Evaluation of Diffuse Reflection Infrared Spectrometry for End-of-Shift Measurement of α-quartz in Coal Dust Samples.

The inhalation of toxic substances is a major threat to the health of miners, and dust containing respirable crystalline silica (α-quartz) is of particular concern, due to the recent rise in cases of coal workers' pneumoconiosis and silicosis in some U.S. mining regions. Currently, there is no field-portable instrument that can measure airborne α-quartz and give miners timely feedback on their exposure. The U.S. National Institute for Occupational Safety and Health (NIOSH) is therefore conducting studies to investigate technologies capable of end-of-shift or real-time measurement of airborne quartz. The present study focuses on the potential application of Fourier transform infrared (FT-IR) spectrometry conducted in the diffuse reflection (DR) mode as a technique for measuring α-quartz in respirable mine dust. A DR accessory was used to analyze lab-generated respirable samples of Min-U-Sil 5 (which contains more than 90% α-quartz) and coal dust, at mass loadings in the ranges of 100-600 µg and 600-5300 µg, respectively. The dust samples were deposited onto three different types of filters, borosilicate fiberglass, nylon, and polyvinyl chloride (PVC). The reflectance, R, was calculated by the ratio of a blank filter and a filter with deposited mine dust. Results suggest that for coal and pure quartz dusts deposited on 37 mm PVC filters, measurements of -log R correlate linearly with known amounts of quartz on filters, with R(2) values of approximately 0.99 and 0.94, respectively, for samples loaded up to ∼4000 µg. Additional tests were conducted to measure quartz in coal dusts deposited onto the borosilicate fiberglass and nylon filter media used in the NIOSH-developed Personal Dust Monitor (PDM). The nylon filter was shown to be amenable to DR analysis, but quantification of quartz is more accurate when the filter is "free," as opposed to being mounted in the PDM filter holder. The borosilicate fiberglass filters were shown to produce excessive interference, making quartz quantification impossible. It was concluded that, while the DR/FT-IR method is potentially useful for on-filter measurement of quartz in dust samples, the use of PVC filters produced the most accurate results.

Anterior Cruciate Ligament Revision Reconstruction.

Revision anterior cruciate ligament (ACL) reconstruction is used in patients with recurrent instability after primary ACL reconstruction. Identifying the etiology of graft failure is critical to the success of revision reconstruction. The most common etiologies include technical errors, trauma, failure to recognize concomitant injuries, young age, incomplete rehabilitation, and hardware failure. Patients should undergo a complete history and physical examination with a specific focus on previous injury mechanism and surgical procedures. A revision ACL reconstruction is a technically demanding procedure, and the surgeon should be prepared to address bone tunnel osteolysis, concurrent meniscal, ligamentous, or cartilage lesions, and limb malalignment. Surgical techniques described in this article include both single-stage and two-stage reconstruction procedures. Rates of return to sport after a revision reconstruction are lower than after primary reconstruction. Future research should be focused on improving both single-stage and two-stage revision techniques, as well as concomitant procedures to address limb malalignment and associated injuries.

Determining the Ratio of Wedge Height to Degree of Correction for Anterior Tibial Closing Wedge Osteotomies for Excessive Posterior Tibial Slope.

BACKGROUND: Anterior closing wedge osteotomy of the proximal tibia may be considered in revision anterior cruciate ligament (ACL) reconstruction surgery for patients with excessive posterior tibial slope (PTS). PURPOSE: (1) To determine the ratio of wedge thickness to degrees of correction for supratubercle (ST) versus transtubercle (TT) osteotomies for anterior closing wedge osteotomies and (2) to evaluate the accuracy of ST and TT osteotomies in achieving slope correction. STUDY DESIGN: Controlled laboratory study. METHODS: The computed tomography (CT) scans of 38 knees in 37 patients undergoing revision ACL reconstruction were used to simulate both ST and TT osteotomies. A 10° wedge was simulated in all CT models. The height of the wedge along the anterior tibia was recorded for each of the 2 techniques. The ratio of wedge height to achieved degree of correction was calculated. ST and TT osteotomies were performed on 3-dimensional (3D)-printed tibias of the 12 patients from the study group with the greatest PTS, after the desired degree of correction was determined. Pre- and postosteotomy slopes were measured for each tibia, and the actual change in slope was compared with the intended slope correction. RESULTS: According to CT measurements, the ratio of wedge height to degree of correction was 0.99 ± 0.07 mm/deg for the ST osteotomy and 0.83 ± 0.06 mm/deg for the TT osteotomy (P < .001). When these ratios were used to perform simulated osteotomies on the twelve 3D-printed tibias, the mean slope correction was within 1° to 2° of the intended slope correction, regardless of osteotomy location (ST or TT) or whether slope was measured on the medial or lateral plateau. The ST technique tended to undercorrect and the TT technique tended to overcorrect. CONCLUSION: When anterior tibial closing wedge osteotomies were removed to correct excessive PTS, removing a wedge with a ratio of 1 mm of wedge height for every 1° of intended correction for an ST technique and a ratio of 0.8 mm to 1° for a TT technique resulted in overall average slope correction within 1° to 2° of the target. CLINICAL RELEVANCE: The calculated ratios will allow clinicians to more accurately correct PTS when performing anterior closing wedge tibial osteotomy.