Excited state electron transfer from aminopyrene to graphene: a combined experimental and theoretical study.

The quenching of the fluorescence of 1-aminopyrene (1-Ap) by reduced graphene oxide (rGO) has been investigated using spectroscopic techniques. In spite of the upward curvature in the Stern-Volmer plot, the unchanged spectral signature of the absorption of 1-Ap in the presence of rGO and the decrease in fluorescence lifetime with increasing rGO concentration point toward the dynamic nature of the quenching. Detailed analysis of steady state and time-resolved spectroscopic data has shown that the quenching arises due to the photoinduced electron transfer from 1-Ap to rGO. This is again supported by estimating the Gibb's free energy change for the ground as well as excited state electron transfer. Ab initio calculations under the density functional theory (DFT) formalism reveal that the possibility of π-π stacking is very slim in the 1-Ap-rGO system and the electron density resides completely on 1-Ap in the highest occupied molecular orbital (HOMO) and on graphene in the lowest unoccupied molecular orbital (LUMO), supporting the experimental findings of the intermolecular electron transfer between 1-Ap and rGO in the excited state.

Graphene-Augmented Polymer Stabilization: Drastically Reduced and Temperature-Independent Threshold and Improved Contrast Liquid Crystal Device.

Polymers reinforced with nanofillers, especially graphene in recent times, have continued to attract attention to realize novel materials that are cheap and also have better properties. At a different level, encapsulating liquid crystals (LCs) in polymer networks not only adds mechanical strength, but could also result in device-based refractive index mismatch. Here, we describe a novel strategy combining the best of both these concepts to create graphene-incorporated polymer-stabilized LC (PSLC) devices. The presence of graphene associated with the virtual surface of the polymer network besides introducing distinct morphological changes to the polymer architecture as seen by electron microscopy brings out several advantages for the PSLC characteristics, which include 7-fold lowered critical voltage, its temperature invariance, and enhanced contrast ratio between field-off scattering/field-on transparent states. The results bring to fore the importance of working at very-dilute-concentration limits of the filler nanoparticles in augmenting the desired properties. These observations open up a new vista for polymer-graphene composites in the area of device engineering, including substrate-free smart windows.

Dip-pen lithography using pens of different thicknesses.

A laboratory method to produce AFM tips of different sizes has been developed based on laser irradiation of the commercial silicon nitride tips. A few shots of 60 mJ at 355 nm were found adequate to induce the desired bluntness from 40 nm to 500 nm in a controlled way. Dip-pen nanolithography (DPN) has been performed with the blunt tips using a colloidal ink consisting of Pd nanocrystals coated with polyvinyl pyrrolidone. The line patterns drawn bear a direct relation with the tip morphology, wider the tip, broader are the patterns, in general. The rate of deposition also increases with the tip dimension, but is not as much proportional for larger tips. The study highlights the potential ability of DPN in integrating nano and microelectronics.

A facile method of producing femtoliter metal cups by pulsed laser ablation.

Cuplike structures of Au, Ag, Cu, Zn, Nb, Cd, Al, In, and Sn in the size range of 300 nm to a few micrometers with an internal volume of a few femtoliters have been produced by the laser ablation of metal targets in a vacuum, by optimizing, in each case, the laser fluence and the substrate temperature. The metal droplets impinging on the substrate seem to undergo a hydraulic jump driven by the surface tension forces before solidifying into cups. The cups are robust and can be functionalized with biomarkers, filled with nanoparticle sols, oxidized to crucibles, or detached from the substrate without causing any deformation. We envisage their potential applications as femtoliter metal containers.

Pyramidal nanostructures of zinc oxide.

Zinc oxide (ZnO) nanostructures have been prepared by pulsed laser deposition of the oxide onto Si(100) substrate at 600 degrees C. An examination of the morphology using atomic force microscopy and scanning electron microscopy reveals well formed pyramidal structures consistent with the growth habit of ZnO. A domain matched epitaxy across the interface makes the ZnO pyramids orient along the axes of Si(100) surface. The pyramidal nanostructures signify an intermediate state in the growth of hexagonal nanorods of ZnO. The hardness of the nanostructures as well as their response to oxygen gas have been investigated using nanoindentation and conducting probe methods respectively. ZnO nanostructures are much harder than their bulk. The hardness of ZnO pyramids obtained by nanoindentation is 70 +/- 10 GPa which is about one order more that of bulk ZnO. Besides, the nanostructures exhibit high sensitivity towards oxygen. A 70% increase in the resistance of ZnO nanostructures is observed when exposed to oxygen atmosphere.

Gold-coated conducting-atomic force microscopy probes.

Some aspects of the performance of gold-coated conductive probes used in conducting atomic force microscopy (C-AFM) technique are discussed. The resistance of the nanocontact between the gold-coated AFM tip and the graphite substrate has been monitored at various applied forces. For small forces (<50 nN), resistance on the order of a few kiloohms was observed. Minimal contact resistance was observed for forces in the range 100-150 nN, beyond which the tip seems to undergo plastic deformation. The resistance of the nanocontact increased when current on the order of 100 microA was allowed to pass through, finally resulting in melting of the gold coating.

Gravity-free hydraulic jumps and metal femtoliter cups.

Hydraulic jumps created by gravity are seen everyday in the kitchen sink. We show that at small scales a circular hydraulic jump can be created in the absence of gravity by surface tension. The theory is motivated by our experimental finding of a height discontinuity in spreading submicron molten metal droplets created by pulsed-laser ablation. By careful control of initial conditions, this leads to solid femtoliter cups of gold, silver, copper, niobium, and tin.