p-Type polymer-hybridized high-performance piezoelectric nanogenerators.

Enhancing the output power of a nanogenerator is essential in applications as a sustainable power source for wireless sensors and microelectronics. We report here a novel approach that greatly enhances piezoelectric power generation by introducing a p-type polymer layer on a piezoelectric semiconducting thin film. Holes at the film surface greatly reduce the piezoelectric potential screening effect caused by free electrons in a piezoelectric semiconducting material. Furthermore, additional carriers from a conducting polymer and a shift in the Fermi level help in increasing the power output. Poly(3-hexylthiophene) (P3HT) was used as a p-type polymer on piezoelectric semiconducting zinc oxide (ZnO) thin film, and phenyl-C(61)-butyric acid methyl ester (PCBM) was added to P3HT to improve carrier transport. The ZnO/P3HT:PCBM-assembled piezoelectric power generator demonstrated 18-fold enhancement in the output voltage and tripled the current, relative to a power generator with ZnO only at a strain of 0.068%. The overall output power density exceeded 0.88 W/cm(3), and the average power conversion efficiency was up to 18%. This high power generation enabled red, green, and blue light-emitting diodes to turn on after only tens of times bending the generator. This approach offers a breakthrough in realizing a high-performance flexible piezoelectric energy harvester for self-powered electronics.

Inverted organic solar cells with ZnO nanowalls prepared using wet chemical etching in a KOH solution.

We report on the photovoltaic (PV) performances of inverted organic solar cells (IOSCs) that were fabricated from PCBM:P3HT polymer with a ZnO thin film and ZnO nanowalls as electron transport and hole block layers. ZnO thin film on ITO/glass substrate was deposited using a simply aqueous solution route. ZnO nanowall structures were obtained via wet chemical etching of ZnO thin films in a KOH solution. The power conversion efficiency (PCE) of the IOSC with ZnO nanowalls was significantly improved by 44% from 1.254% to 1.811% compared to that of the IOSC with ZnO thin film. The short circuit current in IOSCs fabricated with the ZnO nanowalls was increased mainly due to the increase in the charge transport interface area, as a result of enhancement in the PCE. This work suggests a method for fabricating efficient PV devices with a larger charge transport area for future prospects.

Effect of zymosan and poly (I:C) adjuvants on responses to microneedle immunization coated with whole inactivated influenza vaccine.

Microneedles are the micrometer size devices used for the delivery of vaccines and biotherapeutics. In order to increase the vaccine efficacy and reduce the antigen dose, there is a significant need to find some adjuvants for the microneedle vaccination. In this study, zymosan, which is the cell wall preparation of Saccharomyces cerevisiae, or poly (I:C) was coated on a microneedle with inactivated influenza virus, and then immunized into BALB/c mouse to determine the immunogenicity, protection and synergetic effect between two adjuvants. As a result, the group administered with zymosan and vaccine antigen showed significantly stronger IgG response, HI titer and IgG subtypes without any adverse effects, compared to the group immunized with the vaccine antigen alone. Also, there were enhanced cellular immune responses in the group received adjuvant with vaccine antigen. In addition, they showed superior protection and lung viral reduction against lethal viral challenge. Taken together, this study confirms that zymosan can be used as an immunostimulant for microneedle vaccination.

A novel electroporation system for efficient molecular delivery into Chlamydomonas reinhardtii with a 3-dimensional microelectrode.

Electroporation is one of the most widely used transfection methods because of its high efficiency and convenience among the various transfection methods. Previous micro-electroporation systems have some drawbacks such as limitations in height and design, time-consuming and an expensive fabrication process due to technical constraints. This study fabricates a three dimensional microelectrode using the 3D printing technique. The interdigitated microstructure consisting of poly lactic acid was injected by a 3D printer and coated with silver and aluminum with a series of dip-coatings. With the same strength of electric field (V cm(-1)), a higher efficiency for molecular delivery and a higher cellular viability are achieved with the microelectrode than with a standard cuvette. In addition, this study investigates chemicophysical changes such as Joule heating and dissolved metal during electroporation and showed the micro-electroporation system had less chemicophysical changes. It was concluded that the proposed micro-electroporation system will contribute to genetic engineering as a promising delivery tool, and this combination of 3D printing and electroporation has many potential applications for diverse designs or systems.

Piezoelectric two-dimensional nanosheets/anionic layer heterojunction for efficient direct current power generation.

Direct current (DC) piezoelectric power generator is promising for the miniaturization of a power package and self-powering of nanorobots and body-implanted devices. Hence, we report the first use of two-dimensional (2D) zinc oxide (ZnO) nanostructure and an anionic nanoclay layer to generate piezoelectric DC output power. The device, made from 2D nanosheets and an anionic nanoclay layer heterojunction, has potential to be the smallest size power package, and could be used to charge wireless nano/micro scale systems without the use of rectifier circuits to convert alternating current into DC to store the generated power. The combined effect of buckling behaviour of the ZnO nanosheets, a self-formed anionic nanoclay layer, and coupled semiconducting and piezoelectric properties of ZnO nanosheets contributes to efficient DC power generation. The networked ZnO nanosheets proved to be structurally stable under huge external mechanical loads.