Cold Storage of Human Femoral Arteries for Twelve Months: Impact on Mechanical Properties.

OBJECTIVE: This biomechanical pre-clinical study aimed to assess the consequences on mechanical properties of long term cold storage (+2 to +8 °C) of arterial allografts. METHODS: Femoropopliteal arterial segments were collected from multiorgan donors and stored at +2 to +8 °C for twelve months in saline solution with added antibiotics. Mechanical characterisation was carried out using two different tests, with the aim of defining the physiological modulus and the maximum stress and strain borne by the sample before rupture. These characterisations were carried out after zero, six, and twelve months of storage for each sample (T0, T6, and T12, respectively). For comparison, the same tests were performed on cryopreserved femoropopliteal segments after thawing. RESULTS: Twelve refrigerated allografts (RAs), each divided into three segments, and 10 cryopreserved allografts (CAs) were characterised. The median (interquartile range [IQR]) Young's modulus was not statistically significantly different between the storage times for cold stored allografts: RAT0, 164 (150, 188) kPa; RAT6, 178 (141, 185) kPa; RAT12, 177 (149, 185) kPa. The median (IQR) Young's modulus of the CA group (153; 130, 170 kPa) showed no significant differences from the RA groups, irrespective of storage time. Furthermore, median (IQR) maximum stress and strain values were not significantly different between the different groups: for maximum stress: RAT0, 1.58 (1.08, 2.09) MPa; RAT6, 1.74 (1.55, 2.36) MPa; RAT12, 2.25 (1.87, 2.53) MPa; CA, 2.25 (1.77, 2.61) MPa; and for maximum strain: RAT0, 64% (50, 90); RAT6, 79% (63, 84); RAT12, 72% (65, 86); CA, 67% (50, 95). CONCLUSION: Cold storage for up to twelve months appears to have no impact on the mechanical characteristics of human arterial allografts. Therefore, this preservation method, which would greatly simplify routine care, seems feasible. Other indicators are being studied to verify the safety of this preservation process before considering its use in vivo.

Time-Temperature Superposition Principle in Shearing Tests Compared to Tension Conditions for Polymers Close to Glass Transition.

The well-known principle of time-temperature superposition (TTS) is of prime interest for polymers close to their glass transition. First demonstrated in the range of linear viscoelasticity, it has been more recently extended to large deformations in tension. However, shear tests were not yet addressed. The present study depicted TTS in shearing conditions and compared it to results in tensile conditions both for low and high strains for a polymethylmethacrylate (PMMA) of different molar masses. The main objectives were to enlighten the relevance of the principle of time-temperature superposition for shearing at high strain and to discuss the way shift factors should be determined. It was suggested that shift factors could be dependent on compressibility, which should be taken into account when addressing various types of complex mechanical loadings.

Molten-State Dielectrophoretic Alignment of EVA/BaTiO3 Thermoplastic Composites: Enhancement of Piezo-Smart Sensor for Medical Application.

Dielectrophoresis has recently been used for developing high performance elastomer-based structured piezoelectric composites. However, no study has yet focused on the development of aligned thermoplastic-based piezocomposites. In this work, highly anisotropic thermoplastic composites, with high piezoelectric sensitivity, are created. Molten-state dielectrophoresis is introduced as an effective manufacturing pathway for the obtaining of an aligned filler structure within a thermoplastic matrix. For this study, Poly(Ethylene-co Vinyl Acetate) (EVA), revealed as a biocompatible polymeric matrix, was combined with barium titanate (BaTiO3) filler, well-known as a lead-free piezoelectric material. The phase inversion method was used to obtain an optimal dispersion of the BaTiO3 within the EVA thermoplastic matrix. The effect of the processing parameters, such as the poling electric field and the filler content, were analyzed via dielectric spectroscopy, piezoelectric characterization, and scanning electron microscopy (SEM). The thermal behavior of the matrix was investigated by thermogravimetric analysis (TGA) and differential scanning calorimetry analysis (DSC). Thermoplastic-based structured composites have numerous appealing advantages, such as recyclability, enhanced piezoelectric activity, encapsulation properties, low manufacturing time, and being light weight, which make the developed composites of great novelty, paving the way for new applications in the medical field, such as integrated sensors adaptable to 3D printing technology.

Measurement and comparison of dielectric properties of human pancreatic tumours, healthy tissues and porcine tissues ex vivo between 1Hz and 1MHz.

The dielectric properties of pancreatic tissues from human healthy and tumour-bearing tissues have been extracted from impedance measurement on ex vivo, freshly excised samples. They are compared to pig pancreas samples, measured following the same protocol. The purpose is to add data to the scarce literature on the properties of the human pancreas and pancreatic tumours, for treatment planning, tissue identification and numerical simulations. The conductivity measured at 500 kHz for human healthy pancreas is 0.26 S/m, while the conductivity of tumour-bearing tissues is 0.44 S/m. Those values differ significantly from that listed in the IT IS database at 0.57 S/m, suggesting an update might be to consider. However, measures of relative permittivity are in accordance with the database with a value of approximately 2.3x103. Ex vivo porcine model, while being less conductive than human pancreas with 0.16 S/m at the same frequency, is deemed a relevant model when studying pancreatic applications of electromagnetic fields-based treatments, such as radiofrequency ablation.

Viscoelastic Properties of Polypropylene during Crystallization and Melting: Experimental and Phenomenological Modeling.

This paper deals with the viscoelastic behavior during crystallization and melting of semicrystalline polymers, with the aim of later modeling the residual stresses after processing in cases where crystallization occurs in quasi-static conditions (in additive manufacturing for example). Despite an abundant literature on polymer crystallization, the current state of scientific knowledge does not yet allow ab initio modeling. Therefore, an alternative and pragmatic way has been explored to propose a first approximation of the impact of crystallization and melting on the storage and loss moduli during crystallization-melting-crystallization cycles. An experimental approach, combining DSC, optical microscopy and oscillatory shear rheology, was used to define macroscopic parameters related to the microstructure. These parameters have been integrated into a phenomenological model. Isothermal measurements were used to describe the general framework, and crystallization at a constant cooling rate was used to evaluate the feasibility of a general approach. It can be concluded that relying solely on the crystalline fraction is inadequate to model the rheology. Instead, accounting for the microstructure at the spherulitic level could be more useful. Additionally, the results obtained from the experiments help to enhance our understanding of the correlations between crystallization kinetics and its mechanical effects.

Haptic Feedback Device Using 3D-Printed Flexible, Multilayered Piezoelectric Coating for In-Car Touchscreen Interface.

This study focuses on the development of a piezoelectric device capable of generating feedback vibrations to the user who manipulates it. The objective here is to explore the possibility of developing a haptic system that can replace physical buttons on the tactile screen of in-car systems. The interaction between the user and the developed device allows completing the feedback loop, where the user's action generates an input signal that is translated and outputted by the device, and then detected and interpreted by the user's haptic sensors and brain. An FEM (finite element model) via ANSYS multiphysics software was implemented to optimize the haptic performance of the wafer structure consisting of a BaTiO3 multilayered piezocomposite coated on a PET transparent flexible substrate. Several parameters relating to the geometric and mechanical properties of the wafer, together with those of the electrodes, are demonstrated to have significant impact on the actuation ability of the haptic device. To achieve the desired vibration effect on the human skin, the haptic system must be able to drive displacement beyond the detection threshold (~2 µm) at a frequency range of 100-700 Hz. The most optimized actuation ability is obtained when the ratio of the dimension (radius and thickness) between the piezoelectric coating and the substrate layer is equal to ~0.6. Regarding the simulation results, it is revealed that the presence of the conductive electrodes provokes a decrease in the displacement by approximately 25-30%, as the wafer structure becomes stiffer. To ensure the minimum displacement generated by the haptic device above 2 µm, the piezoelectric coating is screen-printed by two stacked layers, electrically connected in parallel. This architecture is expected to boost the displacement amplitude under the same electric field (denoted E) subjected to the single-layered coating. Accordingly, multilayered design seems to be a good alternative to enhance the haptic performance while keeping moderate values of E so as to prevent any undesired electrical breakdown of the coating. Practical characterizations confirmed that E=20 V/µm is sufficient to generate feedback vibrations (under a maximum input load of 5 N) perceived by the fingertip. This result confirms the reliability of the proposed haptic device, despite discrepancies between the predicted theory and the real measurements. Lastly, a demonstrator comprising piezoelectric buttons together with electronic command and conditioning circuits are successfully developed, offering an efficient way to create multiple sensations for the user. On the basis of empirical data acquired from several trials conducted on 20 subjects, statistical analyses together with relevant numerical indicators were implemented to better assess the performance of the developed haptic device.