intrinsically photosensitive and environmentally friendly aqueous precursors can be prepared for most of the functional multimetal oxides, as additionally demonstrated here for multiferroic BiFeO(3), yielding virtually unlimited possibilities for this low-temperature fabrication technology.

Layered perovskite-like Pb2Fe2O5 structure as a parent matrix for the nucleation and growth of crystallographic shear planes.

The Pb(2)Fe(2)O(5) compound with a layered intergrowth structure has been prepared by a solid-state reaction at 700 °C. The incommensurate compound crystallizes in a tetragonal system with a = 3.9037(2) Å, c = 3.9996(4) Å, and q = 0.1186(4)c*, or when treated as a commensurate approximant, a = 3.9047(2) Å, c = 36.000(3) Å, space group I4/mmm. The crystal structure of Pb(2)Fe(2)O(5) was resolved from transmission electron microscopy data. Atomic coordinates and occupancies of the cation positions were estimated from high-angle annular dark-field scanning transmission electron microscopy data. Direct visualization of the positions of the oxygen atoms was possible using annular bright-field scanning transmission electron microscopy. The structure can be represented as an intergrowth of perovskite blocks and partially disordered blocks with a structure similar to that of the Bi(2)O(2) blocks in Aurivillius-type phases. The A-cation positions at the border of the perovskite block and the cation positions in the Aurivillius-type blocks are jointly occupied by Pb(2+) and Fe(3+) cations, resulting in a layer sequence along the c axis: -PbO-FeO(2)-PbO-FeO(2)-Pb(7/8)Fe(1/8)-O(1-x)-Fe(5/8)Pb(3/8)-O(2)-Fe(5/8)Pb(3/8)-. Upon heating, the layered Pb(2)Fe(2)O(5) structure transforms into an anion-deficient perovskite modulated by periodically spaced crystallographic shear (CS) planes. Considering the layered Pb(2)Fe(2)O(5) structure as a parent matrix for the nucleation and growth of CS planes allows an explanation of the specific microstructure observed for the CS structures in the Pb-Fe-O system.

Dielectric Barrier Discharge (DBD) Plasma Coating of Sulfur for Mitigation of Capacity Fade in Lithium-Sulfur Batteries.

Sulfur particles with a conductive polymer coating of poly(3,4-ethylene dioxythiophene) "PEDOT" were prepared by dielectric barrier discharge (DBD) plasma technology under atmospheric conditions (low temperature, ambient pressure). We report a solvent-free, low-cost, low-energy-consumption, safe, and low-risk process to make the material development and production compatible for sustainable technologies. Different coating protocols were developed to produce PEDOT-coated sulfur powders with electrical conductivity in the range of 10-8-10-5 S/cm. The raw sulfur powder (used as the reference) and (low-, optimum-, high-) PEDOT-coated sulfur powders were used to assemble lithium-sulfur (Li-S) cells with a high sulfur loading of ∼4.5 mg/cm2. Long-term galvanostatic cycling at C/10 for 100 cycles showed that the capacity fade was mitigated by ∼30% for the cells containing the optimum-PEDOT-coated sulfur in comparison to the reference Li-S cells with raw sulfur. Rate capability, cyclic voltammetry, and electrochemical impedance analyzes confirmed the improved behavior of the PEDOT-coated sulfur as an active material for lithium-sulfur batteries. The Li-S cells containing optimum-PEDOT-coated sulfur showed the highest reproducibility of their electrochemical properties. A wide variety of bulk and surface characterization methods including conductivity analysis, X-ray diffraction (XRD), scanning electron microscopy (SEM), Raman spectroscopy, X-ray photoelectron spectroscopy (XPS), and NMR spectroscopy were used to explain the chemical features and the superior behavior of Li-S cells using the optimum-PEDOT-coated sulfur material. Moreover, postmortem [SEM and Brunauer-Emmett-Teller (BET)] analyzes of uncoated and coated samples allowed us to exclude any significant effect at the electrode scale even after 70 cycles.

A limitation map of performance for porous electrodes in lithium-ion batteries.

Driven by expanding interest in battery storage solutions and the success story of lithium-ion batteries, the research for the discovery and optimization of new battery materials and concepts is at peak. The generation of experimental (dis)charge data using coin cells is fast and feasible and proves to be a favorite practice in the battery research labs. The quantitative interpretation of the data, however, is not trivial and decelerates the process of screening and optimization of electrode materials and recipes. Here, we introduce the concept of polarographic map and demonstrate how it can be leveraged to quantify the contribution of different non-equilibrium phenomena to the performance limitation and total polarization of a lithium-ion cell. We showcase the accuracy and diagnostic power of this approach by preparing and analyzing the electrochemical performance of 54 sets of LiNixMnyCo1-x-yO2 electrodes with different formulations and designs discharged in a range of 0.2C-5C.

An in-depth study of Sn substitution in Li-rich/Mn-rich NMC as a cathode material for Li-ion batteries.

Layered Li-rich/Mn-rich NMC (LMR-NMC) is characterized by high initial specific capacities of more than 250 mA h g-1, lower cost due to a lower Co content and higher thermal stability than LiCoO2. However, its commercialisation is currently still hampered by significant voltage fade, which is caused by irreversible transition metal ion migration to emptied Li positions via tetrahedral interstices upon electrochemical cycling. This structural change is strongly correlated with anionic redox chemistry of the oxygen sublattice and has a detrimental effect on electrochemical performance. In a fully charged state, up to 4.8 V vs. Li/Li+, Mn4+ is prone to migrate to the Li layer. The replacement of Mn4+ for an isovalent cation such as Sn4+ which does not tend to adopt tetrahedral coordination and shows a higher metal-oxygen bond strength is considered to be a viable strategy to stabilize the layered structure upon extended electrochemical cycling, hereby decreasing voltage fade. The influence of Sn4+ on the voltage fade in partially charged LMR-NMC is not yet reported in the literature, and therefore, we have investigated the structure and the corresponding electrochemical properties of LMR-NMC with different Sn concentrations. We determined the substitution limit of Sn4+ in Li1.2Ni0.13Co0.13Mn0.54-xSnxO2 by powder X-ray diffraction and transmission electron microscopy to be x≈ 0.045. The limited solubility of Sn is subsequently confirmed by density functional theory calculations. Voltage fade for x = 0 and x = 0.027 has been comparatively assessed within the 3.00 V-4.55 V (vs. Li/Li+) potential window, from which it is concluded that replacing Mn4+ by Sn4+ cannot be considered as a viable strategy to inhibit voltage fade within this window, at least with the given restricted doping level.

Hydrothermal synthesis of ZnO nanorods: a statistical determination of the significant parameters in view of reducing the diameter.

In this paper a 2(8-4) fractional factorial design of experiments is applied to identify the important parameters that affect the average diameter of ZnO rods, synthesized by means of a hydrothermal procedure. A water-based Zn(2+) precursor is used for the formation of one-dimensional ZnO particles, without the presence of an organic additive. Results indicate that, at the investigated levels, four of the parameters have a significant effect on the mean diameter. These are the temperature, the heating rate, stirring and an ultrasonic pre-treatment of the precursor solution. Experiments carried out with zinc acetate and zinc chloride do not show a significant difference in rod diameter. Other parameters that do not show a significant effect are the concentration of Zn(2+), the molar ratio between the hydroxyl and the zinc ions, and the reaction time. Interactions are observed between stirring and an ultrasonic pre-treatment and between the zinc concentration and the OH:Zn ratio. By fixing the significant factors at their optimal value it is possible to decrease the mean diameter. The particles are characterized by means of x-ray diffraction (XRD) and transmission electron microscopy (TEM).

In Situ Mechanical Analysis of the Nanoscopic Solid Electrolyte Interphase on Anodes of Li-Ion Batteries.

The interfacial decomposition products forming the so-called solid-electrolyte interphase (SEI) significantly determine the destiny of a Li-ion battery. Ultimate knowledge of its detailed behavior and better control are required for higher rates, longer life-time, and increased safety. Employing an electrochemical surface force apparatus, it is possible to control the growth and to investigate the mechanical properties of an SEI in a lithium-ion battery environment. This new approach is here introduced on a gold model system and reveals a compressible film at all stages of SEI growth. The demonstrated methodology provides a unique tool for analyzing electrochemical battery interfaces, in particular in view of alternative electrolyte formulations and artificial interfaces.