In Situ Generation of Pseudorutile Oxide as the Cathode for Direct Electrolysis of CO2.

The conversion of CO2 into CO in high-temperature solid oxide electrolysis cells (SOECs) is an attractive route for the CO2 utilization using the intermittent renewables. The low-cost and highly catalytic cathode is important for the direct electrolysis of pure CO2. In this study, non-perovskite Fe0.5Mg0.25+0.5xTi0.25-0.5xNb1-xMoxO4 oxides (denoted as Mo-x when x is equal to 0, 0.1, and 0.2) are evaluated as the cathode of an SOEC for the direct electrolysis of CO2. Mo6+ doping converted the wolframite Mo-0 into an α-PbO2-type with cation disordering, while further doping to Mo-0.2 showed a wolframite with cation ordering again. The SOEC with Mo-0.2 as the cathode exhibits the best electrochemical performance for the direct electrolysis of CO2 as a large portion of the oxide converted into oxygen-deficient pseudorutile-type oxide with a nominal formula of M5O9 (M = cation). The pseudorutile, a crystallographic shear phase of rutile, can be obtained after 60 h of direct electrolysis in CO2 at a 1.3 V bias rather than a reduction under 5% H2. The SOEC with Mo-0.2 as the cathode imparted a stable current density of 0.45 A cm-2, which could be related to the production of pseudorutile decorated with nanoparticles of MoO2. These results show that molybdenum doping is an effective strategy for developing oxygen-deficient rutile (pseudorutile) for the electrolysis of CO2.

Spatiotemporal characteristics of air pollution in Chengdu-Chongqing urban agglomeration (CCUA) in Southwest, China: 2015-2021.

Studying the spatiotemporal characteristics of air pollutants in urban agglomerations and their response factors will help to improve the quality of urban living. In combining air quality monitoring data and wavelet analysis from the Chengdu-Chongqing urban agglomeration (CCUA), this study assessed the spatiotemporal distribution characteristics and influential factors of air pollutants on daily, monthly and annual scales. The results showed that the concentration of air pollutants in the CCUA has decreased year by year, and air quality has improved. Except for O3, pollutants in autumn and winter were higher than those in summer. The spatial distribution of air pollutants was obvious distributed in Chengdu, Chongqing, Zigong and Dazhou. Pollution incidents were mainly concentrated in winter. The 6 air pollutants and air quality index (AQI) have dominant periods on multiple time scales. AQI showed positive coherence with PM2.5 and PM10 on multiple time scales, and obvious positive coherence with SO2, CO, NO2 and O3 in the short term scale. AQI was not strongly correlated with the fire point, but exhibited obvious negative coherence in the long term scale. In addition, AQI showed an obvious positive correlation with temperature and sunshine hours in short term, and a clear negative correlation with humidity and rainfall. The research results of this paper will provide a reference for pollution prevention and control in the CCUA.

Crops' response to the emergent air pollutants.

MAIN CONCLUSION: Consequences of air pollutants on physiology, biology, yield and quality in the crops are evident. Crop and soil management can play significant roles in attenuating the impacts of air pollutants. With rapid urbanization and industrialization, air pollution has emerged as a serious threat to quality crop production. Assessing the effect of the elevated level of pollutants on the performance of the crops is crucial. Compared to the soil and water pollutants, the air pollutants spread more rapidly to the extensive area. This paper has reviewed and highlighted the major findings of the previous research works on the morphological, physiological and biochemical changes in some important crops and fruits exposed to the increasing levels of air pollutants. The crop, soil and environmental factors governing the effect of air pollutants have been discussed. The majority of the observations suggest that the air pollutants alter the physiology and biochemical in the plants, i.e., while some pollutants are beneficial to the growth and yields and modify physiological and morphological processes, most of them appeared to be detrimental to the crop yields and their quality. A better understanding of the mechanisms of the uptake of air pollutants and crop responses is quite important for devising the measures ‒ at both policy and program levels ‒ to minimize their possible negative impacts on crops. Further research directions in this field have also been presented.

Investigating the effect of copper and magnesium ions on nitrogen removal capacity of pure cultures by modified non-competitive inhibition model.

Copper, a common heavy metal, may be beneficial for or poisonous to microbial activity. The objective of this study was to determine the effect of different copper ion concentrations on the nitrogen removal performance of Arthrobacter arilaitensis strain Y-10 and Pseudomonas taiwanensis strain J488. The non-competitive inhibition model was employed to evaluate the 50% inhibition concentrations (IC50 values) of copper ions toward the pure strains. In the absence of magnesium ions, a low concentration of copper (0.1 mg/L) significantly enhanced the ammonium removal ability of strain Y-10 and its removal efficiency increased by 10.88% compared with the control treatment. Copper ranging from 0 to 0.1 mg/L had no significant effect on the ammonium removal capacity of strain J488. After adding 9.90 mg/L of magnesium to the basal medium, the effects of copper on nitrification of ammonium or denitrification of nitrate or nitrite were also assessed. In these conditions, 0.25 mg/L copper ions could strongly inhibit the ammonium, nitrate and nitrite removal activities for strain Y-10. For strain J488, no clear deterioration in ammonium removal efficiency was observed at copper ion concentrations below 0.5 mg/L, but 0.25 mg/L copper ions significantly inhibited nitrate and nitrite removal efficiencies, which were only 45.88% and 6.35%, respectively. The IC50 values of copper ions for nitrate and nitrite removal by strain Y-10 were 0.195 and 0.090 mg/L respectively; for strain J488, the IC50 values were 0.175 and 0.196 mg/L. The magnesium ions could improve the cell growth, nitrogen removal efficiency and copper ion resistance of bacteria.

Simultaneous nitrification and denitrification with different mixed nitrogen loads by a hypothermia aerobic bacterium.

Microorganism with simultaneous nitrification and denitrification ability plays a significant role in nitrogen removal process, especially in the eutrophic waters with excessive nitrogen loads. The nitrogen removal capacity of microorganism may suffer from low temperature or nitrite nitrogen source. In this study, a hypothermia aerobic nitrite-denitrifying bacterium, Pseudomonas tolaasii strain Y-11, was selected to determine the simultaneous nitrification and denitrification ability with mixed nitrogen source at 15 °C. The sole nitrogen removal efficiencies of strain Y-11 in simulated wastewater were obtained. After 24 h of incubation at 15 °C, the ammonium nitrogen fell below the detection limit from an initial value of 10.99 mg/L. Approximately 88.0 ± 0.33% of nitrate nitrogen was removed with the initial concentration of 11.78 mg/L and the nitrite nitrogen was not detected with the initial concentration of 10.75 mg/L after 48 h of incubation at 15 °C. Additionally, the simultaneous nitrification and denitrification nitrogen removal ability of P. tolaasii strain Y-11 was evaluated using low concentration of mixed NH4+-N and NO3--N/NO2--N (about 5 mg/L-N each) and high concentration of mixed NH4+-N and NO3--N/NO2--N (about 100 mg/L-N each). There was no nitrite nitrogen accumulation at the time of evaluation. The results demonstrated that P. tolaasii strain Y-11 had higher simultaneous nitrification and denitrification capacity with low concentration of mixed inorganic nitrogen sources and may be applied in low temperature wastewater treatment.

Spatial and temporal variations in non-point source losses of nitrogen and phosphorus in a small agricultural catchment in the Three Gorges Region.

Losses of agricultural pollutants from small catchments are a major issue for water quality in the Three Gorges Region. Solutions are urgently needed. However, before pollutant losses can be controlled, information about spatial and temporal variations in pollutant losses is needed. The study was carried out in the Wangjiagou catchment, a small agricultural catchment in Fuling District, Chongqing, and the data about non-point source losses of nitrogen and phosphorus was collected here. Water samples were collected daily by an automatic water sampler at the outlets of two subcatchments from 2012 to 2014. Also, samples of surface runoff from 28 sampling sites distributed through the subcatchments were collected during 12 rainfall events in 2014. A range of water quality variables were analyzed for all samples and were used to demonstrate the variation in non-point losses of nitrogen and phosphorus over a range of temporal and spatial scales and in different types of rainfall in the catchment. Results showed that there was a significant linear correlation between the mass concentrations of total nitrogen (TN) and nitrate (NO3-N) in surface runoff and that the relationship was maintained with changes in time. Concentrations of TN and NO3-N peaked after fertilizer was applied to crops in spring and autumn; concentrations decreased rapidly after the peak values in spring but declined slowly in autumn. N and P concentrations fluctuated more and showed a greater degree of dispersion during the spring crop cultivation period than those in autumn. Concentrations of TN and NO3-N in surface runoff were significantly and positively correlated with the proportion of the area that was planted with corn and mustard tubers, but were negatively correlated with the proportion of the area taken up with rice and mulberry plantations. The average concentrations of TN and NO3-N in surface runoff reached the highest level from the sampling points at the bottom of the land used for corn only, but lowest in rice fields. Slope gradient had a significant positive correlation with TN's and total phosphorus (TP)'s concentration losses. Concentrations of TN, NO3-N, and total phosphorus were significantly correlated with rainfall. Peak concentrations of ammoniacal nitrogen occurred during the fertilizer application period in spring and autumn. Different structures of land use types had a significant influence on the concentration losses of nitrogen and phosphorus; thus, using a reasonable way to adjust land use structure and spatial arrangement of whole catchment was an effective solution to control non-point source pollution of the Three Gorges Region.

Rutile-Type Co0.5Ti0.5NbO4-Based Cathode with In Situ Exsolved Metal Particles for Direct CO2 Electrolysis.

Rutile-type Co0.5Ti0.5NbO4 (CTO)-based materials doped with Fe3+ or Ni2+ were investigated as cathode electrodes to modify their electrical conductivity and electrocatalysis toward CO2 splitting. Higher electric conductivity was found in Co0.4Fe0.2Ti0.4NbO4 (CTO-Fe, 0.78 S cm-1) and Co0.25Ni0.25Ti0.5NbO4 (CTO-Ni, 2.10 S cm-1) compared to CTO (0.49 S cm-1) after the reduction at 800 °C in Ar-5% H2. Co and Co-Ni particles exsolved in situ from the surface of CTO, CTO-Fe, and CTO-Ni after reduction. CTO-Ni and CTO-Fe cathodes did better in the CO2 electrolysis at 800 °C than the CTO one, but the CTO-Ni cell was unstable after 10 h of operation due to the carbon deposition that blocked the electrode. The cell with CTO-Fe demonstrated a good stability for CO2 splitting in 100 h. This work demonstrates that rutile-type CTO-based cathodes are promising to provide an efficient and candidate oxide cathode for the electrolysis of CO2.

Ambient plasma treatment of pectin in aqueous solution to produce a polymer used in packaging.

Water resistance, mechanical behavior and coloration of pectin needs to be tuned for packing utilization. Plasma was used for the treatment of natural products, but there is no research on its effect on the biomass in the presence of ammonia. Though the reaction of pectin (PE) and ammonia was known to impart the ammonolysis and de-esterification, the plasma treatment on PE solution containing ammonia was explored to exemplify the amination and polymerization of the carbohydrate at the ambient condition. The plasma treatment increased the coloration of the solution due to the deprotonation of PE for the production of more sp2 carbon. The film from the amination of PE showed higher hydrophobicity and water stability than the bare PE. The plasma treatment alone decreased the Young's modulus (4.3 MPa versus 22 MPa), while the nitrogen addition enhanced the Young's modulus to 160 MPa and increased the tensile strength (28.7 MPa versus 25.8 MPa of PE). The hydrogen bonds from the amine group induced a glass-to-rubber transition at 77.9 °C by the increasing the crosslinking. This work provided a facile way of aminating and conjugating the biomass in solution to produce polymer with improved mechanical properties using plasma and ammonia incorporation.

NOx precipitation and valorization driven by photocatalysis and adsorption over red soil.

Nitrogen oxides (NOx) emissions can cause air pollution that is harmful to human health, even producing serious ecological problems. Whether it is diluted in the air or not, the management and valorization of NOx from industrial emissions have been constrained by technology and finance. This study shows that red soil can be used as a photocatalyst to convert NOx into soil nitrate nitrogen (NO3--N) in the soil. The addition of zinc oxide (ZnO) and titanium dioxide (TiO2) onto the soil surface improves the photocatalytic precipitation efficiency of 1 ppm NO, approaching a removal efficiency of 77 % under ultraviolet (UV) light. The efficiency of red soil in precipitating NOx through adsorption exceeded that of photocatalysis at 100 ppm NOx (e.g. 16.02 % versus 7.70 % in 0.1-mm soil). Pot experiment reveals that the precipitated NO3--N promoted biomass of water spinach (Ipomoea aquatica Forsk). Additionally, adding ZnO or TiO2 also affects mineral nutrition. This demonstration of converting air pollutants into available nitrogen (N) for plant growth not only provides a new perspective on treatment and valorization for NOx but also sheds light on the transport of N in the air-soil-plant path.

Pr-Doped SrTi0.5Mn0.5O3-δ as an Electrode Material for a Quasi-Symmetrical Solid Oxide Fuel Cell Using Methane and Propane Fuel.

The use of identical electrodes for both the cathode and the anode in a symmetrical solid oxide fuel cell (SSOFC) can simplify the preparation process and increase the durability of the cell, but it is also demanding on the properties of the electrode including stability, electric conductivity, and electrocatalysis. The doping of variable-valence Mn4+/3+2+ on the B site of stable SrTiO3 is explored in this study as both the cathode and the anode for an SSOFC. Though the limit of Mn doping in SrTiO3 is generally low, the additional Pr3+/4+ donor on the Sr site of SrTi0.5Mn0.5O3 was found to enhance the structure stability, electric conductivity, and electrocatalysis. The cell with Pr0.5Sr0.5Ti0.5Mn0.5O3 electrodes excels under H2, propane, or CH4/H2 fuel, providing the cocatalyst was infiltrated on the anode side. The polarization resistance value of Pr0.5Sr0.5Ti0.5Mn0.5O3 was 0.27 Ω·cm2 as the cathode and 0.33 Ω·cm2 for the SSOFC using H2 fuel. The performance under CH4/H2 fuel can be boosted to above 0.9 W cm-2 if Ni/ceria was loaded onto the anode to enhance the methane reforming. This work contributes to a perovskite anode with high Mn doping in SrTiO3 for application in SSOFC for natural gas with renewable H2 injection.

Br vacancy engineering in Cs3Bi2Br9 for photocatalytic NO oxidation under visible light.

Photocatalysis using the visible light of the sun is an environmentally friendly method of eliminating the NOx pollutant from the ambient air. Although Cs3Bi2Br9, a semiconductor with a band gap of 2.54 eV, may be a strong absorber of visible light, its photocatalysis towards the abatement of NOx is unknown. In this study, Cs3Bi2-xPbxBr9-x (0 ≤ x ≤ 0.0789) are used for the photocatalytic oxidation of NOx. A significant NO oxidation efficiency (80%) is observed over Cs3Bi2-xPbxBr9-x (x = 0.0443) under visible light, which is attributable to the Br vacancy (VBr) brought about by Pb2+ doping. The presence of VBr increased the ionic selectivity of in the oxidized NO. At higher Pb doping level, two HONOs adsorbed on the VBr, linked, and then reduced by hot electrons to produce N2O22-. The di-azo coupling could passivate the activation of NO on the VBr. This work advances the defect engineering of halide for the photo-driving solid-gas reaction in air.

Output characteristics and driving factors of non-point source nitrogen (N) and phosphorus (P) in the Three Gorges reservoir area (TGRA) based on migration process: 1995-2020.

Although physical models at present have made important achievements in the assessment of non-point source pollution (NPSP), the requirement for large volumes of data and their accuracy limit their application. Therefore, constructing a scientific evaluation model of NPS nitrogen (N) and phosphorus (P) output is of great significance for the identification of N and P sources as well as pollution prevention and control in the basin. We considered runoff, leaching and landscape interception conditions, and constructed an input-migration-output (IMO) model based on the classic export coefficient model (ECM), and identified the main driving factors of NPSP using geographical detector (GD) in Three Gorges Reservoir area (TGRA). The results showed that, compared with the traditional export coefficient model, the prediction accuracy of the improved model for total nitrogen (TN) and total phosphorus (TP) increased by 15.46 % and 20.17 % respectively, and the error rates with the measured data were 9.43 % and 10.62 %. It was found that the total input volume of TN in the TGRA had declined from 58.16 × 104 t to 48.37 × 104 t, while the TP input volume increased from 2.76 × 104 t to 4.11 × 104 t, and then decreased to 4.01 × 104 t. In addition Pengxi River, Huangjin River and the northern part of Qi River were high value areas of NPSP input and output, but the range of high value areas of migration factors has narrowed. Pig breeding, rural population and dry land area were the main driving factors of N and P export. The IMO model can effectively improve prediction accuracy, and has significant implications for the prevention and control of NPSP.

Crystal-facet and microstructure engineering in ZnO for photocatalytic NO oxidation.

Photocatalysis is believed to be an important way of reducing NO pollutant in air and the facet engineering of semiconducting oxides could enhance the efficiency of the photocatalysis. ZnO nanoparticles with different exposed crystalline facets were successfully synthesized using a hydrothermal method and their photocatalytic degradation towards NO was investigated. The crystals from ZnCl2 precursor were hexagonal mesoporous ones with exposed (0002) facet, while those from zinc acetate were in the form of flakes or wheat ears with enhanced exposure of (101(-)1) facet. Calcination in air imparted an enhanced the textural coefficient of the orientated facets as well as the oxygen defects. The nanocrystals with enhanced (0002) facet and lower flat-band energy did better in photoelectrochemical water-oxidation than those with exposed (101(-)1) facet that showed superior photocatalytic activity (approaching 76.7 ± 0.6% under 365 nm photons) for NO oxidation. According to theoretical calculations, (101(-)1) facet with O termination showed much higher affinity to NO molecules than other configurations, and the oxygen vacancy in ZnO played an minor role in the photocatalytic oxidation of NO. A high quantum efficiency approaching 97.5 ± 1.4% under 275 nm photons was obtained for the ZnO crystals from zinc acetate with mixed (0002) and (101(-)1) facets. This research explores the special characteristics of ZnO with different exposed facets and is important for the future design of highly efficient photocatalyst for hazardous material removal.

Enhanced perfluorooctane acid mineralization by electrochemical oxidation using Ti3+ self-doping TiO2 nanotube arrays anode.

Perfluorooctanoic acid (PFOA) is of increasing concern due to its worldwide application and extremely environmental persistence. Herein, we demonstrated the electrochemical degradation of PFOA with high efficiency using the Ti3+ self-doping TiO2 nanotube arrays (Ti3+/TiO2-NTA) anode. The fabricated Ti3+/TiO2-NTA anode exhibited vertically aligned uniform nanotubes structure, and was demonstrated good performance on the electrochemical degradation of PFOA in water. The degradation rate, total organic carbon (TOC) removal rate and defluorination rate of PFOA reached 98.1 %, 93.3 % and 74.8 %, respectively, after electrolysis for 90 min at low current density of 2 mA cm-2. The energy consumption (7.6 Wh L-1) of this electrochemical oxidation system using Ti3+/TiO2-NTA anode for PFOA degradation was about 1 order of magnitude lower than using traditional PbO2 anodes. Cathodic polarization could effectively prolong the electrocatalytic activity of the anode by regenerating Ti3+ sites. PFOA molecular was underwent a rapidly mineralization to CO2 and F-, with only low concentration of short-chain perflfluorocarboxylic acids (PFCAs) intermediates identified. A possible electrochemical degradation mechanism of PFOA was proposed, in which the initial direct electron transfer (DET) on the anode to yield PFOA free radicals (C7F15COO•) and hydroxyl radicals (•OH) oxidation were greatly enhanced. This presented study provides a novel approach for the purification of the recalcitrant PFOA from wastewaters.

Blue-light emitting aminated pectin for detecting Cu2+ ion.

This research studied the chemo-sensing of low-cost aminated pectin (PE) obtained by a facile calcination under ammonia gas at temperature no higher than 175 °C without excessive use of alkaline, acid or solvents. The ammonia gas was found to replace the hydroxyl and methoxyl group, enhancing the crystallinity and solubility of the resultant pectin than those calcined in air or in 5% H2. Though the increase of light absorption could be attributed mainly to the dehydration during calcination which caused the formation of CC double bond or aromatic ring, the N incorporation could be important to the photoluminescence (PL) emission. The PL quenching of the blue fluorescent aminated pectin showed a good linearity with the concentration of Cu2+, Fe3+ and the highest sensitivity toward Cu2+ among the investigated metal ions. In order to further increase the PL quenching toward Cu2+ and decrease the interference of Fe3+, a method involving H2O2 and ultraviolet illumination was developed to catalyze the oxidation of fluorophores on the polymer. This work provides new horizon on the modification and application of pectin in chemosensing.

A Bibliometric Analysis on Nonpoint Source Pollution: Current Status, Development, and Future.

Nonpoint source pollution (NPS) has become the leading factor of global water quality problems, attracting great attention from governments and researchers in various countries. Based on this situation, understanding the current research status of NPS can help guide future research. However, most of the current reviews only describe the research status of some specific aspects but fail to quantify the research hotspots and development trends on the whole, which limits the overall understanding of NPS. In this paper, bibliometrics was used to study the current status, hotspots, and frontiers of NPS research during 1991-2015, and the future research development was predicted. Over the past 15 years, there has been a remarkable growth trend in publication output, and the participation of countries/territories has also increased. Journal of Environmental Quality, Journal of Hydrology, and Total Environmental Science were the top three journals. Sharpley AN and Arnold JG from the USA were the most productive authors with the best quality articles. The major author clusters and research regions are located in North America and Europe, followed by East Asia. The United States dominates this research field, with the largest number of independent and collaborative articles. Chinese authors gained more attention through international cooperation. Keyword analysis confirmed that water quality and nutrients were the main concerns of NPS pollution research, which mainly involved a number of research topics, such as pollutant emission reduction research and the evaluation and simulation of pollutants' migration and their transformation under different situations, while pesticides were less of a concern, which suggests that the abuse of pesticides has come under control. Meanwhile, SWAT was the dominating model in the last decade partly because it satisfied the growing needs of watershed-scale management.

Metal oxide nanoparticles resonate to ammonium removal through influencing Mg2+ absorption by Pseudomonas putida Y-9.

Most metal oxide nanoparticles (NPs) can impact ammonium removal, but the underlying mechanism remains unclear. In this study, high doses of NiO, CuO, ZnO and TiO2 (>1 mg/L) inhibited the ammonium removal performance of Pseudomonas putida Y-9. Interestingly, low levels of CuO NPs (0.1, 0.5 mg/L) and NiO NPs (0.1 mg/L) enhanced ammonium removal efficiency. Moreover, a decrease in Mg2+ levels was significantly positively correlated with ammonium removal efficiency, while negatively correlated with the Ti2+, Zn2+, and Cu2+ release of NPs. Further research on effect of NPs and their corresponding cations on ammonium removal revealed that four NPs affected Mg2+ absorption in Y-9 via different routes, thus impacting NH4+ removal efficiency, i.e., the effect of NiO NPs was caused by itself, TiO2 NPs' impact was solely due to the release Ti4+, while the influence of CuO NPs and ZnO NPs was based on both the particles and released ions.

Characteristics of nitrogen transformation and intracellular nitrite accumulation by the hypothermia bacterium Arthrobacter arilaitensis.

A new nitrite accumulation pathway was discovered in the nitrogen conversion process of Arthrobacter arilaitensis. The extracellular nitrite reached 0.65 and 43.66 mg/L with hydroxylamine and nitrate as the sole nitrogen source, respectively. The enzyme activities of ammonia monooxygenase, hydroxylamine oxidoreductase and nitrate reductase were 0.42, 0.0014 and 0.0049 U/mg protein, respectively. The activity of nitrite reductase was completely inhibited by diethyldithiocarbamate. Intriguingly, the intracellular nitrite accumulated as high as 43.0, 42.26, 39.94 and 35.01 mg/L, when the Arthrobacter arilaitensis was incubated with Luria-Bertani medium, ammonium, nitrate and nitrite as the nitrogen source, respectively. These results confirmed that the highest concentration of intracellular nitrite was accumulated when LB was selected as the nitrogen source, followed by ammonium and nitrate, then nitrite was the least. To date, biochemical mechanism responsible for the accumulation of a high concentration of intracellular nitrite is unknown.

Nitrous oxide produced directly from ammonium, nitrate and nitrite during nitrification and denitrification.

A hypothermia aerobic denitrifying bacterium, Pseudomonas taiwanensis strain J488, can effectively remove multiple nitrogen sources from wastewater at 15 °C. The ammonium, nitrate and nitrite removal efficiencies were 100 %, 92.61 % and 92.49 %, respectively. Strain J488 could survive with hydroxylamine as sole nitrogen source and its removal efficiency was 97.71 %. The removal efficiency of ammonium was 100 % even in the presence of the classical inhibitors of nitrification allylthiourea and diethyldithiocarbamate. These findings fundamentally changed the picture that the ammonia monooxygenase could be inhibited by the copper chelators of allylthiourea or diethyldithiocarbamate. Similarly, the nitrite removal capacity of strain J488 was not sensitive to inhibition by Pb2+, and its removal efficiency was also 100 %. Additionally, by identifying the intermediates accumulation of nitrification and denitrification, using nitrification and denitrification inhibitors, measuring enzyme activities and determining N2O concentrations, it was demonstrated that N2O could be produced directly from ammonium, nitrate and nitrite.

Determining the Shear Strength and Permeability of Soils for Engineering of New Paddy Field Construction in a Hilly Mountainous Region of Southwestern China.

As a constructed wetland ecosystem, paddy field plays an irreplaceable role in flood storage and detention, groundwater replenishment, environmental protection, and ecological balance maintenance. New paddy field construction can give full play to the production and ecological functions of paddy field and can adjust the development structure of the agricultural industry effectively. The soil properties of shear strength and permeability, which provide a theoretical basis for engineering design, construction, and post-operation, are important indexes in the site selection of new paddy field. The shear strength and permeability properties of soils from different land use types (vegetable field, gentle slope dryland, corn field, grapery, and abandoned dryland) for engineering new paddy field construction were investigated in this study. The results showed that the soil water content had a significant effect on the soil shear strength, internal friction angle, and cohesion. The total pressure required for soil destruction decreased with increasing water content under the same vertical pressure, resulting in easier destruction of soils. The internal friction angle decreased with increasing soil water content, and the soil cohesion first increased and then decreased with increasing soil water content. Considering that paddy fields were flooded for a long time, the soil strength properties had certain water sensitivity. Effective measures must be taken to reduce the change in soil water content, so as to ensure the stability of the embankment foundation, roadside ditch foundation, and cutting slope. In addition, the influence of changing soil water content on the strength properties of paddy soils should be fully considered in engineering design and construction, and the soil bulk density at the plough pan should reach at least 1.5 g cm-3 or more to ensure better water retention and the anti-seepage function of paddy field. The study can provide construction technology for engineering new paddy field construction in a hilly mountainous region of southwestern China.