Effect of bone size, not density, on the stiffness of the proximal part of normal and osteoporotic human femora.

Proximal femur fractures in the elderly lead to a high rate of hospitalization. In studying the operative treatment of such fractures, it is first necessary to understand the relationship between the morphologic properties of this part of the femur (related to both geometry and density) and its mechanical properties. Numerous investigations showed that femoral strength correlates with bone mass; however, the dimension of the bones was not taken into account. We measured the relationship between the stiffness of the proximal femur under physiologic load and its geometry and density. Conventional x-rays and quantitative computed tomography (QCT) were carried out on pairs of human cadaver femora. Eight pairs were instrumented with strain gauges. Bones were subjected to an eccentric load that simulates moderate weight bearing (single-leg stance), and the strain parallel to the bone axis was plotted as a function of the load applied. An apparent bone stiffness was calculated as the ratio between the strain gradient within the section and the load applied. Strong correlation was found between x-ray densitometry and QCT. The bone stiffness also correlates strongly with the geometry (area) and slightly with bone mass; however, an unexpectedly low correlation was found between stiffness and density. We chose stiffness as a mechanical parameter (not strength) because it describes the "normal" bone behavior under load. Our results clearly demonstrate that the cross-sectional size of the bones must be taken into account when establishing the relationship between the mechanical characteristics of the bone and its morphology. In accordance with previous predictions, our results support that bone loss due to osteoporosis is compensated for by an increase in bone diameter.

Laser Doppler flowmetry for bone blood flow measurement: correlation with microsphere estimates and evaluation of the effect of intracapsular pressure on femoral head blood flow.

Laser Doppler flowmetry (LDF) was used to measure bone blood flow in the rabbit femoral head and femoral condyles. To correlate the LDF output signal blood cell flux to in vivo blood flow, simultaneous measurements using LDF and 85Sr-labeled microspheres were made in an adult rabbit model. There was no correlation between the two methods for blood flow in the femoral condyles and the correlation between the two methods for blood flow in the femoral head does not achieve statistical significance. An LDF signal of 0.4 V was approximately equal to a microsphere measured flow rate of 0.4 ml blood/g bone/min. The strength of the correlation in the latter case may have been affected by (a) large arteriovenous shunts, (b) inadequate mixing of the microspheres with a left ventricular injection, and (c) insufficient numbers of microspheres present in the bone samples with which to satisfy the mathematical requirements of the microsphere method. When LDF was used to evaluate the effect of elevated intracapsular pressure on femoral head blood flow in skeletally mature rabbits, femoral head subchondral bone blood flow declined with increasing intracapsular pressure from a baseline value of 0.343 +/- 0.036 to a value of 0.127 +/- 0.27 at 120 cm of water pressure. The decline in femoral head blood flow was statistically significant at pressures of 40 cm of water or higher (p less than 0.001), and evaluation of sections of the proximal femora made from preterminal disulphine blue injections confirmed these findings. Intracapsular tamponade has an adverse effect on femoral head blood flow beginning well below central venous pressure and should be considered in the pathophysiology of posttraumatic and nontraumatic necrosis of the femoral head. Laser Doppler flowmetry was easy to use and appears to be a reproducible technique for evaluating femoral head blood flow, offering distinct advantages over the microsphere technique for measuring bone blood flow. Further studies of the in vivo calibration of the LDF method for bone blood flow are necessary for the method to have potential for clinical application.

Histology of the alar and transverse ligaments.

Seven sets of human transverse and alar ligaments, after tensile testing, and eight corresponding ligaments without testing, were examined histologically with respect to their fiber composition and fiber orientation. Various staining techniques were supplemented by polarized light microscopy. Both the transverse and the alar ligaments consist of collagen fibers, with very few elastic fibers in the peripheral layer. In the central portion of the transverse ligament, the collagen fibers cross each other at an angle of approximately 30 degrees. Close to the dens, the transverse ligaments show on their ventral side a transition into fibrocartilage. Except for the immediate site of failure, no differences became evident between tested specimens and controls. The collagen, as the almost exclusive constituent, together with the fiber orientation determine the mechanical properties of these ligaments. This supports the hypothesis that the ligaments could be irreversibly overstretched or even ruptured when the head is rotated and, in addition, flexed by impact trauma, especially in unexpected rear-end collisions.

A paradigm of delayed union and nonunion in the lumbosacral joint. A study of motion and bone grafting of the lumbosacral spine in sheep.

In a group of nine sheep (Group A), it was noted that when small, interlocking cancellous and cortical cancellous bone grafts are placed posteriorly on the lumbosacral spine, union always occurred in the interlumbar motion segments and almost never occurred at the lumbosacral joint. One of the main differences in these two areas is the amount of motion that occurs at each level with flexion and extension. Because nonunion following bone grafting for arthrodesis of the spine is a serious clinical problem, we have studied the amount of motion seen at the interlumbar and lumbosacral joints in sheep to ascertain how much motion is compatible with union and how much is associated with nonunion. In vivo studies were carried out in eight sheep (Group B), and five normal spine segments were studied in vitro to determine normal motion in this species. To simplify the complex in vivo motion that occurs at the lumbar motion segments, the simple linear displacement and strain of the fusion mass (consisting of fibrous tissue and bone grafts placed on and between the laminas posteriorly) was measured with the spine in flexion and extension. When the displacement and strain at the interlaminar level of the L6-S1 joint was measured, the linear displacement was found to be 5.2 mm and the associated linear strain 36%. The displacement at the L5-L6 interspace was 1.2 mm, and the strain 10%. The stiffness of the L5-L6 joint (which always fused) and the L6-S1 joint (which did not fuse, with one exception) were also studied. In a third group of four animals (Group C), internal fixation of the lumbosacral joint was attempted in addition to bone grafting.(ABSTRACT TRUNCATED AT 250 WORDS)

Bone growth and remodelling after fracture.

We used a rabbit model to investigate the mechanism by which the angulation of fractures is corrected in children. We produced a transverse proximal tibial fracture in one leg of 12 eight-week-old New Zealand white rabbits and measured bone alignment and length and the patterns of bone growth and remodelling. The angle between the joint surfaces changed rapidly to correct the alignment of the limb as a result of asymmetrical growth of epiphyseal plates. In an adult with closed plates, the angle between the joint surfaces cannot therefore improve. The angle at the fracture itself showed slow improvement because of bone drift and the asymmetrical growth of the epiphyseal plates. Remodelling corrected the shape of the bone in the region of the fracture. Periosteal division on the convex side increased the growth of the epiphyseal plate on that side, thus slowing the correction. The effect was relatively small, providing an indication that factors other than the periosteum are important in inducing correction. External torsional deformities developed because of helical growth at the plate. This was probably caused by abnormal posture which induced a torque at the growth plate. Helical growth is the mechanism by which rotational deformities can occur and correct.

Theoretical considerations in rigid fixation of facial bones.

The classic facial fracture patterns have gradually been changing toward more severe comminutions. This necessitates an early and accurate anatomical reduction and a fixation in this position until the fragments have united. Stable fixation favors early mineralization in the fracture gap. The mechanical function of the implants is thus only needed for a short term. Similar considerations are true for the incorporation of grafts. Mechanics of fixation of facial bones is influenced by the structural properties as well.

Comparison of compression and torque measurements of self-tapping and pretapped screws.

The choice of an internal fixation system for maxillofacial surgery is made difficult because of lack of information with respect to functional load. This study attempted to clarify some of the controversy with respect to maxillofacial use of these implants. Maximal compressive force to torque values were measured in standardized bone thicknesses of 1, 2, 3, and 4 mm. The screws tested were pretapped AO 1.5-, 2.0-, 2.7-, and 3.5-mm rescue screws and self-tapping Luhr, Champy, and AO 1.5- and 2.0-mm screws. Ten measurements were made for each screw type/bone thickness combination using a piezoelectric washer and torque screwdriver. It was apparent that for 1- and 2-mm bone thicknesses the use of self-tapping screws resulted in the highest compression values. In 3- and 4-mm bone thicknesses, pretapped screws offered the highest compression values. As expected, self-tapping screws had the highest torque values on insertion owing to torque loss in cutting the screw threads. The 2.7-mm screw offered no advantage over the 2.0-mm screws in 1- and 2-mm bone thicknesses but resulted in higher compression values in 3- and 4-mm bone thicknesses.

Fixation effects on membranous and endochondral onlay bone graft revascularization and bone deposition.

This paper investigates the relationship between bone resorption, the process of bone revascularization, and graft fixation. Vital staining techniques and microangiography were used to study the extent of graft revascularization of fixed and nonfixed endochondral (rib) and membranous (skull) onlay bone grafts in 20 adult sheep mandibles bilaterally. This assessment was carried out at 2 and 20 weeks postoperatively. Sequential fluorochrome staining was performed to examine the pattern of new bone deposition. Fixation was achieved using the lagscrew technique. At 2 weeks, membranous bone demonstrated a greater area of graft revascularization if fixed than if the graft was not fixed. The opposite result was seen for endochondral grafts, where nonfixed grafts showed a greater area of revascularization than fixed grafts. At 20 weeks, all bone that was present was fully vascularized. The inconsistencies in the results on the relationship between fixation and revascularization for membranous and endochondral grafts in the early stages of healing (2 weeks) suggest that although revascularization is a necessary precondition for bone resorption and deposition, biomechanical and structural factors may be a more satisfactory explanation for the differences observed in the maintenance of bony volume.

Fixation effects on membranous and endochondral onlay bone-graft resorption.

Difficulties arise in the prediction of maintenance of graft volume over time when bone grafts are used for facial contour reconstruction. We hypothesize that graft fixation will decrease movement and lead to decreased resorption. Fixed and nonfixed endochondral (rib) and membranous (skull) onlay bone grafts measuring 30 X 10 X 4 mm were grafted to the mandible bilaterally in 10 adult sheep. Fixation was achieved using the lag-screw technique. Volume measurements using caliper technique were made 20 weeks postoperatively. The volume of graft present at 20 weeks was significantly greater for the fixed bone grafts (p less than 0.001): fixed membranous, 85.9 percent; fixed endochondral, 76.2 percent; nonfixed membranous, 55 percent; and nonfixed endochondral, 16.6 percent. The results are explained using biomechanical theories related to the effects of strain. At present, it is suggested by this study that when onlay bone grafts are stabilized, improved results with respect to graft resorption can be expected.

Fixation of vascularized bone grafts.

In 24 patients, fixation of isolated or combined bone grafts has been performed exclusively with miniplates. Other than the lateral displacement of one osteomyocutaneous iliac crest graft, no complication occurred with regard to the fixation method chosen. In contrast to the clinical findings, our results of an animal experiment demonstrate less complications by fixation of vascularized bone grafts to mandibular angle defects (guinea pig) when THORP plates are used instead of miniplates. Whereas we consider miniplate fixation of vascularized bone grafts to be the method of choice, selected patients may require more stable fixation systems, especially when a high postoperative mobility may be expected or large amounts of the mandible including the condyle have to be reconstructed.

The use of miniplates in mandibular fractures. An in vitro study.

To test the stability of miniplate osteosynthesis in the mandible, a three-dimensional in vitro model was developed. Four clinically relevant fracture situations were simulated by osteotomies in polyurethane mandibles. The stability of the osteosyntheses was tested according to a reproducible procedure of unilateral loading under conditions of static equilibrium. The mandible was supported at the condyles in silicon rubber fossae and was held in position by traction on the coronoid processes in combination with preloading in the region of the incisors with a force of 10 N. Six points were tested to register the effects of unilateral loading on bending and torsion at the sites of the osteotomies. The following results were obtained. The preliminary results show that in cases of jaw angle fracture neither bending nor torsional forces are sufficiently controlled by miniplate-fixation in the commonly proposed position. Furthermore, it was confirmed that fracture treatment in the canine region requires two plates instead of one to resist displacement of the fracture fragments during function.

Fixation with reconstruction plates under critical conditions: the role of screw characteristics.

Mandibular angular ostectomy defects in 12 sheep were bridged with a titanium plate system (THORP), designed according to the screw-plate-locking principle. Two screw designs (hollow and solid) and two rough (plasma-coated, sand-blasted)-surface and one smooth (anodized)-surface structure were tested in a critical two-screw anchorage model. Fixation with two screws only per fragment was successful in only one-third of the cases. The fixation results were superior for screws with a rough surface, either sand-blasted or plasma-coated. The hollow-screw design did not seem to offer special advantages over the solid screws with identical surface structure. In the successful cases, the bone-screw contact was maintained continuously over a period of 8 weeks, and anchorage was even enhanced by reinforcement of the cancellous structures. In the unsuccessful cases, peri-implant bone resorption seemed to be related to jeopardized bone perfusion in the vicinity of the implants. It is presumed that a plating system with locked screws has the advantage that only two screws will hold a relatively short condylar process. This study proved the assumption to be questionable. However, in view of the problems related to prosthetic replacement of the temporomandibular joint, an attempt to salvage the articular portion may still be justified in selected cases, even if the chance of success is as low as 30%.

The role of corticotomy and osteotomy in the treatment of bone defects using the Ilizarov technique.

Posttraumatic bone defects are usually bridged using autogenous or exogenous cancellous bone grafts. These grafts consolidate to form a solid bone structure that is mechanically stiffer than natural bone. Likewise, the procedure of corticotomy and distraction is appropriate for treatment of bone defects. In our experiment, a 2-cm bone defect was created in 25 sheep tibiae. We performed corticotomy or osteotomy of the intact bone, thus creating a bone segment that was drawn across the defect using a specially designed traction device. The limb was stabilized using an external fixator. Four groups were formed for comparison: corticotomy and osteotomy with distraction at a rate of 1 mm/day; corticotomy and osteotomy with immediate transportation of the segment to the docking site. The animals were killed after 4, 8, 12, 16 and 52 weeks. Evaluation of the results was based on standard radiographs. In the two groups involving gradual transportation, spontaneous bone regeneration occurred in all cases whereby after corticotomy the new bone was tubular (around the medulla). Following osteotomy, bone regeneration occurred initially on the dorsal and lateral sides of the tibia leaving a defect on the ventral and medial sides. This defect subsequently closed. At the end of segment transportation, healing was observed at the docking site. In Groups 3 and 4, the bone did not regenerate at all. Therefore, this procedure, immediate transportation, was not investigated further because no clinical success could be expected from its application.

Autogenous cancellous bone graft incorporation in a gap defect in the canine femur.

While gap defect models provide greater graft stability and are more representative of many clinical situations than segmental defect models, the healing in these models has not been well documented. To study the histologic course of cancellous bone graft healing in a long bone gap defect, 12 adult mongrel dogs were killed in groups of two at 1, 2, 3, 4, 6, and 12 weeks. Graft incorporation in these dogs was studied using macro- and microradiography, histologic sections, and computer-assisted digital surface analysis; results are described. Unlike that seen in segmental defect models, the pattern of repair in a cancellous bone grafted gap defect provides consistent healing at 12 weeks and follows the same healing process seen with stable defects.

High pressure pulsatile lavage irrigation of intraarticular fractures: effects on fracture healing.

OBJECTIVES: To evaluate the effects of pulsatile lavage and bulb syringe irrigation on fracture healing in vivo. DESIGN: Randomized prospective trial in an animal model. SETTING: Medical school orthopaedic department. SUBJECTS: Thirty New Zealand white rabbits. INTERVENTION: The control group (C) underwent osteotomy of the medial femoral condyle, stabilization, and closure. The bulb syringe and pulsatile lavage groups underwent the same procedure as group C, with the addition of irrigation with one liter of normal saline via a bulb syringe (B) or a pulsatile lavage system (P). Animals were administered two fluorescent bone stains: xylenol orange at the time of operation, and calcein green one week postoperatively. Animals were euthanized two weeks postoperatively and femurs were retrieved for histological analysis. MAIN OUTCOME MEASURES: Union was determined by examination of microradiographs under light microscopy. The viability of bone along the fracture site was determined by evaluation of xylenol orange and calcein green staining under fluorescent microscopy. The density of new bone formed in the osteotomy site was assessed by computerized digitization of standardized regions of the proximal and distal osteotomy. RESULTS: Xylenol orange bands were present a mean of 66 +/- 8 percent (mean +/- standard error of the mean), 65 +/- 6 percent, and 44 +/- 5 percent of the distance along the osteotomy in groups C, B, and P, respectively (p < 0.001). Calcein green bands were present throughout the osteotomy site in all specimens. Calcified new bone was present in 62 +/- 4 percent, 58 +/- 7 percent, and 41 +/- 9 percent of the area measured in groups C, B, and P, respectively (p = 0.07). Twenty percent of the osteotomies in groups C and B did not unite, compared with 30 percent in group P (p > 0.5). CONCLUSIONS: Pulsatile lavage irrigation of fresh intraarticular fractures in rabbits has a detrimental effect on early new bone formation; this effect, however, is no longer apparent two weeks following irrigation. While this study evaluated the effects of pulsatile lavage irrigation in noncontaminated fractures without extensive soft tissue injury, the detrimental effects observed on early new bone formation may translate to an increased risk of nonunion in the setting of a contaminated open fracture with extensive soft tissue injury. Based on the results of this investigation, the selective use of pulsatile lavage irrigation appears warranted. In the absence of gross wound contamination, irrigation with a bulb syringe appears less likely to impair fracture healing than does pulsatile lavage irrigation. Expansion of the model used in this study to include bacterial contamination and soft tissue crushing may further elucidate the effects of pulsatile lavage irrigation on fracture healing.

The effect of radial preload on the implant-bone interface: a cadaveric study.

The most common complication of external fixation is pin loosening. Preloading the implant-bone interface is believed to retard this process. Radial preload, in particular, may be useful, as it allows loading in more than one direction. To investigate the effect of varying degrees of radial preload on the pin-bone interface, 30 freshly thawed human cadaveric tibiae were sectioned into 4-cm segments. Uniform drill holes were produced in the anterior tibial ridge of all segments and custom experimental bolts, oversized in diameter by as much as 1 mm, were pressed into each specimen. Macroscopic surface fractures were noted at the time of bolt insertion for misfits greater than 0.2 mm. Following histologic preparation, the implant-bone interface was evaluated microscopically based on the appearance of osteonal compression, lamellar distortion, and microfractures. Insertion of external fixator pins with misfits of greater than 0.4 mm resulted in significant microscopic structural damage to the bone surrounding the pin. High degrees of radial preload, exceeding the elastic limit of cortical bone, may be produced around pin holes by a small misfit. The use of oversized pins or screws must therefore be questioned.

Direct and indirect bone healing after operative fracture treatment.

The knowledge of the entire spectrum of differing healing patterns should help the surgeon to judge the progress of fracture healing. To be able to recognize an abnormal course and deviating patterns will help the surgeon to avoid risks and to improve the mechanical and biologic conditions necessary for successful fracture treatment.

[Fat embolism and fracture, a review of the literature]. / Fettembolie und Fraktur, eine Literaturübersicht.

The reasons of fat embolism as well as the following fat embolism syndrome are most likely long bone fractures, especially if the femur is participated. On the other hand there are cases, where a severe concussion of the entire body caused fat embolism. But it is also supposed, that intramedullary reaming as well as the insertion of knee- and hip-prostheses could be a releasing factor, because the applicated pressure on the medullary canal can cause a fat release in the systemic blood system. The morbidity depends on age and fracture, which is on fractures between 0.9 and 2%. The most affected group are people between 18 and 28 years of age. The fat embolism is manifesting at 46-60% of the patients in the first 24 hours and over 90% of the patients are affected in the first three days. If you look at the metabolic changes, you will find shortly after the fracturing process a rapid increase of free fatty acids (FFA), as well as an increase of the plasmatic enzyme levels (lipase, GPT, GOT, GLDH, LDH, etc.), catecholamines and glucocorticoids. In order to discuss the pathogenesis in a fairly complete way, you have to take different theories into consideration, because several parallel running processes--which are influencing each other--are leading to the syndrome. Infloating theory: Proceeding on the assumption that contents of the bone marrow are floating out of the fracture gap into the venous system and are leading to fat embolism in the lungs. Lipase theory: You can diagnose in 50-70% of the fracture patients an increase of the lipase level, which is correlating with the manifestation of the fat embolism. The lipase releases fat from the body depositories in addition to the fat, who is coming out of the fracture gap. Shock and coagulation theory: During shock the microcirculation is decelerated, the blood viscosity is increased and the suspension stability of the cellular blood components is decreased, which is leading to the sludging phenomenon. So the capillaries of the lungs and the brain are a kind of sludge filter of the blood, that is changed in its suspensions stability. Free fatty acids theory: Primary existing capillary defects are reasonable caused by free fatty acids (FFA). They are hydrolyzed of the neutral fats and are histotoxic for the walls of the blood vessels.(ABSTRACT TRUNCATED AT 400 WORDS)

[Area of contact between osteosynthesis plate and bone in internal fixation (author's transl)]. / Kontaktfläche zwischen Osteosyntheseplatte und Knochen.

The bone can be protected against excessive stress if the plate is properly adapted to the surface of the contact area between plate and bone, thus ensuring good and longlasting repositioning of the fracture. The article describes an in-vitro method for the quantitative evaluation of the contact area between plate and bone in osteosynthesis. With four different bones and the requisite plates, six expert surgeons were able to obtain an area of contact between plate and bone which varied between 13 and 60%, the average being 32%. The available data allow us to conclude that the peak loads of pressure occurring with small contact areas may be so great that they exceed the maximum compressive strength of the bone.