Theoretical analysis of electrochromism of Ni-deficient nickel oxide - from bulk to surfaces.

The development of new electrochromic materials and devices, like smart windows, has an enormous impact on the energy efficiency of modern society. One of the crucial materials in this technology is nickel oxide. Ni-deficient NiO shows anodic electrochromism, whose mechanism is still under debate. We use DFT+U calculations to show that Ni vacancy generation results in the formation of hole polarons localized at the two oxygens next to the vacancy. In the case of NiO bulk, upon Li insertion or injection of an extra electron into Ni-deficient NiO, one hole gets filled, and the hole bipolaron is converted into a hole polaron well-localized at one O atom, resulting from the transition between oxidized (colored) to reduced (bleached) state. In the case of the Ni-deficient NiO(001) surface, the qualitatively same picture is obtained upon embedding Li, Na, and K into the Ni surface vacancy, reinforcing the conclusion that the electron injection, resulting in the filling of the hole states, is responsible for the modulation of the optical properties of NiO. Hence, our results suggest a new mechanism of Ni-deficient NiO electrochromism not related to the change of the Ni oxidation states, i.e., the Ni2+/Ni3+ transition, but based on the formation and annihilation of hole polarons in oxygen p-states.

Laser-Induced Graphene for Heartbeat Monitoring with HeartPy Analysis.

The HeartPy Python toolkit for analysis of noisy signals from heart rate measurements is an excellent tool to use in conjunction with novel wearable sensors. Nevertheless, most of the work to date has focused on applying the toolkit to data measured with commercially available sensors. We demonstrate the application of the HeartPy functions to data obtained with a novel graphene-based heartbeat sensor. We produce the sensor by laser-inducing graphene on a flexible polyimide substrate. Both graphene on the polyimide substrate and graphene transferred onto a PDMS substrate show piezoresistive behavior that can be utilized to measure human heartbeat by registering median cubital vein motion during blood pumping. We process electrical resistance data from the graphene sensor using HeartPy and demonstrate extraction of several heartbeat parameters, in agreement with measurements taken with independent reference sensors. We compare the quality of the heartbeat signal from graphene on different substrates, demonstrating that in all cases the device yields results consistent with reference sensors. Our work is a first demonstration of successful application of HeartPy to analysis of data from a sensor in development.

Viscose-Derived Activated Carbons Fibers as Highly Efficient Adsorbents for Dimethoate Removal from Water.

Extensive use of pesticides resulting in their accumulation in the environment presents a hazard for their non-target species, including humans. Hence, efficient remediation strategies are needed, and, in this sense, adsorption is seen as the most straightforward approach. We have studied activated carbon fibers (ACFs) derived from viscose fibers impregnated with diammonium hydrogen phosphate (DAHP). By changing the amount of DAHP in the impregnation step, the chemical composition and textural properties of ACFs are effectively tuned, affecting their performance for dimethoate removal from water. The prepared ACFs effectively reduced the toxicity of treated water samples, both deionized water solutions and spiked tap water samples, under batch conditions and in dynamic filtration experiments. Using the results of physicochemical characterization and dimethoate adsorption measurements, multiple linear regression models were made to reliably predict performance towards dimethoate removal from water. These models can be used to quickly screen among larger sets of possible adsorbents and guide the development of novel, highly efficient adsorbents for dimethoate removal from water.

A Review of Nanocomposite-Modified Electrochemical Sensors for Water Quality Monitoring.

Electrochemical sensors play a significant role in detecting chemical ions, molecules, and pathogens in water and other applications. These sensors are sensitive, portable, fast, inexpensive, and suitable for online and in-situ measurements compared to other methods. They can provide the detection for any compound that can undergo certain transformations within a potential window. It enables applications in multiple ion detection, mainly since these sensors are primarily non-specific. In this paper, we provide a survey of electrochemical sensors for the detection of water contaminants, i.e., pesticides, nitrate, nitrite, phosphorus, water hardeners, disinfectant, and other emergent contaminants (phenol, estrogen, gallic acid etc.). We focus on the influence of surface modification of the working electrodes by carbon nanomaterials, metallic nanostructures, imprinted polymers and evaluate the corresponding sensing performance. Especially for pesticides, which are challenging and need special care, we highlight biosensors, such as enzymatic sensors, immunobiosensor, aptasensors, and biomimetic sensors. We discuss the sensors' overall performance, especially concerning real-sample performance and the capability for actual field application.

Non-thermal plasma needle as an effective tool in dimethoate removal from water.

Intensive use of pesticides requires innovative approaches for their removal from the environment. Here we report the method for degradation of dimethoate in water using non-thermal plasma needle and analyze kinetics of dimethoate removal and possible degradation pathways. The effects of dimethoate initial concentration, plasma treatment time, Argon flow rate and the presence of radical promoters on the effectiveness of proposed method are evaluated. With argon flow rate of 0.5 slm (standard litres per minute) 1 × 10-4 M dimethoate can be removed within 30 min of treatment. Using UPLC analysis it was confirmed that one of the decomposition products is dimethoate oxo-analogue omethoate, which is in fact more toxic than dimethoate. However, the overall toxicity of contaminated water was reduced upon the treatment. The addition of H2O2 as a free radical promoter enhances dimethoate removal, while K2S2O8 results with selective conversion to omethoate. Using mass spectrometry in combination with the theoretical calculations, possible degradation pathways were proposed. The feasibility of the proposed method for dimethoate degradation in real water samples is confirmed. The proposed method is demonstrated as a highly effective approach for dimethoate removal without significant accumulation of undesirable toxic products and secondary waste.

Tunable reactivity of supported single metal atoms by impurity engineering of the MgO(001) support.

Development of novel materials may often require a rational use of high price components, like noble metals, in combination with the possibility to tune their properties in a desirable way. Here we present a theoretical DFT study of Au and Pd single atoms supported by doped MgO(001). By introducing B, C and N impurities into the MgO(001) surface, the interaction between the surface and the supported metal adatoms can be adjusted. Impurity atoms act as strong binding sites for Au and Pd adatoms and can help to produce highly dispersed metal particles. The reactivity of metal atoms supported by doped MgO(001), as probed by CO, is altered compared to their counterparts on pristine MgO(001). We find that Pd atoms on doped MgO(001) are less reactive than on perfect MgO(001). In contrast, Au adatoms bind CO much more strongly when placed on doped MgO(001). In the case of Au on N-doped MgO(001) we find that charge redistribution between the metal atom and impurity takes place even when not in direct contact, which enhances the interaction of Au with CO. The presented results suggest possible ways for optimizing the reactivity of oxide supported metal catalysts through impurity engineering.

Atomic adsorption on graphene with a single vacancy: systematic DFT study through the periodic table of elements.

Vacancies in graphene present sites of altered chemical reactivity and open possibilities to tune graphene properties by defect engineering. The understanding of chemical reactivity of such defects is essential for successful implementation of carbon materials in advanced technologies. We report the results of a systematic DFT study of atomic adsorption on graphene with a single vacancy for the elements of rows 1-6 of the periodic table of elements (PTE), excluding lanthanides. The calculations have been performed using the PBE, long-range dispersion interaction-corrected PBE (PBE+D2 and PBE+D3) and non-local vdW-DF2 functionals. We find that most elements strongly bind to the vacancy, except for the elements of groups 11 and 12, and noble gases, for which the contribution of dispersion interaction to bonding is most significant. The strength of the interaction with the vacancy correlates with the cohesive energy of the elements in their stable phases: the higher the cohesive energy is, the stronger bonding to the vacancy can be expected. As most atoms can be trapped at the SV site we have calculated the potentials of dissolution and found that in most cases the metals adsorbed at the vacancy are more "noble" than they are in their corresponding stable phases.

Lattice mismatch as the descriptor of segregation, stability and reactivity of supported thin catalyst films.

The increasing demand and high prices of advanced catalysts motivate a constant search for novel active materials with reduced contents of noble metals. The development of thin films and core-shell catalysts seems to be a promising strategy along this path. Using density functional theory we have analyzed a number of surface properties of supported bimetallic thin films with the composition A3B (where A = Pt and Pd, and B = Cu, Ag and Au). We focus on the surface segregation, dissolution stability and surface electronic structure. We also address the chemisorption properties of Pd3Au thin films supported by different substrates, by probing the surface reactivity with CO. We find a strong influence of the support in the case of mono- and bilayers, while the surface strain seems to be the predominant factor in determining the surface properties of supported trilayers and thicker films. In particular, we show that the studied properties of the supported trilayers can be predicted from the lattice mismatch between the overlayer and the support. Namely, if the strain dependence of the corresponding quantities for pure strained surfaces is known, the properties of strained supported trilayers can be reliably estimated. The obtained results can be used in the design of novel catalysts and predictions of the surface properties of supported ultrathin catalyst layers.

Electrochemical tuning of capacitive response of graphene oxide.

The increasing energy demands of modern society require a deep understanding of the properties of energy storage materials, as well as the tuning of their performance. We show that the capacitance of graphene oxide (GO) can be precisely tuned using a simple electrochemical reduction route. In situ resistance measurements, in combination with cyclic voltammetry measurements and Raman spectroscopy, have shown that upon reduction GO is irreversibly deoxygenated, which is further accompanied by structural ordering and an increase in electrical conductivity. The capacitance is maximized when the concentration of oxygen functional groups is properly balanced with the conductivity. Any further reduction and deoxygenation leads to a gradual loss of capacitance. The observed trend is independent of the preparation route and the exact chemical and structural properties of GO. It is proposed that an improvement in the capacitive properties of any GO can be achieved by optimization of its reduction conditions.

A DFT study of the interplay between dopants and oxygen functional groups over the graphene basal plane - implications in energy-related applications.

Understanding the ways graphene can be functionalized is of great importance for many contemporary technologies. Using density functional theory calculations we investigate how vacancy formation and substitutional doping by B, N, P and S affect the oxidizability and reactivity of the graphene basal plane. We find that the presence of these defects enhances the reactivity of graphene. In particular, these sites act as strong attractors for OH groups, suggesting that the oxidation of graphene could start at these sites or that these sites are the most difficult to reduce. Scaling between the OH and H adsorption energies is found on both reduced and oxidized doped graphene surfaces. Using the O2 molecule as a probe we show that a proper modelling of doped graphene materials has to take into account the presence of oxygen functional groups.

Improved catalysts for hydrogen evolution reaction in alkaline solutions through the electrochemical formation of nickel-reduced graphene oxide interface.

H2 production via water electrolysis plays an important role in hydrogen economy. Hence, novel cheap electrocatalysts for the hydrogen evolution reaction (HER) are constantly needed. Here, we describe a simple method for the preparation of composite catalysts for H2 evolution, consisting in simultaneous reduction of the graphene oxide film, and electrochemical deposition of Ni on its surface. The obtained composites (Ni@rGO), compared to pure electrodeposited Ni, show an improved electrocatalytic activity towards HER in alkaline media. We found that the activity of the Ni@rGO catalysts depends on the surface composition (Ni vs. C mole ratio) and on the level of structural disorder of the rGO support. We suggest that HER activity is improved via Hads spillover from the Ni particles to the rGO support, where quick recombination to molecular hydrogen is favored. A deeper insight into such a mechanism of H2 production was achieved by kinetic Monte-Carlo simulations. These simulations enabled the reproduction of experimentally observed trends under the assumption that the support can act as a Hads acceptor. We expect that the proposed procedure for the production of novel HER catalysts could be generalized and lead to the development of a new generation of HER catalysts by tailoring the catalyst/support interface.

Structural, electronic, magnetic and chemical properties of B-, C- and N-doped MgO(001) surfaces.

Doping of simple oxide materials can give rise to new exciting physical and chemical properties and open new perspectives for a variety of possible applications. Here we use density functional theory calculations to investigate the B-, C- and N-doped MgO(001) surfaces. We have found that the investigated dopants induce magnetization of the system amounting to 3, 2 and 1 µB for B, C and N, respectively. The dopants are found to be in the X(2-) state and tend to segregate to the surface. These impurity sites also present the centers of altered chemical reactivity. We probe the chemisorption properties of the doped MgO(001) surfaces with the CO molecule and atomic O. The adsorption of CO is much stronger on B- and C-doped MgO(001) compared to pure MgO(001) as the impurity sites serve as potent electron donors. The situation is similar to the case of atomic oxygen, for which we find the adsorption energy of -8.78 eV on B-doped MgO(001). The surface reactivity changes locally around the dopant atom, which is mainly restricted to its first coordination shell. The presented results suggest doped MgO as a versatile multifunctional material with possible use as an adsorbent or a catalyst.

A general view on the reactivity of the oxygen-functionalized graphene basal plane.

In this contribution we inspect the adsorption of H, OH, Cl and Pt on oxidized graphene using DFT calculations. The introduction of epoxy and hydroxyl groups on the graphene basal plane significantly alters its chemisorption properties, which can be attributed to the deformation of the basal plane and the type and distribution of these groups. We show that a general scaling relation exists between the hydrogen binding energies and the binding energies of other investigated adsorbates, which allows for a simple probing of the reactivity of oxidized graphene with only one adsorbate. The electronic states of carbon atoms located within the 2 eV interval below the Fermi level are found to be responsible for the interaction of the basal plane with the chosen adsorbates. The number of electronic states situated in this energy interval is shown to correlate with hydrogen binding energies.

Bimetallic dimers adsorbed on a defect-free MgO(001) surface: bonding, structure and reactivity.

A large number of computational studies have been devoted to the investigation of monometallic clusters supported by MgO. However, in practice, catalysis shows that multicomponent catalytic systems often win in catalytic performance over single component systems. In this study, the geometrical and electronic structure, stability and chemisorption properties of M1M2 metal dimers (M1, M2 = Ru, Rh, Pd, Ir, Pt) supported by defect free MgO(001) have been investigated in the framework of density functional theory. The oxygen sites of MgO(001) are the preferred adsorption sites for all the studied clusters, the majority of them adsorbing parallel to the surface with metal atoms attached to two surface oxygen atoms. The energetics of M1M2 + MgO(001) formation shows that the adsorption complexes are stable and benefit from metal-oxygen and metal-metal interaction. The chemisorption properties of Pd and Pt atoms in PdM2 and PtM2 dimers are studied using CO as a probe molecule. A linear relationship between the CO chemisorption and the d-band center position of the reacting atom in the dimer is observed, extending the d-band center model to the case of highly under-coordinated metal atoms supported by a non-conductive material.

The effect of surface modification by reduced graphene oxide on the electrocatalytic activity of nickel towards the hydrogen evolution reaction.

To find cheap, efficient and durable hydrogen evolution reaction catalysts is one of the major challenges when developing an alkaline water electrolysis system. In this paper we describe an electrochemically reduced graphene oxide (RGO)-modified Ni electrode, which could be used as a pre-eminent candidate for such a system. The experimentally determined characteristics of this electrode showing superior electrocatalytic activity were complemented by density functional theory calculations. Thermodynamic considerations led to the conclusion that H atoms, formed upon H2O discharge on Ni, spill onto the RGO, which serves as an H adatom acceptor, enabling continuous cleaning of Ni-active sites and an alternative pathway for H2 production. This mode of action is rendered by the unique reactivity of RGO, which arises due to the presence of O surface groups within the graphene structure. The significant electrocatalytic activity and life time (>35 days) of the RGO towards the HER under conditions of alkaline water electrolysis are demonstrated.

Detection of H. pylori outer membrane protein (HopQ) biomarker using electrochemical impedimetric immunosensor with polypyrrole nanotubes and carbon nanotubes nanocomposite on screen-printed carbon electrode.

Helicobacter pylori (H. pylori) is classified as a class I carcinogen that colonizes the human gastrointestinal (GI) tract. The detection at low concentrations is crucial in combatting H. pylori. HopQ protein is located on H. pylori's outer membrane and is expressed at an early stage of contamination, which signifies it as an ideal biomarker. In this study, we presented the development of an electrochemical impedimetric immunosensor for the ultra-sensitive detection of HopQ at low concentrations. The sensor employed polypyrrole nanotubes (PPy-NTs) and carboxylated multi-walled carbon nanotubes (MWCNT-COOH) nanocomposite. PPy-NTs were chosen for their excellent conductivity, biocompatibility, and redox capabilities, simplifying sample preparation by eliminating the need to add redox probes upon measurement. MWCNT-COOH provided covalent binding sites for HopQ antibodies (HopQ-Ab) on the biosensor surface. Characterization of the biosensor was performed using scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), contact angle measurements, and electrochemical impedance spectroscopy (EIS), complemented by numerical semiempirical quantum calculations. The results demonstrated a dynamic linear range of 5 pg/mL to 1.063 ng/mL and an excellent selectivity, with the possibility of excluding interference using EIS data, specifically charge transfer resistance and double-layer capacitance as multivariants for the calibration curve. Using two EIS components, the limit of detection is calculated to be 2.06 pg/mL. The biosensor was tested with a spiked drinking water sample and showed a signal recovery of 105.5% when detecting 300 pg/mL of HopQ. This novel H. pylori biosensor offers reliable, simple, portable, and rapid screening of the bacteria.

Toward Humidity-Independent Sensitive and Fast Response Temperature Sensors Based on Reduced Graphene Oxide/Poly(vinyl alcohol) Nanocomposites.

Flexible temperature sensors are becoming increasingly important these days. In this work, we explore graphene oxide (GO)/poly(vinyl alcohol) (PVA) nanocomposites for potential application in temperature sensors. The influence of the mixing ratio of both materials, the reduction temperature, and passivation on the sensing performance has been investigated. Various spectroscopic techniques revealed the composite structure and atomic composition. These were complemented by semiempirical quantum chemical calculations to investigate rGO and PVA interaction. Scanning electron and atomic force microscopy measurements were carried out to evaluate dispersion and coated film quality. The temperature sensitivity has been evaluated for several composite materials with different compositions in the range from 10 to 80 °C. The results show that a linear temperature behavior can be realized based on rGO/PVA composites with temperature coefficients of resistance (TCR) larger than 1.8% K-1 and a fast response time of 0.3 s with minimal hysteresis. Furthermore, humidity influence has been investigated in the range from 10% to 80%, and a minor effect is shown. Therefore, we can conclude that rGO/PVA composites have a high potential for excellent passivation-free, humidity-independent, sensitive, and fast response temperature sensors for various applications. The GO reduction is tunable, and PVA improves the rGO/PVA sensor performance by increasing the tunneling effect and band gap energy, consequently improving temperature sensitivity. Additionally, PVA exhibits minimal water absorption, reducing the humidity sensitivity. rGO/PVA maintains its temperature sensitivity during and after several mechanical deformations.

Spent Coffee Grounds as an Adsorbent for Malathion and Chlorpyrifos-Kinetics, Thermodynamics, and Eco-Neurotoxicity.

Coffee is one of the most popular beverages, with around 10.5 million tons manufactured annually. The same amount of spent coffee grounds (SCGs) might harm the environment if disposed of carelessly. On the other hand, pesticide contamination in food and biowaste is a rising problem. Because pesticides are hazardous and can cause serious health consequences, it is critical to understand how they interact with food biowaste materials. However, it is also a question if biowaste can be used to remediate rising pesticide residues in the environment. This study investigated the interactions of SCGs with the organophosphate pesticides malathion (MLT) and chlorpyrifos (CHP) and addressed the possibility of using SCGs as adsorbents for the removal of these pesticides from water and fruit extracts. The kinetics of MLT and CHP adsorption on SCGs fits well with the pseudo-first-order kinetic model. The Langmuir isotherm model best describes the adsorption process, giving the maximal adsorption capacity for MLT as 7.16 mg g-1 and 7.00 mg g-1 for CHP. Based on the thermodynamic analysis, it can be deduced that MLT adsorption on SCGs is exothermic, while CHP adsorption is an endothermic process. The adsorption efficiency of MLT and CHP using SCGs in a complicated matrix of fruit extracts remained constant. The neurotoxicity results showed that no more toxic products were formed during adsorption, indicating that SCGs are a safe-to-use adsorbent for pesticide removal in water and fruit extracts.

Carbonization of MOF-5/Polyaniline Composites to N,O-Doped Carbon/ZnO/ZnS and N,O-Doped Carbon/ZnO Composites with High Specific Capacitance, Specific Surface Area and Electrical Conductivity.

Composites of carbons with metal oxides and metal sulfides have attracted a lot of interest as materials for energy conversion and storage applications. Herein, we report on novel N,O-doped carbon/ZnO/ZnS and N,O-doped carbon/ZnO composites (generally named C-(MOF-5/PANI)), synthesized by the carbonization of metal-organic framework MOF-5/polyaniline (PANI) composites. The produced C-(MOF-5/PANI)s are comprehensively characterized in terms of composition, molecular and crystalline structure, morphology, electrical conductivity, surface area, and electrochemical behavior. The composition and properties of C-(MOF-5/PANI) composites are dictated by the composition of MOF-5/PANI precursors and the form of PANI (conducting emeraldine salt (ES) or nonconducting emeraldine base). The ZnS phase is formed only with the PANI-ES form due to S-containing counter-ions. XRPD revealed that ZnO and ZnS existed as pure wurtzite crystalline phases. PANI and MOF-5 acted synergistically to produce C-(MOF-5/PANI)s with high SBET (up to 609 m2 g-1), electrical conductivity (up to 0.24 S cm-1), and specific capacitance, Cspec, (up to 238.2 F g-1 at 10 mV s-1). Values of Cspec commensurated with N content in C-(MOF-5/PANI) composites (1-10 wt.%) and overcame Cspec of carbonized individual components PANI and MOF-5. By acid etching treatment of C-(MOF-5/PANI), SBET and Cspec increased to 1148 m2 g-1 and 341 F g-1, respectively. The developed composites represent promising electrode materials for supercapacitors.

Hydrogen Evolution Reaction on Ultra-Smooth Sputtered Nanocrystalline Ni Thin Films in Alkaline Media-From Intrinsic Activity to the Effects of Surface Oxidation.

Highly effective yet affordable non-noble metal catalysts are a key component for advances in hydrogen generation via electrolysis. The synthesis of catalytic heterostructures containing established Ni in combination with surface NiO, Ni(OH)2, and NiOOH domains gives rise to a synergistic effect between the surface components and is highly beneficial for water splitting and the hydrogen evolution reaction (HER). Herein, the intrinsic catalytic activity of pure Ni and the effect of partial electrochemical oxidation of ultra-smooth magnetron sputter-deposited Ni surfaces are analyzed by combining electrochemical measurements with transmission electron microscopy, selected area electron diffraction, X-ray photoelectron spectroscopy, and atomic force microscopy. The experimental investigations are supplemented by Density Functional Theory and Kinetic Monte Carlo simulations. Kinetic parameters for the HER are evaluated while surface roughening is carefully monitored during different Ni film treatment and operation stages. Surface oxidation results in the dominant formation of Ni(OH)2, practically negligible surface roughening, and 3-5 times increased HER exchange current densities. Higher levels of surface roughening are observed during prolonged cycling to deep negative potentials, while surface oxidation slows down the HER activity losses compared to as-deposited films. Thus, surface oxidation increases the intrinsic HER activity of nickel and is also a viable strategy to improve catalyst durability.