The development and implementation of quality assurance programs to support nutritional measurements.

The National Institute of Standards and Technology administers quality assurance programs devoted to improving measurements of nutrients and related metabolites in foods, dietary supplements, and serum and plasma samples. These programs have been developed in collaboration with the National Institutes of Health to assist measurement communities in their efforts to achieve accurate results that are comparable among different laboratories and over time. Targeted analytes include micronutrients, botanical markers, nutritional elements, contaminants, fatty acids, and vitamin D metabolites.

Evaluation of the state-of-the-art measurement capabilities for selected PBDEs and decaBB in plastic by the international intercomparison CCQM-P114.

An international intercomparison involving eight national metrology institutes (NMIs) was conducted to establish their current measurement capabilities for determining five selected congeners from the brominated flame retardant classes polybrominated diphenyl ethers and polybrominated biphenyls. A candidate reference material consisting of polypropylene fortified with technical mixtures of penta-, octa- and decabromo diphenyl ether and decabromo biphenyl, which was thoroughly assessed for material homogeneity and stability, was used as study material. The analytical procedures applied by the participants differed with regard to sample pre-treatment, extraction, clean-up, employed calibrants and type of calibration procedure as well as regarding analytical methods used for separation, identification and quantification of the flame retardant congeners (gas chromatography coupled to an electron capture detector (GC-ECD), gas chromatography-mass spectrometry in the electron ionisation mode (GC-EI-MS), gas chromatography-mass spectrometry in the electron capture negative ionisation mode (GC-ECNI-MS), and liquid chromatography-inductive coupled plasma-mass spectrometry (LC-ICP-MS)). The laboratory means agreed well with relative standard deviations of the mean of means of 1.9%, 4.8%, 5.5% and 5.4% for brominated diphenyl ether (BDE) 47, 183 and 209 and for the brominated biphenyl (BB) congener 209, respectively. For BDE 206, a relative standard deviation of 28.5% was obtained. For all five congeners, within-laboratory relative standard deviations of six measurements obtained under intermediate precision conditions were between 1% and 10%, and reported expanded measurements uncertainties typically ranged from 4% to 10% (8% to 14% for BDE 206). Furthermore, the results are in good agreement with those obtained in the characterization exercise for determining certified values for the flame retardant congeners in the same material. The results demonstrate the state-of-the-art measurement capabilities of NMIs for quantifying representative BDE congeners and BB 209 in a polymer. The outcome of this intercomparison (pilot study) in conjunction with possible improvements for employing exclusively calibrants with thoroughly assessed purity suggests that a key comparison aiming at underpinning calibration and measurement capability (CMC) claims of NMIs can be conducted.

Certification of standard reference materials containing bitter orange.

A suite of three dietary supplement standard reference materials (SRMs) containing bitter orange has been developed, and the levels of five alkaloids and caffeine have been measured by multiple analytical methods. Synephrine, octopamine, tyramine, N-methyltyramine, hordenine, total alkaloids, and caffeine were determined by as many as six analytical methods, with measurements performed at the National Institute of Standards and Technology and at two collaborating laboratories. The methods offer substantial independence, with two types of extractions, two separation methods, and four detection methods. Excellent agreement was obtained among the measurements, with data reproducibility for most methods and analytes better than 5% relative standard deviation. The bitter-orange-containing dietary supplement SRMs are intended primarily for use as measurement controls and for use in the development and validation of analytical methods.

Determination of HBCD, PBDEs and MeO-BDEs in California sea lions (Zalophus californianus) stranded between 1993 and 2003.

Blubber samples from male California sea lions (Zalphophus californianus) stranded between 1993 and 2003 were analyzed for 27 polybrominated diphenyl ether (PBDE) congeners, three isomers of hexabromocyclododecane (HBCD) and 14 methoxylated polybrominated diphenyl ether (MeO-BDE) congeners. Total PBDEs ranged from 450 ng/g to 4740 ng/g wet mass and total HBCD ranged from < 0.3 ng/g to 12 ng/g wet mass. The concentration of HBCD increased from 0.7 ng/g to12.0 ng/g wet mass in sea lion blubber between 1993 and 2003. However, no significant temporal trend was observed for any of the other brominated compounds over this 10 year period. Only one of the 14 MeO-BDE congeners was detected in the blubber samples, 6-methoxy-2,2',4,4'-tetrabromodiphenyl ether (6-MeO-BDE 47), and concentrations ranged from < 0.2 ng/g to 12 ng/g wet mass. A bromo-, chloro-heterocyclic compound, 1,1'-dimethyl-tetrabromo-dichloro-2,2'-bipyrrole (DBP-Br4Cl2), previously reported in marine species along the Pacific coast, was also identified in the sea lion blubber. DBP-Br4Cl2 ranged from 44 ng/g wet mass to 660 ng/g wet mass and was present at concentrations rivaling the dominant PBDE congener, BDE 47 (2,2',4,4'-tetrabromodiphenyl ether). Concentrations of DBP-Br4Cl2 were positively correlated with 6-MeO-BDE 47 (r = 0.7; p < 0.05). Both of these compounds have been identified in marine algae and sponges, and studies suggest they are both produced from natural sources. This study demonstrates that brominated compounds from both anthropogenic and biogenic sources can accumulate to similar levels in marine mammals. In addition, HBCD concentrations appear to be increasing in California sea lion populations, whereas PBDE concentrations, between 1993 and 2003, were highly variable.

Comparison of supercritical fluid extraction and Soxhlet extraction for the determination of polychlorinated biphenyls in environmental matrix standard reference materials.

Supercritical fluid extraction (SFE) was compared to traditional Soxhlet extraction for the determination of polychlorinated biphenyl congeners in three standard reference materials: SRM 1941a (Organics in Marine Sediment), SRM 1944 (New York/New Jersey Waterway Sediment) and SRM 2974 [Organics in Mussel Tissue (Mytilus edulis) (Freeze-Dried)]. The concentrations determined using SFE compared well with the certified concentrations for the majority of the polychlorinated biphenyl congeners.

Determination of PCBs and chlorinated hydrocarbons in marine mammal tissues.

Selected tissues (blubber, liver, kidney and muscle) from marine mammals, which were collected as part of the Alaska Marine Mammal Tissue Archival Project (AMMTAP), were analyzed for polychlorinated biphenyl (PCB) congeners and chlorinated pesticides. Concentrations of these compounds in the different tissues were compared and blubber was selected as the primary tissue for organic contaminant analyses for the AMMTAP based on higher levels (1-2 orders of magnitude) in this tissue compared to liver, kidney and muscle. Concentrations for 15 PCB congeners and 12 chlorinated pesticides are reported for 10 different animals of three species (northern fur seal, ringed seal and belukha whale) from five different sites.

Concentrations of chlorinated hydrocarbons and trace elements in marine mammal tissues archived in the U.S. National Biomonitoring Specimen Bank.

The U.S. National Biomonitoring Specimen Bank (NBSB) provides for the long term storage of well documented and preserved specimens representing several types of environmental matrices. A major part of this inventory consists of marine mammal tissues (e.g., blubber, liver, kidney, and muscle). Within the NBSB selected specimens are periodically analyzed for chlorinated hydrocarbons and trace elements. Although only 20% of the 560 marine mammal specimens in the NBSB have been analyzed, the database is of value in evaluating the stability of analytes and sample degradation during storage, for comparing with results from samples collected in the future for long-term monitoring, and for comparing with analytical results from other laboratories on samples collected at the same time for monitoring purposes. The NBSB analytical database contains results for 37 elements, many of which are not analyzed routinely by conventional analytical techniques used in monitoring programs, and the following organic compounds: selected PCB congeners. DDT compounds, alpha- and gamma-HCH, HCB, heptachlor epoxide, oxychlordane, cis-chlordane, trans-chlordane, cis-nonachlor, trans-nonachlor, and dieldrin in 9 marine mammal species: northern fur seal (Callorhinus ursinus), ringed seal (Phoca hispida), spotted seal (P. largha), bearded seal (Erignathus barbatus), pilot whale (Globicephala melas), harbor porpoise (Phocoena phocoena), white-sided dolphin (Lagenorhynchus acutus), beluga whale (Delphinapterus leucas), and bowhead whale (Balaena mysticetus). Analyses of beluga whale blubber for toxaphene and additional chlorinated hydrocarbons are obtained through collaboration with the Department of Fisheries and Oceans Canada.

Interlaboratory comparison study for PCB congeners and chlorinated pesticides in beluga whale blubber.

Three laboratories participated in an interlaboratory comparison exercise for the determination of polychlorinated biphenyl (PCB) congeners and chlorinated pesticides in Standard Reference Material (SRM) 1588 (Organics in Cod Liver Oil) a whale blubber control material, and six beluga whale (Delphinapterus leucas) blubber samples. The results are generally in good agreement. The minor disagreement of some of the results may be attributed to differences in detector calibrations, differences in chromatographic separation selectivity for specific compounds, or both. The SRM and control material help to validate the analytical procedures and to verify that these procedures remain in control.

Determination of non-ortho polychlorinated biphenyls in environmental Standard Reference Materials.

The concentrations of three non-ortho ("coplanar") polychlorinated biphenyls, 3,3',4,4'-tetrachlorobiphenyl (IUPAC PCB 77), 3,3',4,4',5-pentachlorobiphenyl (IUPAC PCB 126), and 3,3',4,4',5,5'-hexachlorobiphenyl (IUPAC PCB 169), were determined in five NIST Standard Reference Materials (SRMs) of environmental and biological interest. The measured levels were approximately between (0.2 to 1.3) ng/g in SRM 1588a (Organics in Cod Liver Oil), (0.3 to 9) ng/g in SRM 1944 (New York/New Jersey Waterway Sediment), (0.2 to 0.4) ng/g in SRM 1945 (Organics in Whale Blubber), (1 to 18) ng/g in SRM 2974 (Organics in Freeze-dried Mussel Tissue [Mytilus edulis]), and (0.1 to 0.4) ng/g in candidate SRM 1946 (Lake Superior Fish Tissue). PCB 169 was present at < 0.1 ng/g in SRMs 1944 and 2974.

Development, validation, and application of a method for quantification of methylmercury in biological marine materials using gas chromatography atomic emission detection.

A gas chromatographic method was developed for the quantification of alkylmercury species using microwave-induced plasma atomic emission detection (GC-AED). The column conditioning and analyte derivatization required for previous methods were found to be unnecessary for stable, accurate, and sensitive element-specific detection using GC-AED. Chromatographic and detection parameters such as stationary phase type, stationary phase film thickness, GC column dimensions, helium mobile phase column head pressure, detector makeup gas flow rate, and detector reagent gas type and flow rate were found to significantly affect analyte response. The detection limit for the optimized GC-AED conditions was 0.8 pg (0.1 pg/s) of methylmercury chloride (as mercury). A solid-liquid extraction procedure with preparative gel permeation chromatography cleanup and GC-AED analysis was used to quantify methylmercury in a variety of complex matrix marine materials. The methylmercury quantification method was validated with four marine certified reference materials (CRMs). The method was then applied to 13 standard reference materials, CRMs, and control materials for which no certified reference values for methylmercury have been determined. Four National Institute of Standards and Technology Standard Reference Materials and one control material, which were analyzed using the GC-AED method, were also analyzed by two other laboratories using independent methods to further validate the method.

Certification of polychlorinated biphenyl congeners and chlorinated pesticides in a whale blubber standard Reference Material.

A Standard Reference Material (SRM) made from whale blubber has been developed for the validation of methods used for the determination of polychlorinated biphenyl (PCB) congeners and chlorinated pesticides. This material, which is a frozen blubber tissue homogenate, was analyzed using three different analytical techniques. These techniques were based on gas chromatography with electron capture detection on two stationary phases with different selectivity for the separation of PCB congeners and gas chromatography with mass spectrometric detection. The results from these three techniques were in good agreement and were combined to provide certified concentrations for 27 PCB congeners and 15 chlorinated pesticides.

Determination of polychlorinated dibenzo-p-dioxin and dibenzofuran congeners in air particulate and marine sediment standard reference materials (SRMs).

Due to the limited number of environmental matrix certified reference materials (CRMs) with assigned values for natural levels of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs), an interlaboratory study was undertaken by the National Institute of Standards and Technology (NIST) and Environment Canada to establish reference concentration values for selected PCDD/Fs in two well-characterized NIST Standard Reference Materials (SRMs): SRM 1649a (Urban Dust) and SRM 1944 (New York/New Jersey Waterway Sediment). Results from 14 laboratories were used to provide reference values for the seventeen 2, 3, 7, 8-substituted PCDD/F congeners, the totals for individual tetra- through hepta-substituted PCDD/F homologues, and the total amount of tetra- through hepta-substituted PCDD/Fs. The mass fractions for the individual 2, 3, 7, 8-substituted congeners range from approximately 0.01 microg/kg to 7 microg/kg dry mass.

Certification of the methylmercury content in SRM 2977 mussel tissue (organic contaminants and trace elements) and SRM 1566b oyster tissue.

The methylmercury content in two new marine bivalve mollusk tissue Standard Reference Materials (SRMs) has been certified using results of analyses from the National Institute of Standards and Technology (NIST) and two other laboratories. The certified concentrations of methylmercury were established based on the results from four and six different (independent) analytical methods, respectively, for SRM 1566b Oyster Tissue (13.2 +/- 0.7 microg/kg) and SRM 2977 Mussel Tissue (organic contaminants and trace elements) (36.2 +/- 1.7 microg/kg). The certified concentration of methylmercury in SRM 1566b is among the lowest in any certified reference material (CRM).

Recent developments in food-matrix Reference Materials at NIST.

Since 1996, the National Institute of Standards and Technology (NIST) has developed several food-matrix Standard Reference Materials (SRMs) characterized for nutrient concentrations. These include SRM 1544 Fatty Acids and Cholesterol in a Frozen Diet Composite, SRM 1546 Meat Homogenate, SRM 1548a Typical Diet, SRM 1566b Oyster Tissue, SRM 1846 Infant Formula, and SRM 2383 Baby Food Composite. Three additional materials--SRM 1946 Lake Superior Fish Tissue, SRM 2384 Baking Chocolate, and SRM 2385 Spinach--are in preparation. NIST also recently assigned values for proximate (fat, protein, etc.), individual fatty acid, and total dietary fiber concentrations in a number of existing SRMs and reference materials (RMs) that previously had values assigned for their elemental composition. NIST has used several modes for assignment of analyte concentrations in the food-matrix RMs, including the use of data provided by collaborating laboratories, alone and in combination with NIST data. The use of data provided by collaborating food industry and contract laboratories for the analysis of food-matrix RMs has enabled NIST to provide assigned values for many analytes that NIST does not have the resources or analytical expertise to measure.