RESUMEN
Our understanding of the dielectric response of interfacial water, which underlies the solvation properties and reaction rates at aqueous interfaces, relies on the linear response approximation: an external electric field induces a linearly proportional polarization. This implies antisymmetry with respect to the sign of the field. Atomistic simulations have suggested, however, that the polarization of interfacial water may deviate considerably from the linear response. Here we present an experimental study addressing this issue. We measured vibrational sum-frequency generation spectra of heavy water (D2O) near a monolayer graphene electrode, to study its response to an external electric field under controlled electrochemical conditions. The spectra of the OD stretch show a pronounced asymmetry for positive versus negative electrode charge. At negative charge below 5 × 1012 electrons per square centimetre, a peak of the non-hydrogen-bonded OD groups pointing towards the graphene surface is observed at a frequency of 2,700 per centimetre. At neutral or positive electrode potentials, this 'free-OD' peak disappears abruptly, and the spectra display broad peaks of hydrogen-bonded OD species (at 2,300-2,650 per centimetre). Miller's rule1 connects the vibrational sum-frequency generation response to the dielectric constant. The observed deviation from the linear response for electric fields of about ±3 × 108 volts per metre calls into question the validity of treating interfacial water as a simple dielectric medium.
RESUMEN
In Arabidopsis thaliana, female gametophyte (FG) development is accompanied by the formation and expansion of the large vacuole in the FG; this is essential for FG expansion, nuclear polar localization, and cell fate determination. Arabidopsis VACUOLELESS GAMETOPHYTES (VLG) facilitates vesicular fusion to form large vacuole in the FG, but the regulation of VLG remains largely unknown. Here, we found that gain-of-function mutation of BRASSINOSTEROID INSENSITIVE2 (BIN2) (bin2-1) increases VLG abundance to induce the vacuole formation at stage FG1, and leads to abortion of FG. Loss-of-function mutation of BIN2 and its homologs (bin2-3 bil1 bil2) reduced VLG abundance and mimicked vlg/VLG phenotypes. Knocking down VLG in bin2-1 decreased the ratio of aberrant vacuole formation at stage FG1, whereas FG1-specific overexpression of VLG mimicked the bin2-1 phenotype. VLG partially rescued the bin2-3 bil1 bil2 phenotype, demonstrating that VLG acts downstream of BIN2. Mutation of VLG residues that are phosphorylated by BIN2 altered VLG stability and a phosphorylation mimic of VLG causes similar defects as did bin2-1. Therefore, BIN2 may function by interacting with and phosphorylating VLG in the FG to enhance its stability and abundance, thus facilitating vacuole formation. Our findings provide mechanistic insight into how the BIN2-VLG module regulates the spatiotemporal formation of the large vacuole in FG development.
Asunto(s)
Proteínas de Arabidopsis , Arabidopsis , Arabidopsis/fisiología , Proteínas de Arabidopsis/metabolismo , Brasinoesteroides/metabolismo , Regulación de la Expresión Génica de las Plantas/genética , Células Germinativas de las Plantas/metabolismo , Óvulo Vegetal/genética , Óvulo Vegetal/metabolismo , Fosforilación , Proteínas Quinasas/metabolismo , Transducción de Señal/genética , Vacuolas/metabolismoRESUMEN
Uncovering the function of phytopathogen effectors is crucial for understanding mechanisms of pathogen pathogenicity and for improving our ability to protect plants from diseases. An increasing number of effectors have been predicted in various plant pathogens. Functional characterization of these effectors has become a major focus in the study of plant-pathogen interactions. In this study, we designed a novel screening system that combines the TMV (tobacco mosaic virus)-GFP vector and Agrobacterium-mediated transient expression in the model plant Nicotiana benthamiana. This system enables the rapid identification of effectors that interfere with plant immunity. The biological function of these effectors can be easily evaluated by observing the GFP fluorescence signal using a UV lamp within just a few days. To evaluate the TMV-GFP system, we initially tested it with well-described virulence and avirulence type III effectors from the bacterial pathogen Ralstonia solanacearum. After proving the accuracy and efficiency of the TMV-GFP system, we successfully screened a novel virulence effector, RipS1, using this approach. Furthermore, using the TMV-GFP system, we reproduced consistent results with previously known cytoplasmic effectors from a diverse array of pathogens. Additionally, we demonstrated the effectiveness of the TMV-GFP system in identifying apoplastic effectors. The easy operation, time-saving nature, broad effectiveness, and low technical requirements of the TMV-GFP system make it a promising approach for high-throughput screening of effectors with immune interference activity from various pathogens.
Asunto(s)
Vectores Genéticos , Proteínas Fluorescentes Verdes , Ensayos Analíticos de Alto Rendimiento , Nicotiana , Enfermedades de las Plantas , Ralstonia solanacearum , Virus del Mosaico del Tabaco , Virus del Mosaico del Tabaco/fisiología , Virus del Mosaico del Tabaco/genética , Virus del Mosaico del Tabaco/patogenicidad , Nicotiana/microbiología , Nicotiana/genética , Nicotiana/virología , Proteínas Fluorescentes Verdes/genética , Proteínas Fluorescentes Verdes/metabolismo , Ralstonia solanacearum/patogenicidad , Ralstonia solanacearum/genética , Ralstonia solanacearum/fisiología , Ensayos Analíticos de Alto Rendimiento/métodos , Enfermedades de las Plantas/microbiología , Vectores Genéticos/genética , Virulencia , Agrobacterium/genética , Inmunidad de la Planta/genética , Interacciones Huésped-Patógeno/genéticaRESUMEN
Electrocatalysts with low Pt loading mass to achieve high current density (≥1 A cm-2) for hydrogen evolution reaction (HER) are still extremely challenging due to the limited intrinsic activity and weak stability of catalytic sites. The modulation of the electronic microenvironment of the support-Pt structure is crucial to enhance the intrinsic activity and stability of catalytic sites. Herein, an innovative titanium oxycarbide (TiVCO) solid solution with Ti vacancies (TiV) is proposed as support to anchor sub-nanoscale Pt atomic clusters (Pt ACs) and a stable "TiV-Pt ACs" structure is carefully designed. The electronic microenvironment of "TiV-Pt ACs" is indirectly optimized by an unsaturated C/O site near TiV. Thanks to this, novel "TiV-Pt ACs" structure (Pt@TiVCO) with low Pt loading mass (2.44 wt.%) exhibits excellent HER activity in acidic solution and the mass activity is more than ten times that of commercial 20% Pt/C at the overpotentials of 50 and 100 mV. Particularly, Pt@TiVCO shows amazing stability at high and fluctuating current density of 1-2 A cm-2 for 120 h. This work provides a novel and promising method to develop stable and low-loading Pt-based catalysts adapting to high current density.
RESUMEN
Textiles represent a fundamental material format that is extensively integrated into our everyday lives. The quest for more versatile and body-compatible wearable electronics has led to the rise of electronic textiles (e-textiles). By enhancing textiles with electronic functionalities, e-textiles define a new frontier of wearable platforms for human augmentation. To realize the transformational impact of wearable e-textiles, materials innovations can pave the way for effective user adoption and the creation of a sustainable circular economy. We propose a repair, recycle, replacement and reduction circular e-textile paradigm. We envisage a systematic design framework embodying material selection and biofabrication concepts that can unify environmental friendliness, market viability, supply-chain resilience and user experience quality. This framework establishes a set of actionable principles for the industrialization and commercialization of future sustainable e-textile products.
RESUMEN
Photoelectrochemical solar fuel generation at the semiconductor/liquid interface consists of multiple elementary steps, including charge separation, recombination, and catalytic reactions. While the overall incident light-to-current conversion efficiency (IPCE) can be readily measured, identifying the microscopic efficiency loss processes remains difficult. Here, we report simultaneous in situ transient photocurrent and transient reflectance spectroscopy (TRS) measurements of titanium dioxide-protected gallium phosphide photocathodes for water reduction in photoelectrochemical cells. Transient reflectance spectroscopy enables the direct probe of the separated charge carriers responsible for water reduction to follow their kinetics. Comparison with transient photocurrent measurement allows the direct probe of the initial charge separation quantum efficiency (ÏCS) and provides support for a transient photocurrent model that divides IPCE into the product of quantum efficiencies of light absorption (Ïabs), charge separation (ÏCS), and photoreduction (Ïred), i.e., IPCE = ÏabsÏCSÏred. Our study shows that there are two general key loss pathways: recombination within the bulk GaP that reduces ÏCS and interfacial recombination at the junction that decreases Ïred. Although both loss pathways can be reduced at a more negative applied bias, for GaP/TiO2, the initial charge separation loss is the key efficiency limiting factor. Our combined transient reflectance and photocurrent study provides a time-resolved view of microscopic steps involved in the overall light-to-current conversion process and provides detailed insights into the main loss pathways of the photoelectrochemical system.
RESUMEN
To overcome pathogen infection, plants deploy a highly efficient innate immune system, which often uses hydrogen peroxide (H2O2), a versatile reactive oxygen species, to activate downstream defense responses. H2O2 is a potential substrate of aquaporins (AQPs), the membrane channels that facilitate the transport of small compounds across plasma membranes or organelle membranes. To date, however, the functional relationship between AQPs and H2O2 in plant immunity is largely undissected. Here, we report that the rice (Oryza sativa) AQP OsPIP2;2 transports pathogen-induced apoplastic H2O2 into the cytoplasm to intensify rice resistance against various pathogens. OsPIP2;2-transported H2O2 is required for microbial molecular pattern flg22 to activate the MAPK cascade and to induce the downstream defense responses. In response to flg22, OsPIP2;2 is phosphorylated at the serine residue S125, and therefore gains the ability to transport H2O2. Phosphorylated OsPIP2;2 also triggers the translocation of OsmaMYB, a membrane-anchored MYB transcription factor, into the plant cell nucleus to impart flg22-induced defense responses against pathogen infection. On the contrary, if OsPIP2;2 is not phosphorylated, OsmaMYB remains associated with the plasma membrane, and plant defense responses are no longer induced. These results suggest that OsPIP2;2 positively regulates plant innate immunity by mediating H2O2 transport into the plant cell and mediating the translocation of OsmaMYB from plasma membrane to nucleus.
Asunto(s)
Acuaporinas , Oryza , Acuaporinas/genética , Acuaporinas/metabolismo , Regulación de la Expresión Génica de las Plantas , Peróxido de Hidrógeno/metabolismo , Oryza/metabolismo , Proteínas de Plantas/genética , Proteínas de Plantas/metabolismo , Factores de Transcripción/genética , Factores de Transcripción/metabolismoRESUMEN
The highly variable and species-specific pollen surface patterns are formed by sporopollenin accumulation. The template for sporopollenin deposition and polymerization is the primexine that appears on the tetrad surface, but the mechanism(s) by which primexine guides exine patterning remain elusive. Here, we report that the Poaceae-specific EXINE PATTERN DESIGNER 1 (EPAD1), which encodes a nonspecific lipid transfer protein, is required for primexine integrity and pollen exine patterning in rice (Oryza sativa). Disruption of EPAD1 leads to abnormal exine pattern and complete male sterility, although sporopollenin biosynthesis is unaffected. EPAD1 is specifically expressed in male meiocytes, indicating that reproductive cells exert genetic control over exine patterning. EPAD1 possesses an N-terminal signal peptide and three redundant glycosylphosphatidylinositol (GPI)-anchor sites at its C terminus, segments required for its function and localization to the microspore plasma membrane. In vitro assays indicate that EPAD1 can bind phospholipids. We propose that plasma membrane lipids bound by EPAD1 may be involved in recruiting and arranging regulatory proteins in the primexine to drive correct exine deposition. Our results demonstrate that EPAD1 is a meiocyte-derived determinant that controls primexine patterning in rice, and its orthologs may play a conserved role in the formation of grass-specific exine pattern elements.
Asunto(s)
Antígenos de Plantas/metabolismo , Biopolímeros/metabolismo , Carotenoides/metabolismo , Proteínas Portadoras/metabolismo , Oryza/genética , Proteínas de Plantas/metabolismo , Antígenos de Plantas/genética , Proteínas Portadoras/genética , Flores/genética , Flores/metabolismo , Flores/ultraestructura , Mutación , Oryza/metabolismo , Oryza/ultraestructura , Proteínas de Plantas/genética , Poaceae , Polen/genética , Polen/metabolismo , Polen/ultraestructura , Especificidad de la EspecieRESUMEN
The Second Revision of the International Staging System (R2-ISS) was recently introduced to improve risk stratification over that provided by the extensively applied standard revised International Staging System (R-ISS). In addition to the variables included in the R-ISS, the R2-ISS incorporates chromosome 1q gain/amplification and divides the patients into 4 groups with different survival outcomes, better stratifying patients within the R-ISS intermediate-risk. The new model was developed based on a great quantity of data from patients participating in uniform clinical trials and has not been validated in real-world clinical practice. Therefore, we retrospectively analyzed the prognostic value of the R2-ISS in 474 consecutive patients with multiple myeloma receiving immunomodulatory drugs or proteasome inhibitor-based regimens as their first-line treatment. According to the R2-ISS, 41 (8.6%), 76 (16%), 275 (58%), and 82 (17.3%) patients were identified as R2-ISS I, R2-ISS II, R2-ISS III, and R2-ISS IV, respectively. The median progression-free survival (PFS) was 48 (95% CI: 38-58), 35 (95% CI: 23-47), 24 (95% CI: 21-27), and 12 (95% CI: 7-17) months, and the estimated median overall survival (OS) was 110 (95% CI: 42-178), 88 (95% CI: 75-101), 50 (95% CI: 43-57), and 26 (95% CI: 19-33) months (p < 0.001) in the 4 groups, respectively. The R2-ISS could also classify groups with distinct survival among patients with renal impairment or classified as R-ISS II. Adjusted by age, sex, treatment approaches and transplantation status, the R2-ISS was an independent prognostic factor associated with OS with a hazard ratio of 7.055 (95% CI: 3.626-13.726) (p < 0.001) for R2-ISS IV versus R2-ISS I and 2.707 (95% CI: 1.436-5.103) (p = 0.002) for R2-ISS III versus R2-ISS I. In conclusion, our results suggest that the R2-ISS is a simple and robust risk stratification tool for patients with multiple myeloma treated with novel drugs and could be used in everyday clinical practice.
Asunto(s)
Mieloma Múltiple , Humanos , Mieloma Múltiple/patología , Inhibidores de Proteasoma/uso terapéutico , Agentes Inmunomoduladores , Estadificación de Neoplasias , Estudios Retrospectivos , PronósticoRESUMEN
We report spectroscopic measurements of the local pH and pKa at an electrode/electrolyte interface using surface enhanced Raman scattering (SERS) spectroscopy of 4-mercaptobenzoic acid (4-MBA). In acidic and basic solutions, the protonated and deprotonated carboxyl functional groups at the electrode surface exist in the solution as -COOH and -COO-, which have different Raman active vibrational features at around 1697 and 1414 cm-1, respectively. In pH neutral water, as the applied electrochemical potential is varied from negative to positive, the acidic form of the 4-MBA (i.e., -COOH) decreases in Raman intensity and the basic form (i.e., -COO-) increases in Raman intensity. The change in local ion concentration is due to the application of electrochemical potentials and the accumulation of ions near the electrode surface. Under various applied potentials, the ratio of 1697 and 1587 cm-1 (pH-independent) peak areas spans the range between 0.7 and 0, and the ratio of the 1414 and 1587 cm-1 peak areas ranges from 0 to 0.3. By fitting these data to a normalized sigmoid function, we obtain the percentage of surface protonation/deprotonation, which can be related to the pKa and pH of the system. Thus, we can measure the local pKa at the electrode surface using the surface enhanced Raman signal of the 4-MBA.
RESUMEN
OBJECTIVES: Recently, the Mayo Clinic introduced a new staging system (the Mayo Additive Staging System [MASS]) for patients with newly diagnosed multiple myeloma (NDMM) based on the number of high-risk (HR) abnormalities, including HR IgH translocations, 1q gain/amplification, chromosome 17 abnormalities, International Staging System (ISS)-III, and elevated lactate dehydrogenase. Patients with 0, 1, or ≥2 HR abnormalities were defined as stage I, II, or III, respectively. We aimed to validate the real-world prognostic value of the MASS. METHODS: We retrospectively analyzed the cytogenetic and laboratory results of 544 patients with NDMM at a single center. RESULTS: Ninety (16.5%) patients had no HR factors (MASS I), 193 (35.5%) had 1 HR factor (MASS II), and 261 (48%) had ≥2 HR factors (MASS III). The median progression-free survival (PFS) and overall survival (OS) times were 48, 28, and 20 months and 137, 73, and 39 months in the three groups, respectively (p < .001). In the subgroup analysis, patients had different OS outcomes based on the MASS when grouped by age, renal function, or therapeutic regimens. The MASS identified patients with the worst outcomes among those rated revised ISS II. CONCLUSION: The MASS system is a reliable risk stratification tool for patients with NDMM in real-world clinical practice.
Asunto(s)
Mieloma Múltiple , Humanos , Mieloma Múltiple/diagnóstico , Mieloma Múltiple/genética , Mieloma Múltiple/terapia , Estadificación de Neoplasias , Estudios Retrospectivos , Pronóstico , Aberraciones CromosómicasRESUMEN
Intelligent operation and maintenance technology for vessels can ensure the safety of the entire system, especially for the development of intelligent and unmanned marine technology. The material properties of metal abrasive particles in oil could demonstrate the wear areas of the marine mechanical system because different components consist of different materials. However, most sensors can only roughly separate metallic contaminants into ferromagnetic and non-ferromagnetic particles but cannot differentiate them in greater detail. A micro-three-coil sensor is designed in this paper; the device applies different excitation signals to two excitation coils to differentiate materials, based on the different effects of different material particles in the asymmetric magnetic field. Therefore, a particle's material can be judged by the shape of the induction electromotive force output signal from the induction coil, while the particle size can be judged by the amplitude of the signal. Experimental results show that the material differentiation of four different types of particles can be achieved, namely, of aluminum, iron, 304 stainless steel, and carbon steel. This newly designed sensor provides a new research prospect for the realization of an inductive detection method to distinguish non-ferrous metals and a reference for the subsequent detection of metal contaminants in oil and other liquids.
RESUMEN
Understanding the relaxation and injection dynamics of hot electrons is crucial to utilizing them in photocatalytic applications. While most studies have focused on hot carrier dynamics at metal/semiconductor interfaces, we study the in situ dynamics of direct hot electron injection from metal to adsorbates. Here, we report a hot electron-driven hydrogen evolution reaction (HER) by exciting the localized surface plasmon resonance (LSPR) in Au grating photoelectrodes. In situ ultrafast transient absorption (TA) measurements show a depletion peak resulting from hot electrons. When the sample is immersed in solution under -1 V applied potential, the extracted electron-phonon interaction time decreases from 0.94 to 0.67 ps because of additional energy dissipation channels. The LSPR TA signal is redshifted with delay time because of charge transfer and subsequent change in the dielectric constant of nearby solution. Plateau-like photocurrent peaks appear when exciting a 266 nm linewidth grating with p-polarized (on resonance) light, accompanied by a similar profile in the measured absorptance. Double peaks in the photocurrent measurement are observed when irradiating a 300 nm linewidth grating. The enhancement factor (i.e., reaction rate) is 15.6× between p-polarized and s-polarized light for the 300 nm linewidth grating and 4.4× for the 266 nm linewidth grating. Finite-difference time domain (FDTD) simulations show two resonant modes for both grating structures, corresponding to dipolar LSPR modes at the metal/fused silica and metal/water interfaces. To our knowledge, this is the first work in which LSPR-induced hot electron-driven photochemistry and in situ photoexcited carrier dynamics are studied on the same plasmon resonance structure with and without adsorbates.
RESUMEN
Reliable laser imaging is crucial to the autonomous driving. In unfavorable weather condition, however, it always suffers from the acute background noise and signal attenuation due to the harmful strong scattering. We demonstrate a noise-tolerant LiDAR with the help of Bessel beam illumination and single-photon detection. After a 31.5-m propagation in thick fog, the Bessel beam employed by our noise-tolerant LiDAR still owns a central spot with the diameter of 1.86 mm, which supports a receiving field of view as small as 60 µrad and a great suppression of the background noise. This noise-tolerant LiDAR simultaneously performs well both in depth and intensity imaging in unfavorable weather, which can be functioned as a reliable imaging sensor in automatic driving.
RESUMEN
A method for analyzing the influence of velocity changes on metal signals of different materials in oil detection technology is proposed. The flow rate of metal contaminants in the oil will have a certain impact on the sensitivity of the output particle signal in terms of electromagnetic fields and circuits. The detection velocity is not only related to the sensitivity of the output particle signal, but also to the adaptability of high-speed and high-throughput in oil online monitoring. In this paper, based on a high-sensitivity inductive bridge, the eddy current effect of velocity in a time-harmonic magnetic field is theoretically analyzed and experimentally verified, the phenomenon of particle signal variation with velocity for different materials is analyzed and discussed, and finally the effect of velocity on the output signal of the processing circuit is also elaborated and experimentally verified. Experiments show that under the influence of the time-harmonic magnetic field, the increase of the velocity enhances the detection sensitivity of non-ferromagnetic metal particles and weakens the detection sensitivity of non-ferromagnetic particles. Under the influence of the processing circuit, different velocities will produce different signal gains, which will affect the stability of the signal at different velocities.
RESUMEN
Nanoscale oxide layer protected semiconductor photoelectrodes show enhanced stability and performance for solar fuels generation, although the mechanism for the performance enhancement remains unclear due to a lack of understanding of the microscopic interfacial field and its effects. Here, we directly probe the interfacial fields at p-GaP electrodes protected by n-TiO2 and its effect on charge carriers by transient reflectance spectroscopy. Increasing the TiO2 layer thickness from 0 to 35 nm increases the field in the GaP depletion region, enhancing the rate and efficiency of interfacial electron transfer from the GaP to TiO2 on the ps time scale as well as retarding interfacial recombination on the microsecond time scale. This study demonstrates a general method for providing a microscopic view of the photogenerated charge carrier's pathway and loss mechanisms from the bulk of the electrode to the long-lived separated charge at the interface that ultimately drives the photoelectrochemical reactions.
Asunto(s)
Óxidos , Titanio , Electrodos , Luz SolarRESUMEN
We explore the effect of charge density wave (CDW) on the in-plane thermoelectric transport properties of (PbSe)1+δ(VSe2)1 and (PbSe)1+δ(VSe2)2 heterostructures. In (PbSe)1+δ(VSe2)1 we observe an abrupt 86% increase in the Seebeck coefficient, 245% increase in the power factor, and a slight decrease in resistivity over the CDW transition. This behavior is not observed in (PbSe)1+δ(VSe2)2 and is rather unusual compared to the general trend observed in other materials. The abrupt transition causes a deviation from the Mott relationship through correlated electron states. Raman spectra of the (PbSe)1+δ(VSe2)1 material show the emergence of additional peaks below the CDW transition temperature associated with VSe2 material. Temperature-dependent in-plane X-ray diffraction (XRD) spectra show a change in the in-plane thermal expansion of VSe2 in (PbSe)1+δ(VSe2)1 due to lattice distortion. The increase in the power factor and decrease in the resistivity due to CDW suggest a potential mechanism for enhancing the thermoelectric performance at the low temperature region.
RESUMEN
BACKGROUND: This study aimed to explore the heterogeneity of circRNA expression pattern via microarray, and further evaluate the potential of 10 specific circRNAs as diagnostic and prognostic biomarkers in multiple myeloma (MM). METHODS: In exploration stage (stage I), circRNA expression profiles were detected by the microarray in bone marrow plasma cells from 4 MM patients and 4 healthy controls (HCs), and bioinformatic analyses were performed. In validation stage (stage II), top 10 upregulated and top 10 downregulated circRNAs identified in stage I were detected in 60 MM patients and 30 HCs for further validation; the diagnostic and prognostic values of these circRNAs in MM patients were analyzed. RESULTS: In stage I, 122 upregulated and 260 downregulated circRNAs were identified in MM patients compared with HCs. GO, KEGG and pathway enrichment analyses revealed that these circRNAs were implicated in neoplastic pathways such as MAPK and VEGF signaling pathways. In stage II, circ-PTK2, circ-RNF217, circ-RERE, circ-NAGPA and circ-KCNQ5 were validated to be upregulated and circ-AFF2, circ-WWC3, circ-DNAJC5, circ-KLHL2, circ-IQGAP1 and circ-AL137655 were validated to be downregulated in MM compared with controls. Circ-PTK2 and circ-RNF217 were correlated with poor treatment response and survival, while circ-AFF2 predicted good treatment response and survival in MM patients. CONCLUSIONS: This study provides valuable reference for profound understanding about circRNA expression patterns in MM, and validates that circ-PTK2, circ-RNF217 and circ-AFF2 might serve as potential prognostic biomarkers in MM.
Asunto(s)
Biomarcadores de Tumor , Perfilación de la Expresión Génica , Mieloma Múltiple/diagnóstico , Mieloma Múltiple/genética , ARN Circular , Transcriptoma , Anciano , Biología Computacional/métodos , Femenino , Perfilación de la Expresión Génica/métodos , Ontología de Genes , Redes Reguladoras de Genes , Humanos , Biopsia Líquida/métodos , Masculino , Persona de Mediana Edad , Anotación de Secuencia Molecular , Mieloma Múltiple/mortalidad , Estadificación de Neoplasias , Pronóstico , Curva ROC , Reproducibilidad de los Resultados , Flujo de TrabajoRESUMEN
Plasmon resonant grating structures provide an effective platform for distinguishing between the effects of plasmon resonant excitation and bulk metal absorption via interband transitions. By simply rotating the polarization of the incident light, we can switch between resonant excitation and non-resonant excitation, while keeping all other parameters of the measurement constant. With light polarized perpendicular to the lines in the grating (i.e., TE-polarization), the photocatalytic reaction rate (i.e., photocurrent) is measured as the angle of the incident laser light is tuned through the resonance with the grating. Here, hot holes photoexcited in the metal are used to drive the oxygen evolution reaction (OER), producing a measurable photocurrent. Using TE-polarized light, we observe sharp peaks in the photocurrent and sharp dips in the photoreflectance at approximately 9° from normal incidence, which corresponds to the conditions under which there is good wavevector matching between the incident light and the lines in the grating. With light polarized parallel to the grating (i.e., TM), we excite the grating structure non-resonantly and there is no angular dependence in the photocurrent or photoreflectance. In order to quantify the lifetime of these hot carriers, we performed transient absorption spectroscopy of these plasmon resonant grating structures. Here, we observe one feature in the spectra corresponding to interband transitions and another feature associated with the plasmon resonant mode in the grating. Both features decay over a time scale of 1-2 ps. The spectral responses of grating structures fabricated with Ag, Al, and Cu are also presented.
RESUMEN
With age, our blood vessels are prone to aging, which induces cardiovascular disease. As an important basis for diagnosing heart disease and evaluating heart function, the electrocardiogram (ECG) records cardiac physiological electrical activity. Abnormalities in cardiac physiological activity are directly reflected in the ECG. Thus, ECG research is conducive to heart disease diagnosis. Considering the complexity of arrhythmia detection, we present an improved convolutional neural network (CNN) model for accurate classification. Compared with the traditional machine learning methods, CNN requires no additional feature extraction steps due to the automatic feature processing layers. In this paper, an improved CNN is proposed to automatically classify the heartbeat of arrhythmia. Firstly, all the heartbeats are divided from the original signals. After segmentation, the ECG heartbeats can be inputted into the first convolutional layers. In the proposed structure, kernels with different sizes are used in each convolution layer, which takes full advantage of the features in different scales. Then a max-pooling layer followed. The outputs of the last pooling layer are merged and as the input to fully-connected layers. Our experiment is in accordance with the AAMI inter-patient standard, which included normal beats (N), supraventricular ectopic beats (S), ventricular ectopic beats (V), fusion beats (F), and unknown beats (Q). For verification, the MIT arrhythmia database is introduced to confirm the accuracy of the proposed method, then, comparative experiments are conducted. The experiment demonstrates that our proposed method has high performance for arrhythmia detection, the accuracy is 99.06%. When properly trained, the proposed improved CNN model can be employed as a tool to automatically detect different kinds of arrhythmia from ECG.