Non-Invasive Optical Coherence Tomography Data-Based Quantitative Algorithm for the Assessment of Residual Adhesive on Bracket-Removed Dental Surface.

The aim of this study was to quantitatively assess the residual adhesive on orthodontic ceramic bracket-removed dental surface. In orthodontic process, ceramic bracket was repeated debonding physically, then the adhesive remained on the dental surface. The residual adhesive caused a lack of adhesive strength between dental and ceramic bracket. Since commonly used adhesive in orthodontics is translucent, residual adhesive is hard to be detected with conventional microscopes. Therefore, 1310 nm center wavelength swept-source OCT system based on laboratory customized image processing algorithm was used for the precise detection of residual adhesive on tooth surface. The algorithm separates residual adhesive from dental surface by comparing the height of adjacent B-scan images, while providing color-scaled images emphasizing the thickness information of residual adhesive. Finally, the acquired results were compared with microscopic and adhesive remnant index scoring gold standards, while the comparison confirmed the potential merits and the improvements of the proposed method over gold standards.

A new optical technique to monitor joint motion using position sensitive detector.

BACKGROUND: Evaluation of joint movements is essential to choose an appropriate rehabilitation protocol for a patient. OBJECTIVE: The aim of this study is to suggest an alternative optical technique for measurement of joint angle which is convenient, inexpensive, and can be operated in real time. METHODS: According to the principle of the triangulation method, position sensitive detector (PSD) converts reflected light signals into distance-related voltages. Various parameters were investigated to increase detection range and resolution of joint angle measurements. RESULTS: The accuracy of the suggested optical sensor was verified by comparing with a commercial goniometer and 3D motion capture system. CONCLUSIONS: This method can be applied to monitor recovery progress for the patient in rehabilitation and sport science.

Development of multi-colored LED system for therapeutic application.

BACKGROUND: The evaluation and control of lighting is crucial in physiological, biomedical, and industrial fields. Many kinds of lighting techniques based on LED have been developed due to its advantages. OBJECTIVE: The aim of this study is to develop the multi-colored LED system for healing purposes. METHODS: Light source with three-color chip LEDs was investigated to detect the dominant wavelength. RESULTS: The results show that the additive principle by three-color LEDs can be successfully applied to lighting system by generating a variety of colors. CONCLUSIONS: The results are expected to be useful in the field of light therapy and medicine. Applications of the developed light system are lighting therapies such as stimulating blood circulation and digestive processes, and controlling inflammation.

Simple LED spectrophotometer for analysis of color information.

A spectrophotometer is the basic measuring equipment essential to most research activity fields requiring samples to be measured, such as physics, biotechnology and food engineering. This paper proposes a system that is able to detect sample concentration and color information by using LED and color sensor. Purity and wavelength information can be detected by CIE diagram, and the concentration can be estimated with purity information. This method is more economical and efficient than existing spectrophotometry, and can also be used by ordinary persons. This contribution is applicable to a number of fields because it can be used as a colorimeter to detect the wavelength and purity of samples.

Evaluation of the possibility and response characteristics of laser-induced tactile sensation.

In this study, we examined the possibility and perceptual response characteristics of tactile sense induced by laser stimulation to the finger with different laser energy densities through human response experiments. 15 healthy adult males and 4 healthy adult females with an age of 22.6±2.2 years were tested. A frequency-doubled Q-switched laser was used with a wavelength of 532 nm and a 5 ns pulse width. The experimental trial spanned a total of 30 s and included a rest phase (19 s), a stimulation phase (7 s), and a response phase (4 s). During the rest phase, subjects kept their fingers comfortable. During the stimulation phase, one of three types of laser energy density (13.5, 16.6, 19.8 mJ/cm(2)) or a sham stimulation was used to irradiate the distal phalanx on the right index finger. During the response phase, the cognitive response to the laser stimulation was recorded by a PC by pressing the response button. The confusion matrix was configured to evaluate the possibility that the tactile sense was caused by the laser. In addition, changes in the response characteristics were observed according to three types of laser energy densities. From the analysis of the confusion matrix, the accuracy and sensitivity were not high. In contrast, precision and specificity were found to be high. Furthermore, there was a strong positive correlation between the laser irradiation and tactile perception, indicating that tactile sense can be induced using a laser in a mid-air manner. In addition, it was found that as the laser energy density increased, the tactile perception possibility also increased.

Photomechanical effect on Type I collagen using pulsed diode laser.

BACKGROUND: As the most abundant protein in human tissues, the use of collagen is essential in the fields of biological science and medicine. OBJECTIVE: The aim of this study is to investigate the mechanical effect of pulsed laser irradiation on collagen tissue. METHODS: With various laser parameters such as peak power, pulse width, and repetition rate, the induced stresses on samples were measured and analyzed. Monte Carlo simulation was performed to investigate the effect of laser parameters on the collagen sample. RESULTS: The results indicated that the magnitude of mechanical stress could be controlled by various laser parameters. CONCLUSIONS: This study can be used in biostimulation for therapy and mechanoreceptor stimulation for tactile application.

Laser-induced thermoelastic effects can evoke tactile sensations.

Humans process a plethora of sensory information that is provided by various entities in the surrounding environment. Among the five major senses, technology for touch, haptics, is relatively young and has relatively limited applications largely due to its need for physical contact. In this article, we suggest a new way for non-contact haptic stimulation that uses laser, which has potential advantages such as mid-air stimulation, high spatial precision, and long working distance. We demonstrate such tactile stimulation can be enabled by laser-induced thermoelastic effects by means of physical and perceptual studies, as well as simulations. In the physical study, the mechanical effect of laser on a human skin sample is detected using low-power radiation in accordance with safety guidelines. Limited increases (< ~2.5 °C) in temperature at the surface of the skin, examined by both thermal camera and the Monte Carlo simulation, indicate that laser does not evoke heat-induced nociceptive sensation. In the human EEG study, brain responses to both mechanical and laser stimulation are consistent, along with subjective reports of the non-nociceptive sensation of laser stimuli.

Development of an optical fiber sensor for angular displacement measurements.

For diagnostic and therapeutic purposes, the joint angle measurement of a patient after an accident or a surgical operation is significant for monitoring and evaluating the recovering process. This paper proposed an optical fiber sensor for the measurement of angular displacement. The effect of beveled fiber angle on the detected light signal was investigated to find an appropriate mathematical model. Beveled fiber tips redirected the light over a range of angles away from the fiber axis. Inverse polynomial models were applied to directly obtain and display the joint angle change in real time with the Lab-VIEW program. The actual joint angle correlated well with the calculated LabVIEW output angle over the test range. The proposed optical sensor is simple, cost effective, small in size, and can evaluate the joint angle in real time. This method is expected to be useful in the field of rehabilitation and sport science.

A practical method for the detection of freezing of gait in patients with Parkinson's disease.

PURPOSE: Freezing of gait (FOG), increasing the fall risk and limiting the quality of life, is common at the advanced stage of Parkinson's disease, typically in old ages. A simple and unobtrusive FOG detection system with a small calculation load would make a fast presentation of on-demand cueing possible. The purpose of this study was to find a practical FOG detection system. PATIENTS AND METHODS: A sole-mounted sensor system was developed for an unobtrusive measurement of acceleration during gait. Twenty patients with Parkinson's disease participated in this study. A simple and fast time-domain method for the FOG detection was suggested and compared with the conventional frequency-domain method. The parameters used in the FOG detection were optimized for each patient. RESULTS: The calculation load was 1,154 times less in the time-domain method than the conventional method, and the FOG detection performance was comparable between the two domains (P=0.79) and depended on the window length (P<0.01) and dimension of sensor information (P=0.03). CONCLUSION: A minimally constraining sole-mounted sensor system was developed, and the suggested time-domain method showed comparable FOG detection performance to that of the conventional frequency-domain method. Three-dimensional sensor information and 3-4-second window length were desirable. The suggested system is expected to have more practical clinical applications.