RESUMEN
In this study, we investigated the effect of the stacking order of metal precursors on the formation of volume defects, such as blisters and nanopores, in CZTSSe thin-film solar cells. We fabricated CZTSSe thin films using three types of metal-precursor combinations, namely, Zn/Cu/Sn/Mo, Cu/Zn/Sn/Mo, and Sn/Cu/Zn/Mo, and studied the blister formation. The blister-formation mechanism was based on the delamination model, taking into consideration the compressive stress and adhesion properties. A compressive stress could be induced during the preferential formation of a ZnSSe shell. Under this stress, the adhesion between the ZnSSe film and the Mo substrate could be maintained by the surface tension of a metallic liquid phase with good wettability, or by the functioning of ZnSSe pillars as anchors, depending on the type of metal precursor used. Additionally, the nanopore formation near the back-contact side was found to be induced by the columnar microstructure of the metal precursor with the Cu/Zn/Mo stacking order and its dezincification. Based on the two volume-defect-formation mechanisms proposed herein, further development of volume-defect-formation suppression technology is expected to be made.
RESUMEN
In this study, to control the formation of non-uniformly distributed large voids and Cu-Sn alloy agglomeration, which leads to local compositional misfit and secondary phase formation, a SnS compound precursor was applied instead of metal Sn to avoid compositional non-uniformity. Using a Cu/Zn/SnS stacked precursor, a temperature tracking experiment was conducted to confirm the formation controllability of the void and the secondary phase. According to the results of this temperature-profile tracking experiment, it was confirmed that the large void was successfully controlled; however, an additional ZnSSe secondary phase layer was formed in the middle of the CZTSSe upper layer and small voids were distributed relatively uniformly in the bottom CZTSSe layer. An efficiency of approximately 8% was obtained when the Cu/Zn/SnS stacked precursor was used. The origins of the low short-circuit current and fill factor are posited to be caused by the increase of the energy bandgap of the CZTSSe layer due to the SnS precursor, the thin top CZTSSe layer (around 600 nm) of the triple CZTSSe layer, and the diffusion length extension of the minor carriers caused by bypassing the ZnSSe phase.
RESUMEN
In this study, a 5-nm thick Al2O3 layer was patterned onto the Mo electrode in the form of a dot to produce a local rear contact, which looked at the effects of this contact structure on Cu2ZnSn(S1-xSex)4 (CZTSSe) growth and solar cell devices. Mo was partially exposed through open holes having a square dot shape, and the closed-ratios of Al2O3 passivated areas were 56%, 75%, and 84%. The process of synthesizing CZTSSe is the same as that of the previous process showing 12.62% efficiency. When the 5-nm-Al2O3 dot patterning was applied to the Mo surface, we observed that the MoSSe formation was well suppressed under the area coated of 5-nm-Al2O3 film. The self-alignment phenomenon was observed in the back-contact area. CZTSSe was easily formed in the Mo-exposed area, while voids were formed near the Al2O3-coated area. The efficiency of the CZTSSe solar cell decreased when the Al2O3 passivated area increased. The exposure area and pitch of Mo, the collecting path of the hole, and the supplying path of Na seemed to be related to efficiency. Thus, it was suggested that the optimization of the Mo-exposed pattern and the additional Na supply are necessary to develop the optimum self-aligned CZTSSe light absorber.
RESUMEN
Recently, highly efficient CZTS solar cells using pure metal precursors have been reported, and our group created a cell with 12.6% efficiency, which is equivalent to the long-lasting world record of IBM. In this study, we report a new secondary phase formation mechanism in the back contact interface. Previously, CZTSSe decomposition with Mo has been proposed to explain the secondary phase and void formation in the Mo-back contact region. In our sulfo-selenization system, the formation of voids and secondary phases is well explained by the unique wetting properties of Mo and the liquid metal above the peritectic reaction (η-Cu6Sn5 â ε-Cu3Sn + liquid Sn) temperature. Good wetting between the liquid Sn and the Mo substrate was observed because of strong metallic bonding between the liquid metal and Mo layer. Thus, some ε-Cu3Sn and liquid Sn likely remained on the Mo layer during the sulfo-selenization process, and Cu-SSe and Cu-Sn-SSe phases formed on the Mo side. When bare soda lime glass (SLG) was used as a substrate, nonwetting adhesion was observed because of weak van der Walls interactions between the liquid metal and substrate. The Cu-Sn alloy did not remain on the SLG surface, and Cu-SSe and Cu-Sn-SSe phases were not observed after the final sulfo-selenization process. Additionally, Mo/SLG substrates coated with a thin Al2O3 layer (1-5 nm) were used to control secondary phase formation by changing the wetting properties between Mo and the liquid metal. A 1 nm Al2O3 layer was enough to control secondary phase formation at the CZTSSe/Mo and void/Mo interfaces, and a 2 nm Al2O3 layer was enough to perfectly control secondary phase formation at the Mo interface and Mo-SSe formation.
RESUMEN
For kesterite copper zinc tin sulfide/selenide (CZTSSe) solar cells to enter the market, in addition to efficiency improvements, the technological capability to produce flexible and large-area modules with homogeneous properties is necessary. Here, we report a greater than 10% efficiency for a cell area of approximately 0.5 cm2 and a greater than 8% efficiency for a cell area larger than 2 cm2 of certified flexible CZTSSe solar cells. By designing a thin and multi-layered precursor structure, the formation of defects and defect clusters, particularly tin-related donor defects, is controlled, and the open circuit voltage value is enhanced. Using statistical analysis, we verify that the cell-to-cell and within-cell uniformity characteristics are improved. This study reports the highest efficiency so far for flexible CZTSSe solar cells with small and large areas. These results also present methods for improving the efficiency and enlarging the cell area.
Asunto(s)
Metales/química , Energía Solar , Espectrometría por Rayos XRESUMEN
Amongst several processes which have been developed for the production of reliable chalcopyrite Cu(InGa)Se2 photovoltaic absorbers, the 2-step metallization-selenization process is widely accepted as being suitable for industrial-scale application. Here we visualize the detailed thermal behavior and reaction pathways of constituent elements during commercially attractive rapid thermal processing of glass/Mo/CuGa/In/Se precursors on the basis of the results of systematic characterization of samples obtained from a series of quenching experiments with set-temperatures between 25 and 550 °C. It was confirmed that the Se layer crystallized and then melted between 250 and 350 °C, completely disappearing at 500 °C. The formation of CuInSe2 and Cu(InGa)Se2 was initiated at around 450 °C and 550 °C, respectively. It is suggested that pre-heat treatment to control crystallization of Se layer should be designed at 250-350 °C and Cu(InGa)Se2 formation from CuGa/In/Se precursors can be completed within a timeframe of 6 min.