RESUMEN
In this paper, a 3D conformal meta-lens designed for manipulating electromagnetic beams via height-to-phase control is proposed. The structure consists of a 40 × 20 array of tunable unit cells fabricated using 3D printing, enabling full 360° phase compensation. A novel automatic synthesizing method (ASM) with an integrated optimization process based on genetic algorithm (GA) is adopted here to create the meta-lens. Simulation using CST Microwave Studio and MATLAB reveals the antenna's beam deflection capability by adjusting phase compensations for each unit cell. Various beam scanning techniques are demonstrated, including single-beam, dual-beam generation, and orbital angular momentum (OAM) beam deflection at different angles of 0°, 10°, 15°, 25°, 30°, and 45°. A 3D-printed prototype of the dual-beam feature has been fabricated and measured for validation purposes, with good agreement between both simulation and measurement results, with small discrepancies due to 3D printing's low resolution and fabrication errors. This meta-lens shows promise for low-cost, high-gain beam deflection in mm-wave wireless communication systems, especially for sensing applications, with potential for wider 2D beam scanning and independent beam deflection enhancements.
RESUMEN
Antennas that generate orbital angular momentum (OAM) have the potential to significantly enhance the channel capacity of upcoming wireless systems. This is because different OAM modes that are excited from a shared aperture are orthogonal, which means that each mode can carry a distinct stream of data. As a result, it is possible to transmit multiple data streams at the same time and frequency using a single OAM antenna system. To achieve this, there is a need to develop antennas that can create several OAM modes. This study employs an ultrathin dual-polarized Huygens' metasurface to design a transmit array (TA) that can generate mixed-OAM modes. Two concentrically-embedded TAs are used to excite the desired modes by achieving the required phase difference according to the coordinate position of each unit cell. The prototype of the TA, which operates at 28 GHz and has a size of 11 × 11 cm 2, generates mixed OAM modes of -1 and -2 using dual-band Huygens' metasurfaces. To the best of the authors' knowledge, this is the first time that such a low-profile and dual-polarized OAM carrying mixed vortex beams has been designed using TAs. The maximum gain of the structure is 16 dBi.
RESUMEN
This paper presents a technique to design strongly coupled planar arrays with very high aperture efficiency. The key innovation is that, based on an irregular 2 × 1 array, very compact medium-sized arrays of size 2 × 2, 2 × 4, and 2 × 6 are constructed with very strong and constructive mutual coupling between the elements. In this way, a maximum aperture efficiency is reached for a given footprint of the array. The occupied space of the antenna in comparison with conventional linear patch arrays is studied. A prototype 2 × 4 array operating around 5.8 GHz is designed, fabricated, built, and measured. The results show a large bandwidth of 20% and a very high aperture efficiency of 100%, which is the largest found in the literature for similarly sized arrays. These results are important in view of the future Internet of Things, where small and medium-sized arrays are planned to be mounted on numerous devices where a very limited physical area is available.
RESUMEN
This paper presents a new design for a dual-band double-cylinder dielectric resonator antenna (CDRA) capable of efficient operation in microwave and mm-wave frequencies for 5G applications. The novelty of this design lies in the antenna's capability to suppress harmonics and higher-order modes, resulting in a significant improvement in antenna performance. Additionally, both resonators are made of dielectric materials with different relative permittivities. The design procedure involves the utilization of a larger cylinder-shaped dielectric resonator (D1), which is fed by a vertically mounted copper microstrip securely attached to its outer surface. An air gap is created at the bottom of (D1), and a smaller CDRA (D2) is inserted inside this gap, with its exit facilitated by a coupling aperture slot etched on the ground plane. Furthermore, a low-pass filter (LPF) is added to the feeding line of D1 to eliminate undesirable harmonics in the mm-wave band. The larger CDRA (D1) with a relative permittivity of 6 resonates at 2.4 GHz, achieving a realized gain of 6.7 dBi. On the other hand, the smaller CDRA (D2) with a relative permittivity of 12 resonates at a frequency of 28 GHz, reaching a realized gain of 15.2 dBi. The dimensions of each dielectric resonator can be independently manipulated to control the two frequency bands. The antenna exhibits excellent isolation between its ports, with scattering parameters (S12) and (S21) falling below -72/-46 dBi at the microwave and mm-wave frequencies, respectively, and not exceeding -35 dBi for the entire frequency band. The experimental results of the proposed antenna's prototype closely align with the simulated results, validating the design's effectiveness. Overall, this antenna design is well-suited for 5G applications, offering the advantages of dual-band operation, harmonic suppression, frequency band versatility, and high isolation between ports.
RESUMEN
In this paper, a wideband and high-gain circular polarised Fabry-Perot Resonator Antenna (FPRA) with a single partially reflective surface (PRS) layer is automatically generated and optimised using a VBA-based interface system between CST Microwave studio and Matlab. The proposed PRS layer is a promising superstrate for wideband and high-gain FP resonator antennas due to its relatively high reflection coefficient magnitude and positive phase gradient, which resemble that of the optimum PRS over the relevant frequency band. The circular polarisation was achieved using a sequential feeding network for a 2 × 2 array air-gapped slot-coupled elliptical patch antenna. The proposed design achieved an impedance bandwidth of 48.58% (15.3 GHz) ranging from 23.84 GHz to 39.14 GHz, and the -3 dB gain bandwidth was 22.42% (6.25 GHz) from 24.75 to 31 GHz, with a peak gain of 17.12 dB at 29 GHz, and an axial ratio bandwidth of 21.75% (6.2 GHz). In addition, the achieved radiation efficiency was 90%. Consistent and almost invariant radiation patterns are achieved over the millimetre-wave frequency band of interest. The experimental and simulated results are in good agreement, justifying the feasibility of the proposed design as a high-gain and wideband FP resonator array antenna for Mm-wave applications.