Plasma enhanced atomic layer deposition of silicon nitride using magnetized very high frequency plasma.

To obtain high-quality SiNxfilms applicable to an extensive range of processes, such as gate spacers in fin field-effect transistors (FinFETs), the self-aligned quadruple patterning process, etc, a study of plasma with higher plasma density and lower plasma damage is crucial in addition to study on novel precursors for SiNxplasma-enhanced atomic layer deposition (PEALD) processes. In this study, a novel magnetized PEALD process was developed for depositing high-quality SiNxfilms using di(isopropylamino)silane (DIPAS) and magnetized N2plasma at a low substrate temperature of 200 °C. The properties of the deposited SiNxfilms were analyzed and compared with those obtained by the PEALD process using a non-magnetized N2plasma source under the same conditions. The PEALD SiNxfilm, produced using an external magnetic field (ranging from 0 to 100 G) during the plasma exposure step, exhibited a higher growth rate (∼1 Å/cycle) due to the increased plasma density. Additionally, it showed lower surface roughness, higher film density, and enhanced wet etch resistance compared to films deposited using the PEALD process with non-magnetized plasmas. This improvement can be attributed to the higher ion flux and lower ion energy of the magnetized plasma. The electrical characteristics, such as interface trap density and breakdown voltage, were also enhanced when the magnetized plasma was used for the PEALD process. Furthermore, when SiNxfilms were deposited on high-aspect-ratio (30:1) trench patterns using the magnetized PEALD process, an improved step coverage of over 98% was achieved, in contrast to the conformality of SiNxdeposited using non-magnetized plasma. This enhancement is possibly a result of deeper radical penetration enabled by the magnetized plasma.

Highly selective etching of SiNxover SiO2using ClF3/Cl2remote plasma.

Highly selective etching of silicon nitride over silicon oxide is one of the most important processes especially for the fabrication of vertical semiconductor devices including 3D NAND (Not And) devices. In this study, isotropic dry etching characteristics of SiNxand SiO2using ClF3/Cl2remote plasmas have been investigated. The increase of Cl2percent in ClF3/Cl2gas mixture increased etch selectivity of SiNxover SiO2while decreasing SiNxetch rate. By addition of 15% Cl to ClF3/Cl2, the etch selectivity higher than 500 could be obtained with the SiNxetch rate of ∼8 nm min-1, and the increase of Cl percent to 20% further increased the etch selectivity to higher than 1000. It was found that SiNxcan be etched through the reaction from Si-N to Si-F and Si-Cl (also from Si-Cl to Si-F) while SiO2can be etched only through the reaction from Si-O to Si-F, and which is also in extremely low reaction at room temperature. When SiNx/SiO2layer stack was etched using ClF3/Cl2(15%), extremely selective removal of SiNxlayer in the SiNx/SiO2layer stack could be obtained without noticeable etching of SiO2layer in the stack and without etch loading effect.

Synthesis and biological evaluation of novel N-benzyltriazolyl-hydroxamate derivatives as selective histone deacetylase 6 inhibitors.

Histone deacetylases (HDAC) regulate post-translational acetylation and the inhibition of these enzymes has emerged as an intriguing disease therapeutic. Among them, class IIb HDAC6 has the unique characteristic of mainly deacetylating cytoplasmic proteins, suggesting clinical applications for neurodegenerative diseases, inflammation, and cancer. In this study, we designed a novel N-benzyltriazolyl-hydroxamate scaffold based on the known HDAC6 inhibitors nexturastat A and tubastatin A. Among the 27 derivatives, 3-fluoro-4-((3-(2-fluorophenyl)-1H-1,2,4-triazol-1-yl)methyl)-N-hydroxybenzamide 4u (HDAC6 IC50 = 7.08 nM) showed nanomolar HDAC6 inhibitory activity with 42-fold selectivity over HDAC1. Structure-activity relationship (SAR) and computational docking studies were conducted to optimize the triazole capping group. Docking analysis revealed that the capping group aligned with the conserved L1 pocket of HDAC6 and was associated with subtype selectivity. Overall, our study explored the triazole-based biaryl capping group and its substitution and orientation, suggesting a rationale for the design of HDAC6-selective inhibitors.

Application of entire dental panorama image data in artificial intelligence model for age estimation.

BACKGROUND: Accurate age estimation is vital for clinical and forensic purposes. With the rapid advancement of artificial intelligence(AI) technologies, traditional methods relying on tooth development, while reliable, can be enhanced by leveraging deep learning, particularly neural networks. This study evaluated the efficiency of an AI model by applying the entire panoramic image for age estimation. The outcome performances were analyzed through supervised learning (SL) models. METHODS: Total of 27,877 dental panorama images from 5 to 90 years of age were classified by 2 types of grouping. In type 1 they were classified by each age and in type 2, applying heuristic grouping, the age over 20 years were classified by every 5 years. Wide ResNet (WRN) and DenseNet (DN) were used for supervised learning. In addition, the analysis with ± 3 years of deviation in both types were performed. RESULTS: For the DN model, while the type 1 grouping achieved an accuracy of 0.1016 and F1 score of 0.058, the type 2 achieved an accuracy of 0.3146 and F1 score of 0.2027. Incorporating ± 3years of deviation, the accuracy of type 1 and 2 were 0.281, 0.7323 respectively; and the F1 score were 0.1768, 0.6583 respectively. For the WRN model, while the type 1 grouping achieved an accuracy of 0.1041 and F1 score of 0.0599, the type 2 achieved an accuracy of 0.3182 and F1 score of 0.2071. Incorporating ± 3years of deviation, the accuracy of type 1 and 2 were 0.2716, 0.7323 respectively; and the F1 score were 0.1709, 0.6437 respectively. CONCLUSIONS: The application of entire panorama image data for supervised with classification by heuristics grouping with ± 3years of deviation for supervised learning models and demonstrated satisfactory outcome for the age estimation.

Reduction of EUV resist damage by neutral beam etching.

Even though EUV lithography has the advantage of implenting a finer pattern compared to ArF immersion lithography due to the use of 13.5 nm instead of 193 nm as the wavelength of the light source, due to the low energy of EUV light source, EUV resist has a thinner thickness than conventional ArF resist. EUV resist having such a thin thickness is more vulnerable to radiation damage received during the etching because of its low etch resistance and also tends to have a problem of low etch selectivity. In this study, the radiation damage to EUV resist during etching of hardmask materials such as Si3N4, SiO2, etc using CF4gas was compared between neutral beam etching (NBE) and ion beam etching (IBE). When NBE was used, after the etching of 20 nm thick EUV resist, the line edge roughness increase and the critical dimension change of EUV resist were reduced by ∼1/3 and ∼1/2, respectively, compared to those by IBE. Also, at that EUV etch depth, the root mean square surface roughness value of EUV resist etched by NBE was ∼2/3 compared to that by IBE on the average. It was also confirmed that the etching selectivity between SiO2, Si3N4, etc and EUV resist was higher for NBE compared to IBE. The less damage to the EUV resist and the higher etch selectivity of materials such as Si3N4and SiO2over EUV resist for NBE compared to IBE are believed to be related to the no potential energy released by the neutralization of the ions during the etching by NBE.

Practice considerations on the use of investigational anti-COVID-19 medications: Dosage, administration and monitoring.

WHAT IS KNOWN AND OBJECTIVE: Understanding investigational medications is important. Many older drugs are being investigated for repurposing against COVID-19. We comment on various drugs currently undergoing such trials to optimize their safe use. COMMENT: We describe medications used during early COVID-19 outbreaks in South Korea, focusing on practice aspects including the method of drug administration, drug formulation, patient-monitoring for adverse reactions and drug interactions informed by our experience during the 2015 outbreak of Middle East respiratory syndrome (MERS). We comment on hydroxychloroquine, chloroquine, lopinavir/ritonavir with zinc supplement, remdesivir, tocilizumab, ciclesonide, niclosamide and high-dose intravenous immunoglobulin (IVIG). WHAT IS NEW AND CONCLUSION: Effective therapies are urgently needed to manage COVID-19, and existing drugs such as antivirals and antimalarials are under investigation for repurposing to meet this need. This process requires up-to-date drug information to ensure optimum use, particularly safety and efficacy profiles of the medications, until convincing evidence is reported.

Fungal Diversity in Intertidal Mudflats and Abandoned Solar Salterns as a Source for Biological Resources.

Intertidal zones are unique environments that are known to be ecological hot spots. In this study, sediments were collected from mudflats and decommissioned salterns on three islands in the Yellow Sea of South Korea. The diversity analysis targeted both isolates and unculturable fungi via Illumina sequencing, and the natural recovery of the abandoned salterns was assessed. The phylogeny and bioactivities of the fungal isolates were investigated. The community analysis showed that the abandoned saltern in Yongyudo has not recovered to a mudflat, while the other salterns have almost recovered. The results suggested that a period of more than 35 years may be required to return abandoned salterns to mudflats via natural restoration. Gigasporales sp. and Umbelopsis sp. were selected as the indicators of mudflats. Among the 53 isolates, 18 appeared to be candidate novel species, and 28 exhibited bioactivity. Phoma sp., Cladosporium sphaerospermum, Penicillium sp. and Pseudeurotium bakeri, and Aspergillus urmiensis showed antioxidant, tyrosinase inhibition, antifungal, and quorum-sensing inhibition activities, respectively, which has not been reported previously. This study provides reliable fungal diversity information for mudflats and abandoned salterns and shows that they are highly valuable for bioprospecting not only for novel microorganisms but also for novel bioactive compounds.

The influence of a patient counseling training session on pharmacy students' self-perceived communication skills, confidence levels, and attitudes about communication skills training.

BACKGROUND: The ability to communicate effectively is an essential skill for a pharmacist. However, the curricula of most pharmacy schools in South Korea do not include communication skills training (CST). This study aims to evaluate the effects of CST in pharmacy education. METHODS: This study was a comparison of pre- and post-intervention surveys completed by sixty fifth-year pharmacy students who participated in communication skills and patient counseling training during the spring 2017 semester. The students were asked to respond to 49 questions addressing 4 self-assessment categories: communication skills (24), attitudes (19), and confidence levels (2) at the beginning and end of the CST, and their perception of CST (4) after completing the course. The training session included lectures, small group work, role play, videos, and performance feedback by a tutor. Data were analyzed using the paired t-test with Bonferroni's correction for multiple comparisons. The open-ended questions were analyzed using inductive content analysis. RESULTS: The pharmacy students' self-assessment of their communication skills, attitudes toward the communication course, and confidence levels showed significant improvement after the CST. Most students (96.7%) indicated the necessity of a pharmacy communication curriculum. They responded that CST is helpful for effective communication with patients (33.3%) and other healthcare professionals (31.7%). Role-playing was reported as the most preferred learning method (58.3%). CONCLUSIONS: CST significantly impacted pharmacy students' skills, attitudes, and confidence levels related to communication skills and patient counseling. These findings indicate that communications training should be included in the regular curriculum of pharmacy schools.

The effect of communication skills training on patient-pharmacist communication in pharmacy education: a meta-analysis.

Communication skills in pharmacy education and practice are increasingly regarded as a crucial component. However, thus far, estimating of the overall communication skills training (CST) effects in a variety of outcomes is lacking. The aim of this study was to synthesize the effects of CST in pharmacy education by performing a meta-analysis of CST studies. We searched MEDLINE, EMBASE, ERIC, CINAHL, PsycINFO, Cochrane Library, Web of Science, Communication and Mass Media Complete (CMMC), key journals, and bibliographic databases. The effect sizes (ESs) were extracted and pooled in random effects meta-analyses. We assessed the quality of the study using the Medical Education Research Study Quality Instrument (MERSQI). From 34,737 articles, 9 studies were included in this meta-analysis. The overall effect size for CST was 0.611 (95% CI 0.327-0.895), and it was statistically significant (p = 0.000). We found based on the subgroup analyses that CST has a large effect size when it used stand-alone courses, lecture-lab based courses, video recordings, feedback, training for 2 or more semesters, hours per week ≥5 h and external assessments. For the CST effect, the effect sizes were ranked in order of confidence, knowledge, skills, and attitudes. The result of the meta-regression is that the total number of attendees is significantly negatively correlated with the effect sizes of the CST. The findings of the present meta-analysis provide evidence that CST in pharmacy education may act as an efficient way to improve the communication competency of students, and it may serve as a guide for pharmacy educators.

Diversity and Ecology of Marine Algicolous Arthrinium Species as a Source of Bioactive Natural Products.

In our previous study, all Arthrinium isolates from Sargassum sp. showed high bioactivities, but studies on marine Arthrinium spp. are insufficient. In this study, a phylogenetic analysis of 28 Arthrinium isolates from seaweeds and egg masses of Arctoscopus japonicus was conducted using internal transcribed spacers, nuclear large subunit rDNA, ß-tubulin, and translation elongation factor region sequences, and their bioactivities were investigated. They were analyzed as 15 species, and 11 of them were found to be new species. Most of the extracts exhibited radical-scavenging activity, and some showed antifungal activities, tyrosinase inhibition, and quorum sensing inhibition. It was implied that marine algicolous Arthrinium spp. support the regulation of reactive oxygen species in symbiotic algae and protect against pathogens and bacterial biofilm formation. The antioxidant from Arthrinium sp. 10 KUC21332 was separated by bioassay-guided isolation and identified to be gentisyl alcohol, and the antioxidant of Arthrinium saccharicola KUC21221 was identical. These results demonstrate that many unexploited Arthrinium species still exist in marine environments and that they are a great source of bioactive compounds.

Arabidopsis WRKY55 Transcription Factor Enhances Soft Rot Disease Resistance with ORA59.

Pectobacterium is a major bacterial causal agent leading to soft rot disease in host plants. With the Arabidopsis-Pectobacterium pathosystem, we investigated the function of an Arabidopsis thaliana WRKY55 during defense responses to Pectobacterium carotovorum ssp. carotovorum (Pcc). Pcc-infection specifically induced WRKY55 gene expression. The overexpression of WRKY55 was resistant to the Pcc infection, while wrky55 knockout plants compromised the defense responses against Pcc. WRKY55 expression was mediated via Arabidopsis COI1-dependent signaling pathway showing that WRKY55 can contribute to the gene expression of jasmonic acid-mediated defense marker genes such as PDF1.2 and LOX2. WRKY55 physically interacts with Arabidopsis ORA59 facilitating the expression of PDF1.2</i. Our results suggest that WRKY55 can function as a positive regulator for resistance against Pcc in Arabidopsis.

Effect of Bias Frequency on Bottom-Up SiO2 Gap-Filling Using Plasma-Enhanced Atomic Layer Deposition.

High-aspect-ratio patterns are required for next-generation three-dimensional (3D) semiconductor devices. However, it is challenging to eliminate voids and seams during gap-filling of these high-aspect-ratio patterns, such as deep trenches, especially for nanoscale high-aspect-ratio patterns. In this study, a SiO2 plasma-enhanced atomic layer deposition process incorporated with ion collision using bias power to the substrate was used for bottom-up trench gap-filling. The effect of bias power frequency on SiO2 trench gap-filling was then investigated. Results showed that changes in bias power frequency did not significantly change the process rate, such as SiO2 growth per cycle. At relatively low bias power frequencies, high-energy ions formed an overhang at the entrance of the high-aspect-ratio trench pattern through sputter etching and redeposition, blocking the pattern entrance. However, at relatively high-frequency bias power, overhang formation due to sputtering did not occur. In the trench interior, due to a scattering effect of ions, deposition was thicker at the bottom of the trench than that at the top, achieving bottom-up gap-filling and void-free gap-filling.

Effect of Cl2 Radical on Dry Development of Spin-Coated Metal Oxide Resist.

In this study, the effects of Cl2 radicals on dry development of spin-coated metal oxide resist (MOR) and changes in its surface binding states were investigated to verify the mechanism of dry development. Dry development characteristics of tin hydroxide (Tin OH), which is one of the MOR candidates for next generation lithography, were investigated as functions of process time and temperature using a Cl2 radicals source. Non-UV-exposed Tin OH film showed a linear etch rate (1.77 nm/min) from the initial thickness of ∼50 nm, while the UV-exposed film showed slower etch behavior (1.46 nm/min) in addition to the increase of film thickness for up to 3 min during the Cl2 radical dry development. UV-exposed photoresist (PR) contained more oxygen (Sn-O bonding) in the film due to the removal of butyl compounds from the clusters during the UV exposure process. Therefore, due to the lower reaction of chlorine radicals with Sn-O in the UV-exposed Tin OH than the other bindings, the non-UV-exposed PR was preferentially removed compared to the UV-exposed PR. As the temperature decreases, the overall etch rate decreases, but the difference in etch rate between exposed and unexposed Tin OH becomes larger. Finally, at a substrate temperature of -20 °C, the non-UV-exposed Tin OH with a thickness of 50 nm was completely removed, while ∼30 nm thick PR remained for UV-exposed Tin OH. Eventually, a negative tone development was possible with Cl2 radical plasma due to the difference in activation energy between the UV-exposed and non-UV-exposed films. It is believed that dry development using Cl2 radicals will be one of the most important process techniques for next-generation patterning to remove problems such as pattern leaning, line edge roughness, residue, etc., caused by wet development.

Ameliorative Effects of Flavonoids from Platycodon grandiflorus Aerial Parts on Alloxan-Induced Pancreatic Islet Damage in Zebrafish.

Platycodon grandiflorus (balloon flower), used as a food reserve as well as in traditional herbal medicine, is known for its multiple beneficial effects. In particular, this plant is widely used as a vegetable in Republic of Korea. We examined the ameliorative effects of P. grandiflorus on alloxan-induced pancreatic islet damage in zebrafish. The aerial part treatment led to a significant recovery in pancreatic islet size and glucose uptake. The efficacy of the aerial part was more potent than that of the root. Eight flavonoids (1-8) were isolated from the aerial part. Structures of two new flavone glycosides, designated dorajiside I (1) and II (2), were elucidated to be luteolin 7-O-α-L-rhamno-pyranosyl (1 → 2)-(6-O-acetyl)-ß-D-glucopyranoside and apigenin 7-O-α-L-rhamnopyranosyl (1 → 2)-(6-O-acetyl)-ß-D-glucopyranoside, respectively, by spectroscopic analysis. Compounds 1, 3, 4 and 6-8 yielded the recovery of injured pancreatic islets in zebrafish. Among them, compound 7 blocked KATP channels in pancreatic ß-cells. Furthermore, compounds 3, 4, 6 and 7 showed significant changes with respect to the mRNA expression of GCK, GCKR, GLIS3 and CDKN2B compared to alloxan-induced zebrafish. In conclusion, the aerial part of P. grandiflorus and its constituents conferred a regenerative effect on injured pancreatic islets.

The efficacy of supervised learning and semi-supervised learning in diagnosis of impacted third molar on panoramic radiographs through artificial intelligence model.

OBJECTIVES: The aim of the study was to evaluate the efficacy of traditional supervised learning (SL) and semi-supervised learning (SSL) in the classification of mandibular third molars (Mn3s) on panoramic images. The simplicity of preprocessing step and the outcome of the performance of SL and SSL were analyzed. METHODS: Total 1625 Mn3s cropped images from 1000 panoramic images were labeled for classifications of the depth of impaction (D class), spatial relation with adjacent second molar (S class), and relationship with inferior alveolar nerve canal (N class). For the SL model, WideResNet (WRN) was applicated and for the SSL model, LaplaceNet (LN) was utilized. RESULTS: In the WRN model, 300 labeled images for D and S classes, and 360 labeled images for N class were used for training and validation. In the LN model, only 40 labeled images for D, S, and N classes were used for learning. The F1 score were 0.87, 0.87, and 0.83 in WRN model, 0.84, 0.94, and 0.80 for D class, S class, and N class in the LN model, respectively. CONCLUSIONS: These results confirmed that the LN model applied as SSL, even utilizing a small number of labeled images, demonstrated the satisfactory of the prediction accuracy similar to that of the WRN model as SL.

Plasma Enhanced Atomic Layer Deposition of Silicon Nitride for Two Different Aminosilane Precursors Using Very High Frequency (162 MHz) Plasma Source.

Plasma enhanced atomic layer deposition (PEALD) of silicon nitride (SiNx) using very high frequency (VHF, 162 MHz) plasma source was investigated at the process temperatures of 100, 200, and 300 °C. Two aminosilane precursors having different numbers of amino ligands, bis(tert-butylamino)silane (BTBAS) and di(sec-butylamino)silane (DSBAS), were used as Si precursors. A comparative study was also conducted to verify the effect of the number of amino ligands on the properties of SiNx film. At all process temperatures, DSBAS, having one amino ligand, performed better than BTBAS in various aspects. SiNx films deposited using DSBAS had lower surface roughness, higher film density, lower wet etch rate, improved electrical characteristics, and higher growth rate than those deposited using BTBAS. With the combination of a VHF plasma source and DSBAS with one amino ligand, the SiNx films grown at 300 °C exhibited low wet etch rates (≤2 nm/min) in a dilute HF solution (100:1 of deionized water:HF) as well as low C content below the XPS detection limit. Also, excellent step coverage close to 100% on high aspect ratio (30:1) trench structures was obtained by using VHF plasma, which could provide sufficient flux of plasma species inside the trenches in conjunction with DSBAS having fewer amino ligands than BTBAS.

Synthesis and evaluation of ent-Conduramine C-1 derivatives as α-glucosidase inhibitors via CSI-mediated amination reaction.

Concise synthesis of ent-conduramine C-1 and its derivatives has been achieved by using commercially available d-ribose. The key steps in the synthesis are regioselective and diastereoselective amination of polybenzyl ethers by chlorosulfonyl isocyanate (CSI), chelation-controlled carbonyl addition, and intramolecular olefin metathesis. All of the synthesized compounds were evaluated for inhibitory activity against α-glucosidase. The derivatives 18 (IC50 = 0.65 ± 0.03 mM) and 19 (IC50 = 0.26 ± 0.01 mM) were identified to be more potent than well-known α-glucosidase inhibitor acarbose (IC50 = 1.05 ± 0.17 mM) as a positive control.

A resveratrol oligomer, hopeaphenol suppresses virulence activity of Pectobacterium atrosepticum via the modulation of the master regulator, FlhDC.

Pectobacterium atrosepticum (P. atrosepticum: Pba) which causes potato soft rot and blackleg is a notorious plant pathogen worldwide. Discovery of new types of antimicrobial chemicals that target specifically to virulence factors such as bacterial motility and extracellular enzymes is required for protecting crops from pathogenic infection. A transcriptomic analysis of Pba upon hopeaphenol treatment revealed that bacterial motility-related gene expression, including a master regulator flhDC genes, was significantly influenced by hopeaphenol. We further generated a double knock-out mutant of flhDC genes by CRISPR/Cas9 system and confirmed phenotypic changes in bacterial motility, transcription of extracellular enzymes, and disease development consistent with the result of wild-type treated with hopeaphenol. The hopeaphenol-treated Pba strains, wild-type, double mutant, and complemented strain were unable to secrete the enzymes in vitro, while ΔflhDC double mutant strain reduced the secretion. Thus, our study supports that FlhDC is essential for the virulence of Pba, and proposes that hopeaphenol modulates FlhDC-dependent virulence pathways, suggesting a potential of hopeaphenol as an anti-virulence agent to manage potato soft rot and blackleg diseases.

Resveratrol Oligomers, Plant-Produced Natural Products With Anti-virulence and Plant Immune-Priming Roles.

Antibiotic resistance has become increasingly prevalent in the environment. Many alternative strategies have been proposed for the treatment and prevention of diverse diseases in agriculture. Among them, the modulation of bacterial virulence to bypass antibiotic resistance or boost plant innate immunity can be considered a promising drug target. Plant-produced natural products offer a broad spectrum of stereochemistry and a wide range of pharmacophores, providing a great diversity of biological activities. Here, we present a perspective on the putative role of plant-produced resveratrol oligomers as anti-virulence and plant-immune priming agents for efficient disease management. Resveratrol oligomers can decrease (1) bacterial motility directly and (2) indirectly by attenuating the bacterial type III secretion system (TT3S). They induce enhanced local immune responses mediated by two-layered plant innate immunity, demonstrating (3) a putative plant immune priming role.

Deposition of Very-Low-Hydrogen-Containing Silicon at a Low Temperature Using Very-High-Frequency (162 MHz) SiH4 Plasma.

Low-hydrogen-containing amorphous silicon (a-Si) was deposited at a low temperature of 80 °C using a very high frequency (VHF at 162 MHz) plasma system with multi-split electrodes. Using the 162 MHz VHF plasma system, a high deposition rate of a-Si with a relatively high deposition uniformity of 6.7% could be obtained due to the formation of high-ion-density (>1011 cm-3) plasma with SiH4 and a lack of standing waves by using small multi-split electrodes. The increase in the radio frequency (RF) power decreased the hydrogen content in the deposited silicon film and, at a high RF power of 2000 W, a-Si with a low hydrogen content of 3.78% could be deposited without the need for a dehydrogenation process. The crystallization of the a-Si by ultraviolet (UV) irradiation showed that the a-Si can be crystallized with a crystallinity of 0.8 and a UV energy of 80 J without dehydrogenation. High-resolution transmission electron microscopy showed that the a-Si deposited by the VHF plasma was a very small nanocrystalline-like a-Si and the crystalline size significantly grew with the UV irradiation. We believe that the VHF (162 MHz) multi-split plasma system can be used for a low-cost low-temperature polysilicon (LTPS) process.