A Theoretical Study on the Mechanisms Involved in Catalytic Dehydrogenation and Dehydration of Isopropanol on SrTiO3.

The dehydrogenation and dehydration of isopropanol on the SrO and TiO2 terminated surfaces, of the SrTiO3 perovskite, is addressed by periodic DFT calculations in order to shed light on the involved mechanisms. The results show that the dehydrogenation occurs through a mechanism involving the dissociative adsorption of the alcohol on the SrO terminated surface, followed the nucleophilic attack of a hydride species on the previously adsorbed hydrogen atom to form molecular hydrogen and the corresponding carbonyl compound. The dehydration instead occurs by the molecular adsorption of the alcohol on the TiO2 terminated surface, followed by various possible E1 elimination pathways leading to the formation of the corresponding alkene and a water molecule. The article reports a thorough study on the involved mechanisms, including identification of the transition states and intermediates along the reaction paths, and evaluation of the respective activation barriers, as well. Thus, this article provides significant insights about the mechanisms of dehydrogenation and dehydration of isopropanol on the SrTiO3 , not reported earlier in literature. The calculated barrier energies are in good agreement with experimental values.

Catalytic Selective Oxidation of ß-O-4 Bond in Phenethoxybenzene as a Lignin Model Using (TBA)5[PMo10V2O40] Nanocatalyst: Optimization of Operational Conditions.

The catalytic oxidation of phenethoxybenzene as a lignin model compound with a ß-O-4 bond was conducted using the Keggin-type polyoxometalate nanocatalyst (TBA)5[PMo10V2O40]. The optimization of the process's operational conditions was carried out using response surface methodology. The statistically significant variables in the process were determined using a fractional factorial design. Based on this selection, a central circumscribed composite experimental design was used to maximize the phenethoxybenzene conversion, varying temperature, reaction time, and catalyst load. The optimal conditions that maximized the phenethoxybenzene conversion were 137 °C, 3.5 h, and 200 mg of catalyst. In addition, under the optimized conditions, the Kraft lignin catalytic depolymerization was carried out to validate the effectiveness of the process. The depolymerization degree was assessed by gel permeation chromatography from which a significant decrease in the molar mass distribution Mw from 7.34 kDa to 1.97 kDa and a reduction in the polydispersity index PDI from 6 to 3 were observed. Furthermore, the successful cleavage of the ß-O-4 bond in the Kraft lignin was verified by gas chromatography-mass spectrometry analysis of the reaction products. These results offer a sustainable alternative to efficiently converting lignin into valuable products.

A rationale for the unlike potency of avibactam and ETX2514 against OXA-24 ß-lactamase.

Diazabicyclooctanone inhibitors such as ETX2514 and avibactam have shown enhanced inhibitory performance to fight the antibiotic resistance developed by pathogens. However, avibactam is ineffective against Acinetobacter baumannii infections, unlike ETX2514. The molecular basis for this difference has not been tackled from a molecular approach, precluding the knowledge of relevant information. In this article, the mechanisms involved in the inhibition of OXA-24 by ETX2514 and avibactam are studied theoretically by hybrid QM/MM calculations. The results show that both inhibitors share the same inhibition mechanisms, comprising acylation a deacylation stages. The involved mechanisms include the same number of steps, transition states and intermediates; although they differ in the involved activation barriers. This difference accounts for the dissimilar inhibitory ability of both inhibitors. The molecular reason for this is the endocyclic double bond in the piperidine ring of ETX2514 increasing the ring strain and chemical reactivity on the N6 and C7 atoms, besides the methyl substituent, which enhance the hydrophobic character of the ring. Furthermore, Lys218 and the carboxylated Lys84 of ETX2514, play a crucial role in the mechanism by coordinating their protonation states in an on/off (protonated/deprotonated) manner, favoring the proton transference between the residues and the inhibitor.

Influence of LiTaO3 (0001) and KTaO3 (001) Perovskites Structures on the Molecular Adsorption of Styrene and Styrene oxide: A Theoretical Insight by Periodic DFT Calculations.

In this research, the adsorption of styrene and styrene oxide, both biomass derivatives, on KTaO3 (001) and LiTaO3 (0001) perovskite-like structures was studied from a theoretical point of view. The study was carried out using density functional theory (DFT) calculations. The adsorption phenomenon was deeply studied by calculating the adsorption energies (Eads ), adsorbate-surface distances (Å) and evaluating the differences of charge density and charge transfer (ΔCT). For complexes adsorbed on KTaO3 (TaO2 , KO and K(OH)2 exposed layers), the highest Eads was found for styrene oxide, attributed to the oxygen reactivity of the epoxy group describing a strong interaction with the surface. However, when evaluating a K(O)2 model, a more favorable interaction of styrene with the surface is observed, resulting in a high Eads of -9.9 eV and a ΔCT of 3.1e. For LiTaO3 , more favorable interactions are found for both adsorbates compared to KTaO3 , evidenced by the higher adsorption energies and charge density differences, particularly for the styrene complex adsorbed on TaO2 exposed layer (Eads : -10.2 eV). For the LiO termination, the surface exposed oxygens are fundamental for the adsorption of styrene and styrene oxide, leading to a considerable structural distortion. The obtained results thus provide understanding of the structural features, surface reactivity and adsorption sites of LiTaO3 and KTaO3 perovskite in the context of a heterogeneous catalytic process, such as the oxidation of styrene.

Preparation and characterization of a supported system of Ni2P/Ni12P5 nanoparticles and their use as the active phase in chemoselective hydrogenation of acetophenone.

Ni2P/Ni12P5 nanoparticles were obtained by thermal decomposition of nickel organometallic salt at low temperature. The use of different characterization techniques allowed us to determine that this process produced a mixture of two nickel phosphide phases: Ni2P and Ni12P5. These nickel phosphides nanoparticles, supported on mesoporous silica, showed activity and high selectivity for producing the hydrogenation of the acetophenone carbonyl group to obtain 1-phenylethanol. This is a first report that demonstrates the ability of supported Ni2P/Ni12P5 nanoparticles to produce the chemoselective hydrogenation of acetophenone. We attribute these special catalytic properties to the particular geometry of the Ni-P sites on the surface of the nanoparticles. This is an interesting result because the nickel phosphides have a wide composition range (from Ni3P to NiP3), with different crystallographic structures, therefore we think that different phases could be active and selective to hydrogenate many important molecules with more than one functional group.

MnO2/TiO2-Catalyzed ozonolysis: enhancing Pentachlorophenol degradation and understanding intermediates.

Pentachlorophenol is a pesticide widely known for its harmful effects on sewage, causing harm to the environment. In previous studies, our group identified adsorption as a crucial factor in catalytic ozonation processes, and subsequent observations revealed the catalyst's role in reducing toxicity during degradation. In this research, we quantified organochlorine intermediates and low molecular weight organic acids generated under optimal pH conditions (pH 9), with and without the catalyst. Additionally, we assessed the reactivity of these intermediates through theoretical calculations. Our findings indicate that the catalyst reduces the duration of intermediates. Additionally, the presence of CO2 suggests enhanced mineralization of pentachlorophenol, a process notably facilitated by the catalyst. Theoretical calculations, such as Fukui analysis, offer insights into potential pathways for the dechlorination of aromatic molecules by radicals like OH, indicating the significance of this pathway.

Black Trumpet Mushroom-like ZnS incorporated with Cu3P: Noble metal free photocatalyst for superior photocatalytic H2 production.

The development of the efficient photocatalysts with improved photoexcited charge separation and transfer is an essential for the effective photocatalytic H2 generation using light energy. So far, owing to the unique properties and characteristics, the transition metal phosphides (TMPs) have been proven to be high performance co-catalysts to replace some of the classic precious metal materials in the photocatalytic water splitting. In the present work, we report a novel copper phosphide (Cu3P) as a co-catalyst to form a well-designed fabricated photocatalyst with blacktrumpet mushroom-like ZnS semiconductor for the first time. The synthesis of Cu3P/ZnS consists of two-step hydrothermal and ball milling methods. The physical properties of the materials so prepared were characterized by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), transmission electron microscopy (TEM), ultraviolet-visible diffuse reflectance spectroscopy (UV-DRS), X-ray photoelectron spectroscopy (XPS) and Brunauer-Emmett-Teller (BET) analyses. In order to study the role of Cu3P, electrochemical impedance spectroscopy (EIS) measurements were used to investigate the photogenerated charge properties of ZnS. The experiments of photocatalytic production of H2 confirm that the Cu3P co-catalysts effectively promote the separation of photogenerated charge carriers in ZnS, and consequently enhance the H2 evolution activity. The 3% Cu3P/ZnS sample delivers the highest catalyst activity and the consistent H2 evolution rate is14,937 µmol h-1 g-1cat, which is 10-fold boosted compared to the pristine ZnS. The stability of the catalyst was tested by reusing the used 3% Cu3P/ZnS photocatalyst in five consecutive runs, and their respective activity in the H2 production activity was evaluated. A possible mechanism is proposed and discussed.

Chiral Pt/ZrO2 catalysts. Enantioselective hydrogenation of 1-phenyl-1,2-propanedione.

The enantioselective hydrogenation of 1-phenyl-1,2-propanedione over Pt colloids stabilized with (R,S)-4,5-dihydro-4,5-diphenyl-2-(6-cyanopyridinyl)imidazoline (CI) supported on a meso-structured ZrO(2) under a pressure of 40 bar of H(2) at 298 K has been investigated(.) The metal loading in all catalysts was 1 wt%. The effect of the amount of chiral modifier on the metal particle size and on the catalytic behavior was analyzed. It was found that as the CI/Pt molar ratio increases from 2.5 to 3.5 the Pt crystal size decreases from 3.0 to 1.8 nm. All catalysts were very active in the studied reaction, with the most active one being the catalyst with smaller Pt particles, whereas the selectivity is higher in those catalysts with larger chiral modified Pt metal particles.

The Effect of the ZrO2 Loading in SiO2@ZrO2-CaO Catalysts for Transesterification Reaction.

The effect of the ZrO2 loading was studied on spherical SiO2@ZrO2-CaO structures synthetized by a simple route that combines the Stöber and sol-gel methods. The texture of these materials was determined using SBET by N2 adsorption, where the increment in SiO2 spheres' surface areas was reached with the incorporation of ZrO2. Combined the characterization techniques of using different alcoholic dissolutions of zirconium (VI) butoxide 0.04 M, 0.06 M, and 0.08 M, we obtained SiO2@ZrO2 materials with 5.7, 20.2, and 25.2 wt % of Zr. Transmission electron microscopy (TEM) analysis also uncovered the shape and reproducibility of the SiO2 spheres. The presence of Zr and Ca in the core-shell was also determined by TEM. X-ray diffraction (XRD) profiles showed that the c-ZrO2 phase changed in to m-ZrO2 by incorporating calcium, which was confirmed by Raman spectroscopy. The purity of the SiO2 spheres, as well as the presence of Zr and Ca in the core-shell, was assessed by the Fourier transform infrared (FTIR) method. CO2 temperature programmed desorption (TPD-CO2) measurements confirmed the increment in the amount of the basic sites and strength of these basic sites due to calcium incorporation. The catalyst reuse in FAME production from canola oil transesterification allowed confirmation that these calcium core@shell catalysts turn out to be actives and stables for this reaction.

Mesoporous Palladium N,N'-Bis(3-Allylsalicylidene)o-Phenylenediamine-Methyl Acrylate Resins as Heterogeneous Catalysts for the Heck Coupling Reaction.

Palladium N,N'-bis(3-allylsalicylidene)o-phenylenediamine complex (PdAS) immobilized onto mesoporous polymeric methyl acrylate (MA) based resins (PdAS(x)-MA, x = 1, 2, 5, or 10 wt.%) were successfully prepared as heterogeneous catalysts for the Heck reaction. The catalysts were synthesized via radical suspension polymerization using PdAS as a metal chelate monomer, divinylbenzene and MA as co-monomers. The effect of the PdAS(x) content on the physicochemical properties of the resins is also reported. The catalysts were characterized by using a range of analytical techniques. The large surface area (>580 m2·g-1) and thermal stability (up to 250 °C) of the PdAS(x)-MA materials allows their application as catalysts in the C-C coupling reaction between iodobenzene and MA in the presence of trimethylamine at 120 °C using DMF as the solvent. The PdAS(10)-MA catalyst exhibited the highest catalytic performance with no significant catalytic loss being observed after five reuses, thereby indicating excellent catalyst stability in the reaction medium.

Magnetic Fe2O3⁻SiO2⁻MeO2⁻Pt (Me = Ti, Sn, Ce) as Catalysts for the Selective Hydrogenation of Cinnamaldehyde. Effect of the Nature of the Metal Oxide.

The type of metal oxide affects the activity and selectivity of Fe2O3⁻SiO2⁻MeO2⁻Pt (Me = Ti, Sn, Ce) catalysts on the hydrogenation of cinnamaldehyde. The double shell structure design is thought to protect the magnetic Fe2O3 cores, and also act as a platform for depositing a second shell of TiO2, SnO2 or CeO2 metal oxide. To obtain a homogeneous metallic dispersion, the incorporation of 5 wt % of Pt was carried out over Fe2O3⁻SiO2⁻MeO2 (Me = Ti, Sn, Ce) structures modified with (3-aminopropyl)triethoxysilane by successive impregnation-reduction cycles. The full characterization by HR-TEM, STEM-EDX, XRD, N2 adsorption isotherm at -196 °C, TPR-H2 and VSM of the catalysts indicates that homogeneous core-shell structures with controlled nano-sized magnetic cores, multi-shells and metallic Pt were obtained. The nature of the metal oxide affects the Pt nanoparticle sizes where the mean Pt diameter is in the order: ⁻TiO2⁻Pt > ⁻SnO2⁻Pt > ⁻CeO2⁻Pt. Among the catalysts studied, ⁻CeO2⁻Pt had the best catalytic performance, reaching the maximum of conversion at 240 min. of reaction without producing hydrocinnamaldehyde (HCAL). It also showed a plot volcano type for the production of cinnamic alcohol (COL), with 3-phenyl-1-propanol (HCOL) as a main product. The ⁻SnO2⁻Pt catalyst showed a poor catalytic performance attributable to the Pt clusters' occlusion in the irregular surface of the ⁻SnO2. Finally, the ⁻TiO2⁻Pt catalyst showed a continuous production of COL with a 100% conversion and 65% selectivity at 600 min of reaction.

Magnetic Fe3O4@SiO2-Pt and Fe3O4@SiO2-Pt@SiO2 Structures for HDN of Indole.

The effect of a second porous SiO2 shell in the activity and selectivity of the Fe3O4@SiO2-Pt catalyst in the hydrodenitrogenation of indole is reported. The double Fe3O4@SiO2-Pt@SiO2 structure was prepared by coating Fe3O4 nanoparticles with tetraethyl orthosilicate (TEOS) with a further impregnation of 1.0 wt.% of Pt on the (3-aminopropyl)triethoxysilane functionalized Fe3O4@SiO2 structures. The second porous SiO2 shell, obtained by using a hexadecyltrimethylammonium bromide (CTAB) template, covered the Fe3O4@SiO2-Pt catalyst with a well-defined and narrow pore-sized distribution. The full characterization by TEM, inductively coupled plasma-optical emission spectroscopy (ICP-OES), XRD, and N2 adsorption isotherm at 77 K and vibrating sample magnetometry (VSM) of the catalysts indicates homogeneous core@shell structures with a controlled nano-size of metallic Pt. A significant effect of the double SiO2 shell in the catalytic performance was demonstrated by both a higher activity to eliminate the nitrogen atom of the indole molecule present in model liquid fuel and the improvement of the catalytic stability reaching four consecutive reaction cycles with only a slight conversion level decrease.

Novel Route to Obtain Carbon Self-Doped TiO2 Mesoporous Nanoparticles as Efficient Photocatalysts for Environmental Remediation Processes under Visible Light.

Titanium dioxide materials were synthesized using two different methods. The samples were characterized by X-ray diffraction (XRD), UV-Visible diffusion reflectance spectroscopy (UV-Vis DR), Raman spectroscopy, N2 adsorption/desorption, scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX), transmission electron spectroscopy (TEM) and X-ray photoelectron spectroscopy (XPS). Although both kind of materials were found to have mesoporous structure and anatase crystalline phase, one of them was obtained from a synthesis method that does not involve the use of surfactants, and therefore, does not require calcination at high temperatures. This implies that the synthesized solid was self-doped with carbon species, coming only from the same source used for titanium. Then, the relationship between the presence of these species, the final calcination temperature, and the photocatalytic activity of the solids was studied in terms of the degradation and mineralization of an Acid Orange 7 aqueous solution, under visible radiation. A photosensitizing effect caused by the non-metal presence, that allows the solid to extend its absorption range, was found. Hence, a novel route to prepare C-modified photoactive mesoporous TiO2, simpler and cheaper, where neither a template nor an external carbon source is used, could be performed.