Human bone material characterization: integrated imaging surface investigation of male fragility fractures.

UNLABELLED: The interrelation of calcium and phosphorus was evaluated as a function of bone material quality in femoral heads from male fragility fracture patients via surface analytical imaging as well as scanning microscopy techniques. A link between fragility fractures and increased calcium to phosphorus ratio was observed despite normal mineralization density distribution. INTRODUCTION: Bone fragility in men has been recently recognized as a public health issue, but little attention has been devoted to bone material quality and the possible efficacy in fracture risk prevention. Clinical routine fracture risk estimations do not consider the quality of the mineralized matrix and the critical role played by the different chemical components that are present. This study uses a combination of different imaging and analytical techniques to gain insights into both the spatial distribution and the relationship of phosphorus and calcium in bone. METHODS: X-ray photoelectron spectroscopy and time-of-flight secondary ion mass spectrometry imaging techniques were used to investigate the relationship between calcium and phosphorus in un-embedded human femoral head specimens from fragility fracture patients and non-fracture age-matched controls. The inclusion of the bone mineral density distribution via backscattered scanning electron microscopy provides information about the mineralization status between the groups. RESULTS: A link between fragility fracture and increased calcium and decreased phosphorus in the femoral head was observed despite normal mineralization density distribution. Results exhibited significantly increased calcium to phosphorus ratio in the fragility fracture group, whereas the non-fracture control group ratio was in agreement with the literature value of 1.66 M ratio in mature bone. CONCLUSIONS: Our results highlight the potential importance of the relationship between calcium and phosphorus, especially in areas of new bone formation, when estimating fracture risk of the femoral head. The determination of calcium and phosphorus fractions in bone mineral density measurements may hold the key to better fracture risk assessment as well as more targeted therapies.

The influence of promoter and of electrode material on the cyclic voltammetry of Pisum sativum plastocyanin.

The reversible cyclic voltammetry of pea plastocyanin (Pisum sativum) was studied with a wide range of electrodes: edge-oriented pyrolytic graphite (PGE), glassy carbon (GCE), gold (Au) and platinum (Pt) electrodes. Plastocyanin was coated onto the electrode surface by exploiting the electrostatic interaction between the negatively charged protein and a wide range of positively charged promoters. The effect of the redox response with an extended range of promoters, including poly-L-lysine, polymyxin B, neomycin, tobramycin, geneticin, spermine and spermidine, were included in this study. The resulting cyclic voltammograms reveal that the observed midpoint potential for plastocyanin can be shifted significantly depending on the choice of promoter. The stability of the negatively charged plastocyanin-promoter layer on an electrode was gauged by the rate of bulk diffusion of the protein from the immobilised film into the solution. Reversible cyclic voltammograms were obtained using edge-oriented pyrolytic graphite (PGE) and glassy carbon electrodes (GCE) with all promoters; however, platinum and gold electrodes were unable to sustain a defined redox response. The combination of pyrolytic graphite electrode/poly-L-lysine/plastocyanin was found to be the most stable combination, with a redox response which remained well defined in solution for more than 1 h at pH 7.0. The midpoint potentials obtained in this manner differed between the two graphite electrodes PGE and GCE using poly-L-lysine as the promoter. This effect was in addition to the expected pH dependence of the midpoint potential for plastocyanin and the results indicated that the pK(a) for plastocyanin on PGE was 4.94 compared to that on GCE of 4.66. It is concluded that both the electrode material and the nature of the promoter can influence the position of the redox potentials for proteins measured in vitro. This study extends the range of biogenic promoters used in combination with electrode materials. Thus, we can begin to develop a more comprehensive understanding of electrode-protein interactions and draw conclusions as to metalloprotein function, in vivo. To support these studies, we have sought information as to the nature of the electrode/promoter/protein interaction using scanning tunneling microscopy (STM) to study both the promoter and the plastocyanin protein on a gold surface.

Parameters important in fabricating enzyme electrodes using self-assembled monolayers of alkanethiols.

The fabrication of enzyme electrodes using self-assembled monolayers (SAMs) has attracted considerable interest because of the spatial control over the enzyme immobilization. A model system of glucose oxidase covalently bound to a gold electrode modified with a SAM of 3-mercaptopropionic acid was investigated with regard to the effect of fabrication variables such as the surface topography of the underlying gold electrode, the conditions during covalent attachment of the enzyme and the buffer used. The resultant monolayer enzyme electrodes have excellent sensitivity and dynamic range which can easily be adjusted by controlling the amount of enzyme immobilized. The major drawback of such electrodes is the response which is limited by the kinetics of the enzyme rather than mass transport of substrates. Approaches to bringing such enzyme electrodes into the mass transport limiting regime by exploiting direct electron transfer between the enzyme and the electrode are outlined.

Scanning tunnelling microscopy imaging of [3 x 3] Mn nonanuclear grids.

The scanning tunnelling microscopy imaging of [3 x 3] Mn(II) nonanuclear grids on gold substrates is described. Self-assembled behaviour is observed at both high and low coverage, with submolecular resolution of individual molecules displayed at low deposition concentrations. The importance of proper image processing techniques is demonstrated in resolving the layer structure at high coverage.