Dipole reorientation and local density of optical states influence the emission of light-emitting electrochemical cells.

Herein, we analyze the temporal evolution of the electroluminescence of light-emitting electrochemical cells (LECs), a thin-film light-emitting device, in order to maximize the luminous power radiated by these devices. A careful analysis of the spectral and angular distribution of the emission of LECs fabricated under the same experimental conditions allows describing the dynamics of the spatial region from which LECs emit, i.e. the generation zone, as bias is applied. This effect is mediated by dipole reorientation within such an emissive region and its optical environment, since its spatial drift yields a different interplay between the intrinsic emission of the emitters and the local density of optical states of the system. Our results demonstrate that engineering the optical environment in thin-film light-emitting devices is key to maximize their brightness.

Highly Stable Red-Light-Emitting Electrochemical Cells.

The synthesis and characterization of a series of new cyclometalated iridium(III) complexes [Ir(ppy)2(N∧N)][PF6] in which Hppy = 2-phenylpyridine and N∧N is (pyridin-2-yl)benzo[d]thiazole (L1), 2-(4-(tert-butyl)pyridin-2-yl)benzo[d]thiazole (L2), 2-(6-phenylpyridin-2-yl)benzo[d]thiazole (L3), 2-(4-(tert-butyl)-6-phenylpyridin-2-yl)benzo[d]thiazole (L4), 2,6-bis(benzo[d]thiazol-2-yl)pyridine (L5), 2-(pyridin-2-yl)benzo[d]oxazole (L6), or 2,2'-dibenzo[d]thiazole (L7) are reported. The single crystal structures of [Ir(ppy)2(L1)][PF6]·1.5CH2Cl2, [Ir(ppy)2(L6)][PF6]·CH2Cl2, and [Ir(ppy)2(L7)][PF6] have been determined. The new complexes are efficient red emitters and have been used in the active layers in light-emitting electrochemical cells (LECs). The effects of modifications of the 2-(pyridin-2-yl)benzo[d]thiazole ligand on the photoluminescence and LEC performance have been examined. Extremely stable red-emitting LECs are obtained, and when [Ir(ppy)2(L1)][PF6], [Ir(ppy)2(L2)][PF6], or [Ir(ppy)2(L3)][PF6] are used in the active layer, device lifetimes greater than 1000, 6000, and 4000 h, respectively, are observed.

Highly Stable and Efficient Light-Emitting Electrochemical Cells Based on Cationic Iridium Complexes Bearing Arylazole Ancillary Ligands.

A series of bis-cyclometalated iridium(III) complexes of general formula [Ir(ppy)2(N∧N)][PF6] (ppy- = 2-phenylpyridinate; N∧N = 2-(1H-imidazol-2-yl)pyridine (1), 2-(2-pyridyl)benzimidazole (2), 1-methyl-2-pyridin-2-yl-1H-benzimidazole (3), 2-(4'-thiazolyl)benzimidazole (4), 1-methyl-2-(4'-thiazolyl)benzimidazole (5)) is reported, and their use as electroluminescent materials in light-emitting electrochemical cell (LEC) devices is investigated. [2][PF6] and [3][PF6] are orange emitters with intense unstructured emission around 590 nm in acetonitrile solution. [1][PF6], [4][PF6], and [5][PF6] are green weak emitters with structured emission bands peaking around 500 nm. The different photophysical properties are due to the effect that the chemical structure of the ancillary ligand has on the nature of the emitting triplet state. Whereas the benzimidazole unit stabilizes the LUMO and gives rise to a 3MLCT/3LLCT emitting triplet in [2][PF6] and [3][PF6], the presence of the thiazolyl ring produces the opposite effect in [4][PF6] and [5][PF6] and the emitting state has a predominant 3LC character. Complexes with 3MLCT/3LLCT emitting triplets give rise to LEC devices with luminance values 1 order higher than those of complexes with 3LC emitting states. Protecting the imidazole N-H bond with a methyl group, as in complexes [3][PF6] and [5][PF6], shows that the emissive properties become more stable. [3][PF6] leads to outstanding LECs with simultaneously high luminance (904 cd m-2), efficiency (9.15 cd A-1), and stability (lifetime over 2500 h).

Anionic Cyclometalated Iridium(III) Complexes with a Bis-Tetrazolate Ancillary Ligand for Light-Emitting Electrochemical Cells.

A series of monoanionic Ir(III) complexes (2-4) of general formula [Ir(C^N)2(b-trz)](TBA) are presented, where C^N indicates three different cyclometallating ligands (Hppy = 2-phenylpyridine; Hdfppy = 2-(2,4-difluoro-phenyl)pyridine; Hpqu = 2-methyl-3-phenylquinoxaline), b-trz is a bis-tetrazolate anionic N^N chelator (H2b-trz = di(1H-tetrazol-5-yl)methane), and TBA = tetrabutylammonium. 2-4 are prepared in good yields by means of the reaction of the suitable b-trz bidentate ligand with the desired iridium(III) precursor. The chelating nature of the ancillary ligand, thanks to an optimized structure and geometry, improves the stability of the complexes, which have been fully characterized by NMR spectroscopy and high-resolution MS, while X-ray structure determination confirmed the binding mode of the b-trz ligand. Density functional theory calculations show that the highest occupied molecular orbital (HOMO) and lowest unoccupied molecular orbital (LUMO) are mainly localized on the metal center and the cyclometalating ligands, while the bis-tetrazolate unit does not contribute to the frontier orbitals. By comparison with selected classes of previously published cationic and anionic complexes with high ligand field and even identical cyclometallating moieties, it is shown that the HOMO-LUMO gap is similar, but the absolute energy of the frontier orbitals is remarkably higher for anionic vs cationic compounds, due to electrostatic effects. 2-4 exhibit reversible oxidation and reduction processes, which make them interesting candidates as active materials for light emitting electrochemical cells, along with red, green, and blue emission, thanks to the design of the C^N ligands. Photoluminescence quantum yields range from 28% (4, C^N = pqu, red emitter) to 83% (3, C^N = dfppy, blue emitter) in acetonitrile, with the latter compound reaching 95% in poly(methyl methacrylate) (PMMA) matrix. In thin films, the photoluminescence quantum yield decreases substantially probably due to the small intersite distance between the complexes and the presence of quenching sites. In spite of this, surprisingly stable electroluminescence was observed for devices employing complex 2, demonstrating the robustness of the anionic compounds.

Nontemplate synthesis of CH3NH3PbBr3 perovskite nanoparticles.

To date, there is no example in the literature of free, nanometer-sized, organolead halide CH3NH3PbBr3 perovskites. We report here the preparation of 6 nm-sized nanoparticles of this type by a simple and fast method based on the use of an ammonium bromide with a medium-sized chain that keeps the nanoparticles dispersed in a wide range of organic solvents. These nanoparticles can be maintained stable in the solid state as well as in concentrated solutions for more than three months, without requiring a mesoporous material. This makes it possible to prepare homogeneous thin films of these nanoparticles by spin-coating on a quartz substrate. Both the colloidal solution and the thin film emit light within a narrow bandwidth of the visible spectrum and with a high quantum yield (ca. 20%); this could be advantageous in the design of optoelectronic devices.

Iridium(III) complexes with phenyl-tetrazoles as cyclometalating ligands.

Ir(III) cationic complexes with cyclometalating tetrazolate ligands were prepared for the first time, following a two-step strategy based on (i) a silver-assisted cyclometalation reaction of a tetrazole derivative with IrCl3 affording a bis-cyclometalated solvato-complex P ([Ir(ptrz)2(CH3CN)2](+), Hptrz = 2-methyl-5-phenyl-2H-tetrazole); (ii) a substitution reaction with five neutral ancillary ligands to get [Ir(ptrz)2L](+), with L = 2,2'-bypiridine (1), 4,4'-di-tert-butyl-2,2'-bipyridine (2), 1,10-phenanthroline (3), and 2-(1-phenyl-1H-1,2,3-triazol-4-yl)pyridine (4), and [Ir(ptrz)2L2](+), with L = tert-butyl isocyanide (5). X-ray crystal structures of P, 2, and 3 were solved. Electrochemical and photophysical studies, along with density functional theory calculations, allowed a comprehensive rationalization of the electronic properties of 1-5. In acetonitrile at 298 K, complexes equipped with bipyridine or phenanthroline ancillary ligands (1-3) exhibit intense and structureless emission bands centered at around 540 nm, with metal-to-ligand and ligand-to-ligand charge transfer (MLCT/LLCT) character; their photoluminescence quantum yields (PLQYs) are in the range of 55-70%. By contrast, the luminescence band of 5 is weak, structured, and blue-shifted and is attributed to a ligand-centered (LC) triplet state of the tetrazolate cyclometalated ligand. The PLQY of 4 is extremely low (<0.1%) since its lowest level is a nonemissive triplet metal-centered ((3)MC) state. In rigid matrix at 77 K, all of the complexes exhibit intense luminescence. Ligands 1-3 are also strong emitters in solid matrices at room temperature (1% poly(methyl methacrylate) matrix and neat films), with PLQYs in the range of 27-70%. Good quality films of 2 could be obtained to make light-emitting electrochemical cells that emit bright green light and exhibit a maximum luminance of 310 cd m(-2). Tetrazolate cyclometalated ligands push the emission of Ir(III) complexes to the blue, when compared to pyrazolate or triazolate analogues. More generally, among the cationic Ir(III) complexes without fluorine substituents on the cyclometalated ligands, 1-3 exhibit the highest-energy MLCT/LLCT emission bands ever reported.

Light-emitting electrochemical cells using cyanine dyes as the active components.

Light-emitting electrochemical cells (LECs) based on cyanine molecules were prepared. High photoluminescence quantum yields were obtained for host-guest films using two cyanine dyes, reaching 27%. Sandwiching these films in between two electrodes allows for very stable near-infrared emission with a maximum radiant flux of 1.7 W m(-2) at an external quantum efficiency of 0.44%.

Efficient green-light-emitting electrochemical cells based on ionic iridium complexes with sulfone-containing cyclometalating ligands.

A new approach to obtain green-emitting iridium(III) complexes is described. The synthetic approach consists of introducing a methylsulfone electron-withdrawing substituent into a 4-phenylpyrazole cyclometalating ligand in order to stabilize the highest-occupied molecular orbital (HOMO). Six new complexes have been synthesized incorporating the conjugate base of 1-(4-(methylsulfonyl)phenyl)-1H-pyrazole as the cyclometalating ligand. The complexes show green emission and very high photoluminescence quantum yields in both diluted and concentrated films. When used as the main active component in light-emitting electrochemical cells (LECs), green electroluminance is observed. High efficiencies and luminances are obtained at low driving voltages. This approach for green emitters is an alternative to the widely used fluorine-based substituents in the cyclometalating ligands and opens new design possibilities for the synthesis of green emitters for LECs.

Phosphane tuning in heteroleptic [Cu(N

The synthesis and characterization of five [Cu(P^P)(N^N)][PF6] complexes in which P^P = 2,7-bis(tert-butyl)-4,5-bis(diphenylphosphino)-9,9-dimethylxanthene (tBu2xantphos) or the chiral 4,5-bis(mesitylphenylphosphino)-9,9-dimethylxanthene (xantphosMes2) and N^N = 2,2'-bipyridine (bpy), 6-methyl-2,2'-bipyridine (6-Mebpy) or 6,6'-dimethyl-2,2'-bipyridine (6,6'-Me2bpy) are reported. Single crystal structures of four of the compounds confirm that the copper(i) centre is in a distorted tetrahedral environment. In [Cu(xantphosMes2)(6-Mebpy)][PF6], the 6-Mebpy unit is disordered over two equally populated orientations and this disorder parallels a combination of two dynamic processes which we propose for [Cu(xantphosMes2)(N^N)]+ cations in solution. Density functional theory (DFT) calculations reveal that the energy difference between the two conformers observed in the solid-state structure of [Cu(xantphosMes2)(6-Mebpy)][PF6] differ in energy by only 0.28 kcal mol-1. Upon excitation into the MLCT region (λexc = 365 nm), the [Cu(P^P)(N^N)][PF6] compounds are yellow to orange emitters. Increasing the number of Me groups in the bpy unit shifts the emission to higher energies, and moves the Cu+/Cu2+ oxidation to higher potentials. Photoluminescence quantum yields (PLQYs) of the compounds are low in solution, but in the solid state PLQYs of up to 59% (for [Cu(tBu2xantphos)(6,6'-Me2bpy)]+) are observed. Increased excited-state lifetimes at low temperature are consistent with the complexes exhibiting thermally activated delayed fluorescence (TADF). This is supported by the small energy difference calculated between the lowest-energy singlet and triplet excited states (0.17-0.25 eV). The compounds were tested in simple bilayer light-emitting electrochemical cells (LECs). The optoelectronic performances of complexes containing xantphosMes2 were generally lower with respect to those with tBu2xantphos, which led to bright and efficient devices. The best performing LECs were obtained for the complex [Cu(tBu2xantphos)(6,6'-Me2bpy)][PF6] due to the increased steric hindrance at the N^N ligand, resulting in higher PLQY.

CF3 Substitution of [Cu(P

Herein, [Cu(P^P)(N^N)][PF6 ] complexes (P^P=bis[2-(diphenylphosphino)phenyl]ether (POP) or 4,5-bis(diphenylphosphino)-9,9-dimethylxanthene (xantphos); N^N=CF3 -substituted 2,2'-bipyridines (6,6'-(CF3 )2 bpy, 6-CF3 bpy, 5,5'-(CF3 )2 bpy, 4,4'-(CF3 )2 bpy, 6,6'-Me2 -4,4'-(CF3 )2 bpy)) are reported. The effects of CF3 substitution on their structure as well as their electrochemical and photophysical properties are also presented. The HOMO-LUMO gap was tuned by the N^N ligand; the largest redshift in the metal-to-ligand charge transfer (MLCT) band was for [Cu(P^P){5,5'-(CF3 )2 bpy}][PF6 ]. In solution, the compounds are weak yellow to red emitters. The emission properties depend on the substitution pattern, but this cannot be explained by simple electronic arguments. Among powders, [Cu(xantphos){4,4'-(CF3 )2 bpy}][PF6 ] has the highest photoluminescence quantum yield (PLQY; 50.3 %) with an emission lifetime of 12 µs. Compared to 298 K solution behavior, excited-state lifetimes became longer in frozen Me-THF (77 K; THF=tetrahydrofuran), thus indicating thermally activated delayed fluorescence (TADF). Time-dependent (TD)-DFT calculations show that the energy gap between the lowest-energy singlet and triplet excited states (0.12-0.20 eV) permits TADF. Light-emitting electrochemical cells (LECs) with [Cu(POP)+(6-CF3 bpy)][PF6 ], [Cu(xantphos)(6-CF3 bpy)][PF6 ], or [Cu(xantphos){6,6'-Me2 -4,4'-(CF3 )2 bpy}][PF6 ] emit yellow electroluminescence. The LEC with [Cu(xantphos){6,6'-Me2 -4,4'-(CF3 )2 bpy}][PF6 ] had the fastest turn-on time (8 min), and the LEC with the longest lifetime (t1/2 =31 h) contained [Cu(xantphos)(6-CF3 bpy)][PF6 ]; these LECs reached maximum luminances of 131 and 109 cd m-2 , respectively.

CF3 Substitution of [Cu(P

Invited for this month's cover are the research groups of Professors Catherine Housecroft and Edwin Constable from the University of Basel, Switzerland and Professor Enrique Ortí and Dr. Henk Bolink from the University of Valencia, Spain. These groups have a longstanding collaboration to investigate molecular electronic devices, in particular light-emitting electrochemical cells (LECs) and organic light-emitting diodes (OLEDs). The featured article highlights the development of LECs with copper(I)-based emitters for devices consisting of Earth-abundant materials. Read the full text of the article at 10.1002/cplu.201700501.

Peripheral halo-functionalization in [Cu(N

A series of heteroleptic [Cu(N^N)(P^P)][PF6] complexes is described in which P^P = bis(2-(diphenylphosphino)phenyl)ether (POP) or 4,5-bis(diphenylphosphino)-9,9-dimethylxanthene (xantphos) and N^N = 4,4'-diphenyl-6,6'-dimethyl-2,2'-bipyridine substituted in the 4-position of the phenyl groups with atom X (N^N = 1 has X = F, 2 has X = Cl, 3 has X = Br, 4 has X = I; the benchmark N^N ligand with X = H is 5). These complexes have been characterized by multinuclear NMR spectroscopy, mass spectrometry, elemental analyses and cyclic voltammetry; representative single crystal structures are also reported. The solution absorption spectra are characterized by high energy bands (arising from ligand-centred transitions) which are red-shifted on going from X = H to X = I, and a broad metal-to-ligand charge transfer band with λmax in the range 387-395 nm. The ten complexes are yellow emitters in solution and yellow or yellow-orange emitters in the solid-state. For a given N^N ligand, the solution photoluminescence (PL) spectra show no significant change on going from [Cu(N^N)(POP)]+ to [Cu(N^N)(xantphos)]+; introducing the iodo-functionality into the N^N domain leads to a red-shift in λ compared to the complexes with the benchmark N^N ligand 5. In the solid state, [Cu(1)(POP)][PF6] and [Cu(1)(xantphos)][PF6] (fluoro-substituent) exhibit the highest PL quantum yields (74 and 25%, respectively) with values of τ1/2 = 11.1 and 5.8 µs, respectively. Light-emitting electrochemical cells (LECs) with [Cu(N^N)(P^P)][PF6] complexes in the emissive layer have been tested. Using a block-wave pulsed current driving mode, the best performing device employed [Cu(1)(xantphos)]+ and this showed a maximum luminance (Lummax) of 129 cd m-2 and a device lifetime (t1/2) of 54 h; however, the turn-on time (time to reach Lummax) was 4.1 h. Trends in performance data reveal that the introduction of fluoro-groups is beneficial, but that the incorporation of heavier halo-substituents leads to poor devices, probably due to a detrimental effect on charge transport; LECs with the iodo-functionalized N^N ligand 4 failed to show any electroluminescence after 50 h.

Chiral Iridium(III) Complexes in Light-Emitting Electrochemical Cells: Exploring the Impact of Stereochemistry on the Photophysical Properties and Device Performances.

Despite hundreds of cationic bis-cyclometalated iridium(III) complexes having been explored as emitters for light-emitting electrochemical cells (LEECs), uniformly their composition has been in the form of a racemic mixture of Λ and Δ enantiomers. The investigation of LEECs using enantiopure iridium(III) emitters, however, remains unprecedented. Herein, we report the preparation, the crystal structures, and the optoelectronic properties of two families of cyclometalated iridium(III) complexes of the form of [(C^N)2Ir(dtBubpy)]PF6 (where dtBubpy is 4,4'-di-tert-butyl-2,2'-bipyridine) in both their racemic and enantiopure configurations. LEEC devices using Λ and Δ enantiomers as well as the racemic mixture of both families have been prepared, and the device performances were tested. Importantly, different solid-state photophysical properties exist between enantiopure and racemic emitters, which are also reflected in the device performances.

Luminescent osmium(ii) bi-1,2,3-triazol-4-yl complexes: photophysical characterisation and application in light-emitting electrochemical cells.

The series of osmium(ii) complexes [Os(bpy)3-n(btz)n][PF6]2 (bpy = 2,2'-bipyridyl, btz = 1,1'-dibenzyl-4,4'-bi-1,2,3-triazolyl, n = 0, n = 1, n = 2, n = 3), have been prepared and characterised. The progressive replacement of bpy by btz leads to blue-shifted UV-visible electronic absorption spectra, indicative of btz perturbation of the successively destabilised bpy-centred LUMO. For , a dramatic blue-shift relative to the absorption profile for is observed, indicative of the much higher energy LUMO of the btz ligand over that of bpy, mirroring previously reported data on analogous ruthenium(ii) complexes. Unlike the previously reported ruthenium systems, heteroleptic complexes and display intense emission in the far-red/near-infrared (λmax = 724 and 713 nm respectively in aerated acetonitrile at RT) as a consequence of higher lying, and hence less thermally accessible, (3)MC states. This assertion is supported by ground state DFT calculations which show that the dσ* orbitals of to are destabilised by between 0.60 and 0.79 eV relative to their Ru(ii) analogues. The homoleptic complex appears to display extremely weak room temperature emission, but on cooling to 77 K the complex exhibits highly intense blue emission with λmax 444 nm. As complexes to display room temperature luminescent emission and readily reversible Os(ii)/(iii) redox couples, light-emitting electrochemical cell (LEC) devices were fabricated. All LECs display electroluminescent emission in the deep-red/near-IR (λmax = 695 to 730 nm). Whilst devices based on and show inferior current density and luminance than LECs based on , the device utilising shows the highest external quantum efficiency at 0.3%.

[Ir(C

The synthesis of four cyclometallated [Ir(C^N)2(N^N)][PF6] compounds in which N^N is a substituted 2,2'-bipyridine (bpy) ligand and the naphthyl-centred ligand 2,7-bis(2-(2-(4-(pyridin-2-yl)phenoxy)ethoxy)ethoxy)naphthalene provides the two cyclometallating C^N units is reported. The iridium(iii) complexes have been characterized by 1H and 13C NMR spectroscopies, mass spectrometry and elemental analysis, and their electrochemical and photophysical properties are described. Comparisons are made with a model [Ir(ppy)2(N^N)][PF6] compound (Hppy = 2-phenylpyridine). The complexes containing the naphthyl-unit exhibit similar absorption spectra and excitation at 280 nm leads to an orange emission. The incorporation of the naphthalene unit does not lead to a desirable blue contribution to the emission. Density functional theory calculations were performed to investigate the geometries of the complexes in their ground and first triplet excited states, as well as the energies and compositions of the highest-occupied and lowest unoccupied molecular orbital (HOMO and LUMO) manifolds. Trends in the HOMO-LUMO gaps agree with those observed electrochemically. The energy difference between the LUMO and the lowest unoccupied MO located on the naphthyl unit (LUMO+7) is large enough to explain why there is no contribution from the naphthyl-centred triplet excited state to the phosphorescence emission. Singlet excited states were also investigated. Light-emitting electrochemical cells (LECs) using the [Ir(C^N)2(N^N)][PF6] and [Ir(ppy)2(N^N)][PF6] complexes in the emissive layer were made and evaluated. The presence of the naphthyl-bridge between the cyclometallating units does not significantly alter the device response.

Regioisomerism in cationic sulfonyl-substituted [Ir(C

A series of regioisomeric cationic iridium complexes of the type [Ir(C^N)2(bpy)][PF6] (bpy = 2,2'-bipyridine) is reported. The complexes contain 2-phenylpyridine-based cyclometallating ligands with a methylsulfonyl group in either the 3-, 4- or 5-position of the phenyl ring. All the complexes have been fully characterized, including their crystal structures. In acetonitrile solution, all the compounds are green emitters with emission maxima between 493 and 517 nm. Whereas substitution meta to the Ir-C bond leads to vibrationally structured emission profiles and photoluminescence quantum yields of 74 and 77%, placing a sulfone substituent in a para position results in a broad, featureless emission band, an enhanced quantum yield of 92% and a shorter excited-state lifetime. These results suggest a larger ligand-centred ((3)LC) character of the emissive triplet state in the case of meta substitution and a more pronounced charge transfer (CT) character in the case of para substitution. Going from solution to the solid state (powder samples and thin films), the emission maxima are red-shifted for all the complexes, resulting in green-yellow emission. Data obtained from electrochemical measurements and density functional theory calculations parallel the photophysical trends. Light-emitting electrochemical cells (LECs) based on the complexes were fabricated and evaluated. A maximum efficiency of 4.5 lm W(-1) at a maximum luminance of 940 cd m(-2) was observed for the LEC with the complex incorporating the sulfone substituent in the 4-position when operated under pulsed current driving conditions.

Efficient photovoltaic and electroluminescent perovskite devices.

Planar diode structures employing hybrid organic-inorganic methylammonium lead iodide perovskites lead to multifunctional devices exhibiting both a high photovoltaic efficiency and good electroluminescence. The electroluminescence strongly improves at higher current density applied using a pulsed driving method.

Exceptionally long-lived light-emitting electrochemical cells: multiple intra-cation π-stacking interactions in [Ir(C

A series of cyclometalated iridium(iii) complexes [Ir(C^N)2(N^N)][PF6] (N^N = 2,2'-bipyridine (1), 6-phenyl-2,2'-bipyridine (2), 4,4'-di-tert-butyl-2,2'-bipyridine (3), 4,4'-di-tert-butyl-6-phenyl-2,2'-bipyridine (4); HC^N = 2-(3-phenyl)phenylpyridine (HPhppy) or 2-(3,5-diphenyl)phenylpyridine (HPh2ppy)) are reported. They have been synthesized using solvento precursors so as to avoid the use of chlorido-dimer intermediates, chloride ion contaminant being detrimental to the performance of [Ir(C^N)2(N^N)][PF6] emitters in light-electrochemical cell (LEC) devices. Single crystal structure determinations and variable temperature solution 1H NMR spectroscopic data confirm that the pendant phenyl domains engage in multiple face-to-face π-interactions within the coordination sphere of the iridium(iii) centre. The series of [Ir(Phppy)2(N^N)]+ and [Ir(Ph2ppy)2(N^N)]+ complexes investigated include those with and without intra-cation face-to-face π-stacking. All the complexes display excellent luminescent properties, in particular when employed in thin solid films. The most important observation is that all the LECs using the [Ir(Phppy)2(N^N)]+ and [Ir(Ph2ppy)2(N^N)]+ emitters (i.e. with and without intra-cation π-stacking interactions) exhibit very stable luminance outputs over time, even when driven at elevated current densities. The most stable LEC had an extrapolated lifetime of more than 2500 hours under accelerated testing conditions.

[Cu(bpy)(P

Light-emitting electrochemical cells (LECs) containing [Cu(POP)(N^N)][PF6] (POP = bis(2-diphenylphosphinophenyl)ether, N^N = 6-methyl- or 6,6'-dimethyl-2,2'-bipyridine) exhibit luminance and efficiency surpassing previous copper(I)-containing LECs.

Modulation of the solubility of luminescent semiconductor nanocrystals through facile surface functionalization.

The solubility of luminescent quantum dots in solvents from hexane to water can be finely tuned by the choice of the countercations associated with carboxylate residues present on the nanocrystal surface. The resulting nanocrystals exhibit long term colloidal and chemical stability and maintain their photophysical properties.