RESUMEN
Results from studying the effect of an applied electric voltage on the Raman spectrum of graphene deposited on a lithium niobate crystal substrate with a ferroelectric domain structure are presented. The use of the principal component method for data processing in combination with correlation analysis made it possible to reveal the contribution to the change in the spectra associated with the linear deformation of the substrate due to the inverse piezoelectric effect. An effect of the graphene coating peeling was found. Furthermore, bending deformations of the graphene coating associated with the presence of a relief on the substrate were found. An analysis of the change in the spectra of graphene under the application of an electric voltage made it possible to determine the height of this relief.
RESUMEN
The process of acoustically stimulated charge transport in the graphene film on the surface of the YZ-cut of a LiNbO3 crystal was investigated. It was found that the dependence of the current in the graphene film on the frequency of the surface acoustic wave (SAW) excitation repeats the amplitude-frequency response of the SAW delay time line. It is shown that increasing the SAW amplitude leads to an increase in the current in the graphene film, and the current in the graphene film depends linearly on the amplitude of the high-frequency input signal supplied to the interdigital transducer (IDT, in dB). It is demonstrated that at a positive bias potential on the graphene film, the SAW propagation allows to change the direction of the current in the graphene film by changing the amplitude of the SAW. It is also shown that in the frequency range of the amplitude-frequency response of the SAW delay time line, the current in the graphene film can vary from positive to negative values depending on the frequency. The capability to control the SAW excitation frequency or the SAW amplitude makes it possible to control the value and direction of the current in the graphene film. The SAW propagation lets to collect and transport the photo-stimulated charges in the graphene film on the crystal surface.
RESUMEN
Among the different graphene derivatives, graphene oxide is the most intensively studied material as it exhibits reliable and repeatable resistive switching. The operative mechanisms that are responsible for resistive switching are being intensively investigated, and three models explaining the change in the resistive states have been developed. These models are grounded in the metallic-like filamentary conduction, contact resistance modification and the oxidation of/reduction in the graphene oxide bulk. In this work, using Al/GO/n-Si structures, we demonstrate that all three of these operative mechanisms can simultaneously participate in the resistive switching of graphene oxide. Multiple point-like conduction channels in the graphene oxide films were detected by the electron beam-induced current (EBIC) technique. At the same time, large areas with increased conductivity were also revealed by EBIC. An analysis of these areas by Raman spectroscopy indicates the change in the graphene oxide bulk's resistive properties. The EBIC data along with the measurements of the capacitance-voltage characteristics provided strong evidence of the involvement of an aluminum/graphene oxide interface in the switching processes. In addition, by using Al/GO/n-Si structures, we were able to identify unique local properties of the formed conductive channels, namely the change of the charge state of a conductive channel due to the creation of negatively charged traps and/or an increase in the GO work function.
RESUMEN
The high salt-bearing liquid radioactive waste (evaporator bottoms, EB) makes up the most voluminous NPP waste and needs solidification. In the paper presented, we introduce a novel formation process study of the struvite-based phosphate matrices ((K, NH4)MgPO4·6H2O) and the developed phosphate matrix compositions for the solidification of high salt-bearing solutions. The solutions simulate the EB of nuclear power plants with pressurized water reactors (NPP PWR). The effect of the EB's composition and salt content on the matrices' mechanical strength was investigated. The cesium-selective nickel-potassium ferrocyanide sorbent or 10-20% of MgO over the reaction stoichiometry, introduced at the matrix synthesis stage, allowed the production of matrices with the average 137Сs leach rate of less than 10-3 g cm-2 day-1 and the mechanical strength over 5 MPa. The matrices obtained completely satisfied the cemented radioactive waste requirements and contained up to 17-17.5 wt% of salts, which was 1.7-2.5 times higher compared to the Portland cement-based matrices.
Asunto(s)
Residuos Radiactivos , Materiales de Construcción , Fosfatos , Cloruro de Sodio , EstruvitaRESUMEN
Because of their unique atomic structure, 2D materials are able to create an up-to-date paradigm in fundamental science and technology on the way to engineering the band structure and electronic properties of materials on the nanoscale. One of the simplest methods along this path is the superposition of several 2D nanomaterials while simultaneously specifying the twist angle between adjacent layers (θ), which leads to the emergence of Moiré superlattices. The key challenge in 2D nanoelectronics is to obtain a nanomaterial with numerous Moiré superlattices in addition to a high carrier mobility in a stable and easy-to-fabricate material. Here, we demonstrate the possibility of synthesizing twisted multilayer graphene (tMLG) with a number of monolayers NL = 40-250 and predefined narrow ranges of θ = 3-8°, θ = 11-15°, and θ = 26-30°. A 2D nature of the electron transport is observed in the tMLG, and its carrier mobilities are close to those of twisted bilayer graphene (tBLG) (with θ = 30°) between h-BN layers. We demonstrate an undoubtful presence of numerous Moiré superlattices simultaneously throughout the entire tMLG thickness, while the periods of these superlattices are rather close to each other. This offers a challenge of producing a next generation of devices for nanoelectronics, twistronics, and neuromorphic computing for large data applications.
RESUMEN
Magnetic levitational bioassembly of three-dimensional (3D) tissue constructs represents a rapidly emerging scaffold- and label-free approach and alternative conceptual advance in tissue engineering. The magnetic bioassembler has been designed, developed, and certified for life space research. To the best of our knowledge, 3D tissue constructs have been biofabricated for the first time in space under microgravity from tissue spheroids consisting of human chondrocytes. Bioassembly and sequential tissue spheroid fusion presented a good agreement with developed predictive mathematical models and computer simulations. Tissue constructs demonstrated good viability and advanced stages of tissue spheroid fusion process. Thus, our data strongly suggest that scaffold-free formative biofabrication using magnetic fields is a feasible alternative to traditional scaffold-based approaches, hinting a new perspective avenue of research that could significantly advance tissue engineering. Magnetic levitational bioassembly in space can also advance space life science and space regenerative medicine.
RESUMEN
Extraordinary Hall effect probes with 160 nm × 160 nm working area were fabricated using photo- and electron-beam lithographic procedures with the aim of direct measurements of MFM cantilever tip magnetic properties. The magnetic field sensitivity of the probes was 35 Ω T(-1). Magnetic induction of the MFM cantilever tips coated by Co and SmCo films was measured with the probes. It was shown that the resolution of the probes was of the order of 10 nm.