Emergency Radiobioassay Method for Determination of 9°Sr and ²²6Ra in a Spot Urine Sample.

A new radiobioassay method has been developed for simultaneous determination of (90)Sr and (226)Ra in a spot urine sample. The method is based on a matrix removal procedure to purify the target radionuclides from a urine sample followed by an automated high performance ion chromatographic (HPIC) separation of (90)Sr and (226)Ra and offline radiometric detection by liquid scintillation counting (LSC). A Sr-resin extraction chromatographic cartridge was used for matrix removal and purification of (90)Sr and (226)Ra from a urine sample prior to its introduction to the HPIC system. The HPIC separation was carried out through cation exchange chromatography using methanesulfonic acid (75 mM) as the mobile phase at 0.25 mL/min flow rate. The performance criteria of the method was evaluated against the American National Standard Institute ANSI/HPS N13.30-2011 standard for the root mean squared error (RMSE) of relative bias (Br) and relative precision (SB) at two different spiked activity levels. The RMSE of Br and SB for (90)Sr and (226)Ra were found to be satisfactory (≤0.25). The minimum detectable activity (MDA) of the method for (90)Sr and (226)Ra are 2 Bq/L and 0.2 Bq/L, respectively. The MDA values are at least 1/10th of the concentrations of (90)Sr (190 Bq/L) and (226)Ra (2 Bq/L) excreted in urine on the third day following an acute exposure (inhalation) that would lead to an effective dose of 0.1 Sv in the first year. The sample turnaround time is less than 8 h for simultaneous determination of (90)Sr and (226)Ra.

An HPLC-ICP-MS technique for determination of cadmium-phytochelatins in genetically modified Arabidopsis thaliana.

A reversed-phase high-performance liquid chromatographic technique was developed to separate cadmium-phytochelatin complexes (Cd-PC2, Cd-PC3, and Cd-PC4) of interest in the plant Arapidopsis thaliana. High-performance liquid chromatography (HPLC) was coupled to an inductively coupled plasma mass spectrometric (ICP-MS) system with some modification to the interface. This was done in order to sustain the plasma with optimum sensitivity for cadmium detection in the presence of the high methanol loads used in the gradient elution of the reversed-phase separation. The detection limits were found to be 91.8 ngl(-1), 77.2 ngl(-1) and 49.2 ngl(-1) for Cd-PC2, Cd-PC3, and Cd-PC4 respectively. The regression coefficients (r2) for Cd-PC2 to Cd-PC4 detection ranged from 0.998 to 0.999. The method was then used to investigate the occurrence and effect of cadmium-phytochelatin complexes in wild-type Arabidopsis and a phytochelatin-deficient mutant cad1-3 that had been genetically modified to ectopically express the wheat TaPCS1 phytochelatin synthase enzyme. The primary complex found in both wild-type and transgenic plants was Cd-PC2. In both lines, higher levels of Cd-PC2 were found in shoots than in roots, showing that phytochelatin synthases contribute to the accumulation of cadmium in shoots, in the Cd-PC2 form. Genetic modification did, however, impact the overall accumulation of Cd. Transgenic plants contained almost two times more cadmium in the form of Cd-PC2 in their roots than did the corresponding wild-type plants. Similarly, the shoot samples of the modified species also contained more (by 1.6 times) cadmium in the form of Cd-PC2 than the wild type. The enhanced role of PC2 in the transgenic Arabidopsis correlates with data showing long-distance transport of Cd in transgenic plants. Targeted transgenic expression of non-native phytochelatin synthases may contribute to improving the efficiency of plants for phytoremediation.

Analysis of phosphorus herbicides by ion-pairing reversed-phase liquid chromatography coupled to inductively coupled plasma mass spectrometry with octapole reaction cell.

A reversed phase ion-pairing high performance liquid chromatographic (RPIP-HPLC) method is developed for the separation of two phosphorus herbicides, Glufosinate and Glyphosate as well as Aminomethylphosphonic acid (AMPA), the major metabolite of Glyphosate. Tetrabutylammonium hydroxide is used as the ion-pairing reagent in conjunction with an ammonium acetate/acetic acid buffering system at pH 4.7. An inductively coupled plasma mass spectrometer (ICP-MS) is coupled to the chromatographic system to detect the herbicides at m/z = 31P. Historically, phosphorus has been recognized as one of the elements difficult to analyze in argon plasma. This is due to its relatively high ionization potential (10.5 eV) as well as the inherent presence of the polyatomic interferences 14N16O1H+ and 15N16O+ overlapping its only isotope at m/z = 31. An octapole reaction cell is utilized to minimize the isobaric polyatomic interferences and to obtain the highest signal-to-background ratio. Detection limits were found to be in the low ppt range (25-32 ng/l). The developed method is successfully applied to the analysis of water samples collected from the Ohio River and spiked with a standard compounds at a level of 20 microg/l.

An emergency radiobioassay method for 226Ra in human urine samples.

A new radioanalytical method was developed for rapid determination of (226)Ra in human urine samples. The method is based on organic removal and decolourisation of a urine sample by a polymeric (acrylic ester) solid phase sorbent material followed by extraction and preconcentration of (226)Ra in an organic solvent using a dispersive liquid-liquid microextraction technique. Radiometric measurement of (226)Ra was carried out using a liquid scintillation counting instrument. The minimum detectable activity for the method (0.15 Bq l(-1)) is lower than the required sensitivity of 0.2 Bq l(-1) for (226)Ra in human urine samples as defined in the requirements for radiation emergency bioassay techniques for the public and first responders based on the dose threshold for possible medical attention recommended by the International Commission on Radiological Protection (ICRP). The accuracy (expressed as relative bias, B(r)) and repeatability of the method (expressed as relative precision, S(B)) evaluated at the reference level (2 Bq l(-1)) were found to be -4.5 and 2.6 %, respectively. The sample turnaround time was <5 h for a single urine sample and <20 h for a batch of six urine samples. With the fast sample turnaround time combined with the potential to carry out the analysis in a field deployable mobile laboratory, the newly developed method can be used for emergency radiobioassay of (226)Ra in human urine samples following a radiological or nuclear accident.

Metabolism of 210Po in rats: volatile 210Po from faeces.

The metabolic formation of volatile (210)Po species in a rat that was intravenously administered with (210)Po-citrate was investigated in this study. A slurry of the faecal sample was prepared in water and was bubbled with nitrogen gas in a closed system. The discharged gas was passed through a trapping device filled with liquid scintillation cocktail in order to capture any volatile (210)Po species. The amount of (210)Po trapped in the scintillation cocktail was measured by a liquid scintillation analyser that provided evidence of the presence of volatile (210)Po species in the faeces. The presence of volatile (210)Po in the faeces indicates that the metabolic formation of volatile (210)Po is likely to occur in the gut due to bacterial activity. The amount of volatile (210)Po species was compared with the daily faecal excretion of (210)Po. After 2 h of bubbling, the volatile (210)Po collected from the faeces sample was found to be between 1.0 and 1.7 % of the daily faecal excretion for the 4 d following (210)Po-citrate administration.

Molecularly imprinted polymers for (90)Sr urine bioassay.

A molecularly imprinted polymer (MIP) comprising dicyclohexano-18-crown-6 (DCH18C6) was synthesized as a Sr-selective sorbent for urine bioassay purposes. MIP particles (326 ± 2 nm diameter) were formed using acetone and acetonitrile (1:3 v/v) as the porogen, methacrylic acid (MAA) as the functional monomer and ethylene glycol dimethacrylate (EGDMA) as the cross-linker. The DCH18C6-MIP particles were impregnated with additional DCH18C6 and treated further with NaOH to attain better binding affinity for Sr(2+). The effects of pH, ionic strength and amount of particles were evaluated for optimal extraction of (90)Sr(2+) from urine samples, as measured by liquid scintillation analysis (LSA). After up to 94% of (90)Y was removed by precipitation with TiO(2), DCH18C6-MIP particles were applied for selective SPE of (90)Sr remaining in the urine matrix for final LSA.

An emergency urine bioassay method for 241Am by extraction chromatography and liquid scintillation counting.

An emergency urine bioassay method has been developed for the determination of (241)Am in human urine samples. The method is based on extraction chromatographic separation of (241)Am from urine on a single DGA (N,N,N',N'-tetraoctyldiglycolamide) resin column followed by liquid scintillation counting of (241)Am. The minimum detectable activity (MDA) for the method was 0.02 Bq. Considering the volume of urine sample (17.2 ml) used by the method; the MDA was 1.3 Bq l(-1). Measurement accuracy (relative bias, B(r)) and repeatability (relative precision, S(B)) of the method were found to be -3.4 and 8.9 %, respectively, when urine samples were spiked with (241)Am (20 Bq l(-1)). Excellent linearity (r(2) > 0.999) was established over the range of 2-200 Bq l(-1). The method was also found to be robust (S(B)=10.2 %) against matrix effects from different urine samples. Performance of the rapid bioassay method for accuracy and repeatability were evaluated against the performance criteria for radiobioassay (ANSI N13.30) and found to be in compliance. Considering the simplicity, excellent analytical figures of merit and fast sample turnaround time (<1 h), it is a very promising rapid bioassay method for supporting the medical response to an emergency where internal contamination of (241)Am is involved.

A rapid bioassay method for the determination of 90Sr in human urine sample.

A rapid bioassay method has been developed for the determination of (90)Sr in human urine samples. The method is based on on-cartridge decolourisation of urine sample, separation of (90)Y from (90)Sr on an anion exchange resin column and by determination of (90)Sr using a liquid scintillation analyser (LSA). Separation of (90)Y from (90)Sr was achieved through selective complexation of yttrium with phosphate and subsequent retention of the anionic yttrium phosphate species on anion exchange resin. A total recovery of 97 +/- 2 % was obtained for strontium with three washes. The minimum detectable activity for the method was 0.2 Bq or 40 Bq l(-1). Measurement accuracy (relative bias, B(r)) and repeatability (relative precision, S(B)) of the method for the determination of (90)Sr were found to be -1 and 4.7 %, respectively. Excellent linearity (r(2) > 0.999) was established over an activity range from 3.25 x 10(2) to 3.25 x 10(4) Bq l(-1). The method was also found to be very robust (S(B) < 5 %) against the matrix effect from different urine samples. Performance of the rapid bioassay method for sensitivity, accuracy and repeatability evaluated against the performance criteria for radiobioassay (ANSI N13.30) was found to be in compliant. Considering the simplicity, excellent analytical figures of merit, fast sample turnaround time (<1 h) and cost efficiency (<30 USD per sample) of the developed method, it is very promising as a rapid bioassay method for supporting the medical response to an emergency where internal contamination of (90)Sr is involved.

Selectivity of 90Sr urine bioassay technique over 241Am, 238/239PU, 210PO, 137CS and 60CO.

The selectivity of a rapid (90)Sr bioassay technique over (241)Am, (238/239)Pu, (210)Po, (137)Cs and (60)Co has been investigated. Similar to (90)Sr, these radionuclides are likely to be used in radiological dispersive devices. The purpose of this study was to demonstrate the degree to which the (90)Sr bioassay technique is free from interference by these radionuclides if present in a urine matrix. The interfering radionuclides were removed (from (90)Sr) by their retention on an anion exchange column. While, recovery of the target radionuclide ((90)Sr) was found to be >or= 90 %, contributions from (241)Am, (242)Pu and (208)Po were found to be

Certification of a new selenized yeast reference material (SELM-1) for methionine, selenomethinone and total selenium content and its use in an intercomparison exercise for quantifying these analytes.

A new selenized yeast reference material (SELM-1) produced by the Institute for National Measurement Standards, National Research Council of Canada (INMS, NRC) certified for total selenium (2,059+/-64 mg kg(-1)), methionine (Met, 5,758+/-277 mg kg(-1)) and selenomethionine (SeMet, 3,431+/-157 mg kg(-1)) content is described. The +/-value represents an expanded uncertainty with a coverage factor of 2. SeMet and Met amount contents were established following a methanesulfonic acid digestion of the yeast using GC-MS and LC-MS quantitation. Isotope dilution (ID) calibration was used for both compounds, using 13C-labelled SeMet and Met. Total Se was determined after complete microwave acid digestion based on ID ICP-MS using a 82Se spike or ICP-OES spectrometry using external calibration. An international intercomparison exercise was piloted by NRC to assess the state-of-the-art of measurement of selenomethione in SELM-1. Determination of total Se and methionine was also attempted. Seven laboratories submitted results (2 National Metrology Institutes (NMIs) and 5 university/government laboratories). For SeMet, ten independent mean values were generated. Various acid digestion and enzymatic procedures followed by LC ICP-MS, LC AFS or GC-MS quantitation were used. Four values were based on species-specific ID calibration, one on non-species-specific ID with the remainder using standard addition (SA) or external calibration (EC). For total selenium, laboratories employed various acid digestion procedures followed by ICP-MS, AFS or GC-MS quantitation. Four laboratories employed ID calibration, the remaining used SA or EC. A total of seven independent results were submitted. Results for methionine were reported by only three laboratories, all of which used various acid digestion protocols combined with determination by GC-MS and LC UV. The majority of participants submitted values within the certified range for SeMet and total Se, whereas the intercomparison was judged unsuccessful for Met because only two external laboratories provided values, both of which were outside the certified range.

Effect of metal ions on the molecular weight distribution of humic substances derived from municipal compost: ultrafiltration and size exclusion chromatography with spectrophotometric and inductively coupled plasma-MS detection.

The effect of metal ions (Co, Cu, Ni, Pb, Zn) on the molecular weight distribution of humic substances (HSs) obtained from compost is studied. We believe this is the first of this type of study applied in this way to humic substances. Size exclusion chromatography is coupled with two on-line detection systems (spectrophotometric and ICPMS) to study the binding of metal ions by humic substances leached from compost. ICPMS provided highly specific, sensitive, and multielement analytical information that enabled obtaining direct experimental evidence for the participation of metal ions in molecular size distributions of humic compounds. The compost extract or its high molecular weight fraction (>5,000) was put in contact with EDTA or citrate ions, thereby competing with HSs for binding metals. The experiments were carried out by varying the pH maintained by Tris-HCl or CAPS buffer (pH 8.0 and 10.3) and keeping the ionic strength constant. The elution profile of humic substances using UV/ visible detection was compared with those from ICPMS detection of Co, Cu, Ni, Pb, and Zn in the same chromatographic runs. The results obtained suggested that both bridging between small molecules and complexation/ chelation by individual molecules are involved in metal ion binding to humic substances. The use of ICPMS to study the role of metal ions in aggregation/disassociation of humic substances proposed in this work is promising. Coupling element-specific detection with SEC or other separation systems allows better understanding of the mobility and bioaccessibility of elemental species in the environment and further elucidation of the dissolved humic structure.

SEC-ICP-MS studies for elements binding to different molecular weight fractions of humic substances in compost extract obtained from urban solid waste.

In this work, the speciation of elements in compost was studied with emphasis on their binding to humic substances. In order to assess the distribution of As, Cd, Co, Cr, Cu, Mn, Mo, Ni, Pb, U, Th and Zn among molecular weight fractions of humic substances, the compost extract (extracted by 0.1 mol l(-1) sodium pyrophosphate) was analyzed by size exclusion chromatography coupled on-line with UV-Vis spectrophotometric and ICP-MS detection. Similar chromatograms were obtained for standard humic acid (Fluka) and for compost extract (254 nm, 400 nm) and three size fractions were operationally defined that corresponded to the apparent molecular weight ranges > 15 kDa, 1-15 kDa and < 1 kDa. The percentage of total element content in compost that was leached to the extract ranged from 30% up to 100% for different elements. The elution profiles of Co, Cr, Cu, Ni and Pb (ICP-MS) followed that of humic substances, while for other elements the bulk elution peak matched the retention time observed for the element in the absence of compost extract. Spiking experiments were carried out to confirm elements' binding and to estimate the affinity of individual elements for humic substances derived from compost. The results obtained indicated the following order of decreasing affinity: Cu > Ni > Co > Pb > Cd > (Cr, U, Th) >> (As, Mn, Mo, Zn). After standard addition, further binding of Cu, Ni and Co with the two molecular weight fractions of humic substances was observed, indicating that humic substances derived from compost were not saturated with these elements.

Trace humic and fulvic acid determination in natural water by cloud point extraction/preconcentration using non-ionic and cationic surfactants with FI-UV detection.

A preconcentration and determination method for humic and fulvic acids at trace levels in natural water samples was developed. Cloud point extraction was successfully employed for the preconcentration of humic acid (HA) and fulvic acid (FA) prior to the determination by using a flow injection (FI) system coupled to a spectrophotometric UV-Vis detector. The quantitative extraction of HA and FA within the pH range 1-12 was obtained by neutralization of the anionic charge on the humic substances with a cationic surfactant, hexadecyltrimethylammonium bromide (CTAB). This generated a hydrophobic species that was subsequently incorporated (solubilized) into the micelles of a non-ionic surfactant polyethylene glycol, tert-octylphenyl ether (Triton X-114). The FI method for HA and FA determination was developed by injection of 100 microl of the extracted surfactant-rich phase using an HPLC pump with spectrophotometric detection at 350 nm. A 50 ml sample solution preconcentration allowed an enrichment factor of 167. The limit of detection (LOD) obtained under the optimal conditions was 5 microg l(-1). The precision for ten replicate determinations at 0.2 mg l(-1) HA was 3.1% relative standard deviation (RSD), calculated from the peak heights. The calibration using the preconcentration system for HA and FA was linear with a correlation coefficient (r2) of 0.9997 at levels near the detection limits up to at least 1 mg l(-1). The method was successfully applied to the determination of HA and FA in natural water samples (river water).