Stretchable pumps for soft machines.

Machines made of soft materials bridge life sciences and engineering1. Advances in soft materials have led to skin-like sensors and muscle-like actuators for soft robots and wearable devices1-3. Flexible or stretchable counterparts of most key mechatronic components have been developed4,5, principally using fluidically driven systems6-8; other reported mechanisms include electrostatic9-12, stimuli-responsive gels13,14 and thermally responsive materials such as liquid metals15-17 and shape-memory polymers18. Despite the widespread use of fluidic actuation, there have been few soft counterparts of pumps or compressors, limiting the portability and autonomy of soft machines4,8. Here we describe a class of soft-matter bidirectional pumps based on charge-injection electrohydrodynamics19. These solid-state pumps are flexible, stretchable, modular, scalable, quiet and rapid. By integrating the pump into a glove, we demonstrate wearable active thermal management. Embedding the pump in an inflatable structure produces a self-contained fluidic 'muscle'. The stretchable pumps have potential uses in wearable laboratory-on-a-chip and microfluidic sensors, thermally active clothing and autonomous soft robots.

Silicone-layered waterproof electrohydraulic soft actuators for bio-inspired underwater robots.

Electrohydraulic soft actuators are a promising soft actuation technology for constructing bio-inspired underwater robots owing to the features of this technology such as large deformations and forces, fast responses, and high electromechanical efficiencies. However, this actuation technology requires high voltages, thereby limiting the use of these actuators in water and hindering the development of underwater robots. This paper describes a method for creating bio-inspired underwater robots using silicone-layered electrohydraulic soft actuators. The silicone layer functions as an insulator, enabling the application of high voltages underwater. Moreover, bending and linear actuation can be achieved by applying the silicone layers on one or both sides of the actuator. As a proof of concept, bending and linear actuators with planar dimensions of 20 mm × 40 mm (length × width) are fabricated and characterized. Underwater actuation is observed in both types of actuators. The bending actuators exhibit a bending angle and blocked force of 39.0° and 9.6 mN, respectively, at an applied voltage of 10 kV. Further, the linear actuators show a contraction strain and blocked force of 6.6% and 956.1 mN, respectively, at an applied voltage of 10 kV. These actuators are tested at a depth near the surface of water. This ensured that they can operate at least at that depth. The actuators are subsequently used to implement various soft robotic devices such as a ray robot, a fish robot, a water-surface sliding robot, and a gripper. All of the robots exhibit movements as expected; up to 31.2 mm/s (0.91 body length/s) of locomotion speed is achieved by the swimming robots and a retrieve and place task is performed by the gripper. The results obtained in this study indicate the successful implementation of the actuator concept and its high potential for constructing bio-inspired underwater robots and soft robotics applications.

Plant Robots: Harnessing Growth Actuation of Plants for Locomotion and Object Manipulation.

Plants display physical displacements during their growth due to photosynthesis, which converts light into chemical energy. This can be interpreted as plants acting as actuators with a built-in power source. This paper presents a method to create plant robots that move and perform tasks by harnessing the actuation output of plants: displacement and force generated from the growing process. As the target plant, radish sprouts are employed, and their displacement and force are characterized, followed by the calculation of power and energy densities. Based on the characterization, two different plant robots are designed and fabricated: a rotational robot and a gripper. The former demonstrates ground locomotion, achieving a travel distance of 14.6 mm with an average speed of 0.8 mm h-1. The latter demonstrates the picking and placing of an object with a 0.1-g mass by the light-controlled open-close motion of plant fingers. A good agreement between the experimental and model values is observed in the specific data of the mobile robot, suggesting that obtaining the actuation characteristics of plants can enable the design and prediction of behavior in plant robots. These results pave the way for the realization of novel types of environmentally friendly and sustainable robots.

Functional soft robotic composites based on organic photovoltaic and dielectric elastomer actuator.

Improving the energy efficiency of robots remains a crucial challenge in soft robotics, with energy harvesting emerging as a promising approach to address it. This study presents a functional soft robotic composite called OPV-DEA, which integrates flexible organic photovoltaic (OPV) and dielectric elastomer actuator (DEA). The composite can simultaneously generate electrostatic bending actuation and harvest energy from external lights. Owing to its simplicity and inherent flexibility, the OPV-DEA is poised to function as a fundamental building block for soft robots. This study aimed to validate this concept by initially establishing the fabrication process of OPV-DEA. Subsequently, experimental samples are fabricated and characterized. The results show that the samples exhibit a voltage-controllable bending actuation of up to 15.6° and harvested power output of 1.35 mW under an incident power irradiance of 11.7 mW/cm2. These performances remain consistent even after 1000 actuation cycles. Finally, to demonstrate the feasibility of soft robotic applications, an untethered swimming robot equipped with two OPV-DEAs is fabricated and tested. The robot demonstrates swimming at a speed of 21.7 mm/s. The power consumption of the robot is dominated by a high-voltage DC-DC converter, with a value approximately 1.5 W. As a result, the on-board OPVs cannot supply the necessary energy during locomotion simultaneously. Instead, they contribute to the overall system by charging a battery used for the controller on board. Nevertheless, these findings suggest that the OPV-DEA could pave the way for the development of an unprecedented range of functional soft robots.

Silicone-based highly stretchable multifunctional fiber pumps.

Recent advancements on electrohydrodynamic (EHD) soft pumps demonstrate their applicability to various fluid-driven systems such as soft robots, wearable devices, and stretchable electronics. In particular, fiber type EHD pumps reported more recently is a promising pumping element thanks to their versatile fibrous structure. Yet existing EHD fiber pumps are less stretchable and require sophisticated, complex fabrication equipment, implying opportunity for technology advancement. This paper presents a simplified method to create highly stretchable multifunctional fiber EHD pumps. The method employs highly compliant silicone elastomers for the fiber structure that is formed by simple dipping fabrication process. The fabricated pumps (length of 100 mm, inner diameter 4 mm, and mass 5.3 g) exhibit a high stretchability (up to 40% strain) and flow rate and pressure of 167.4 ± 7.6 mL/min (31.6 mL/min/g) and 4.1 ± 0.6 kPa (0.8 kPa/g), respectively. These performances are comparable or even higher than those of previously reported EHD pumps including fiber types. The output performance of the fabricated pumps remain constant for repeated strain cycles (0-25%, up to 2000 cycles) and bending angle up to 180° (corresponding to curvature of 0-30/m). Moreover, the pumps demonstrate unprecedented functionality as a sensor to distinguish the type of fluid inside the tube and to detect strains by reading the capacitance between the electrodes. The characterization result reveals the sensing ability of the pumps as high repeatability up to 30% strain with negligible hysteresis, which is consistent for 5000 cycles.

Fast-Response Variable-Stiffness Magnetic Catheters for Minimally Invasive Surgery.

In minimally invasive surgery, such as cardiac ablation, magnetically steered catheters made of variable-stiffness materials can enable higher dexterity and higher force application to human tissue. However, the long transition time between soft and rigid states leads to a significant increase in procedure duration. Here, a fast-response, multisegmented catheter is described for minimally invasive surgery made of variable-stiffness thread (FRVST) that encapsulates a helical cooling channel. The rapid stiffness change in the FRVST, composed of a nontoxic shape memory polymer, is achieved by an active cooling system that pumps water through the helical channel. The FRVST displays a 66 times stiffness change and a 26 times transition enhancement compare with the noncooled version. The catheter allows for selective bending of each segment up to 127° in air and up to 76° in water under an 80 mT external magnetic field. The inner working channel can be used for cooling an ablation tip during a procedure and for information exchange via the deployment of wires or surgical tools.

Soft-body dynamics induces energy efficiency in undulatory swimming: A deep learning study.

Recently, soft robotics has gained considerable attention as it promises numerous applications thanks to unique features originating from the physical compliance of the robots. Biomimetic underwater robots are a promising application in soft robotics and are expected to achieve efficient swimming comparable to the real aquatic life in nature. However, the energy efficiency of soft robots of this type has not gained much attention and has been fully investigated previously. This paper presents a comparative study to verify the effect of soft-body dynamics on energy efficiency in underwater locomotion by comparing the swimming of soft and rigid snake robots. These robots have the same motor capacity, mass, and body dimensions while maintaining the same actuation degrees of freedom. Different gait patterns are explored using a controller based on grid search and the deep reinforcement learning controller to cover the large solution space for the actuation space. The quantitative analysis of the energy consumption of these gaits indicates that the soft snake robot consumed less energy to reach the same velocity as the rigid snake robot. When the robots swim at the same average velocity of 0.024 m/s, the required power for the soft-body robot is reduced by 80.4% compared to the rigid counterpart. The present study is expected to contribute to promoting a new research direction to emphasize the energy efficiency advantage of soft-body dynamics in robot design.

Robot locomotion by fluid-fluid interaction.

This paper describes a locomotion strategy for robots based on the interaction between two fluids, through the development of an untethered mobile robot. The fundamental principle of robot locomotion is to exploit the active deformations of ferrofluid caused by internal magnetic fields, which generate reaction forces to the surrounding fluid (in this study, water). The developed robot is equipped with two permanent magnets (PMs), two electromagnets (EMs), two clusters of ferrofluid, and a control unit with batteries. It has a length, width, and mass of 107 mm, 94 mm, and 127 g, respectively. In the robot, PMs are used to hold clusters of ferrofluid. The activation of EMs by the controller achieves forward and rotational movements of the robot. Experimental results show the forward speed and rotational speed in water to be 2.7 mm/s (at a driving frequency of 9 Hz) and 1.2°/s (at a driving frequency of 7 Hz), respectively. The measured thrust force of the robot is 2 mN, further supporting the concept of robot locomotion by fluid-fluid interaction.

Polyvinyl chloride-added dibutyl adipate for high-performance electrohydrodynamic pumps.

Electrohydrodynamic (EHD) pumps are a promising driving source for various fluid-driven systems owing to features such as simple structure and silent operation. The performance of EHD pumps depends on the properties of the working fluid, such as conductivity, viscosity, and permittivity. This implies that the tuning of these parameters in a working fluid can enhance the EHD performance. This study reports a method to modify the properties of a liquid for EHD pumps by mixing an additive. Specifically, dibutyl adipate (DBA) and polyvinyl chloride (PVC) are employed as the working fluid and the additive, respectively. The results show that when the concentration of PVC is 0.2%, the flow rate and pressure at applied voltage of 8 kV take highest value of 7.85 µL/s and 1.63 kPa, respectively. These values correspond to an improvement of 109% and 40% for the flow rate and pressure, respectively, compared to the pure DBA (PVC 0%). When the voltage is 10 kV, the flow rate of 10.95 µL/s and the pressure of 2.07 kPa are observed for DBA with PVC concentration of 0.2%. These values are more than five times higher than those observed for FC40 at the same voltage (2.02 µL/s and 0.32 kPa). The results also suggest that optimal conductivity and viscosity values exist for maximizing the EHD performance of a liquid. This demonstrates the validity of the proposed method for realizing high-performance EHD pumps by using additives in the working fluid.

Rolled Dielectric Elastomer Antagonistic Actuators for Biomimetic Underwater Robots.

In this study, an antagonistic actuator using dielectric elastomer actuators (DEAs) is developed to investigate the use of rolled DEAs in underwater robots. The actuator consists of a backbone, an elastic hinge, and two rolled DEAs placed in an antagonistic fashion, allowing for the generation of bidirectional movements of the actuator tip. To prove this concept, an analytical model of the actuator is built. The experimental samples are fabricated based on the specification determined by the model. In the fabricated actuator, each rolled DEA has a diameter of 6 mm and a length of 21 mm. The whole device weighs 1.7 g. In the tested voltage range of 0-1200 V, the actuator exhibits a voltage-controllable angle and torque of up to 2.2° and 11.3 mN∙mm, respectively. The actuator is then implemented into a swimming robot, which shows forward speed of 0.9 mm/s at the applied voltage of 1000 V and the driving frequency of 10 Hz. The results demonstrate the feasibility of using rolled DEAs in underwater robots.

Peristaltic micropump using polyvinyl chloride gels with micropatterned surface.

This paper presents a pump using polyvinyl chloride (PVC) gel. PVC gels are compliant, have a simple structure, and exhibit large deformation at voltages in the range of 100-1000 V, which make them suitable for micropumps. In this study, a PVC gel sheet with a surface pattern that enhances active deformation in the thickness direction was employed for the fabrication of a pump. To this end, the PVC gel sheet was sandwiched between three sets of anode and cathode electrodes, after which voltages were sequentially applied to these electrodes to generate a peristaltic deformation of the gel sheet, thus pushing the liquid and creating a one-directional flow. Various pumps were fabricated using PVC gel sheets with different surface patterns, and the pumps were characterized. The pumps exhibited an outline dimension of 35 mm × 25 mm with a thickness of 4 mm, corresponding to a total volume of 3.5 × 103 mm3. The results revealed that the pump fabricated using a 174-µm-high pyramid-patterned gel sheet generated a flow rate of 224.1 µL/min at an applied voltage of 800 V and a driving frequency of 3 Hz. This observed value is comparable to or better than those of existing pumps based on smart materials.

Dielectric Elastomer Fiber Actuators with Aqueous Electrode.

Dielectric elastomer actuators (DEAs) are one of the promising actuation technologies for soft robotics. This study proposes a fiber-shaped DEA, namely dielectric elastomer fiber actuators (DEFAs). The actuator consisted of a silicone tube filled with the aqueous electrode (sodium chloride solution). Furthermore, it could generate linear and bending actuation in a water environment, which acts as the ground side electrode. Linear-type DEFA and bending-type DEFA were fabricated and characterized to prove the concept. A mixture of Ecoflex 00-30 (Smooth-On) and Sylgard 184 (Dow Corning) was employed in these actuators for the tube part, which was 75.0-mm long with outer and inner diameters of 6.0 mm and 5.0 mm, respectively. An analytical model was constructed to design and predict the behavior of the devices. In the experiments, the linear-type DEFA exhibited an actuation strain and force of 1.3% and 42.4 mN, respectively, at 10 kV (~20 V/µm) with a response time of 0.2 s. The bending-type DEFA exhibited an actuation angle of 8.1° at 10 kV (~20 V/µm). Subsequently, a jellyfish-type robot was developed and tested, which showed the swimming speed of 3.1 mm/s at 10 kV and the driving frequency of 4 Hz. The results obtained in this study show the successful implementation of the actuator concept and demonstrate its applicability for soft robotics.

Characterization of Sustainable Robotic Materials and Finite Element Analysis of Soft Actuators Under Biodegradation.

Biodegradability is an important property for soft robots that makes them environmentally friendly. Many biodegradable materials have natural origins, and creating robots using these materials ensures sustainability. Hence, researchers have fabricated biodegradable soft actuators of various materials. During microbial degradation, the mechanical properties of biodegradable materials change; these cause changes in the behaviors of the actuators depending on the progression of degradation, where the outputs do not always remain the same against identical inputs. Therefore, to achieve appropriate operation with biodegradable soft actuators and robots, it is necessary to reflect the changes in the material properties in their design and control. However, there is a lack of insight on how biodegradable actuators change their actuation characteristics and how to identify them. In this study, we build and validate a framework that clarifies changes in the mechanical properties of biodegradable materials; further, it allows prediction of the actuation characteristics of degraded soft actuators through simulations incorporating the properties of the materials as functions of the degradation rates. As a biodegradable material, we use a mixture of gelatin and glycerol, which is fabricated in the form of a pneumatic soft actuator. The experimental results show that the actuation performance of the physical actuator reduces with the progression of biodegradation. The experimental data and simulations are in good agreement (R 2 value up to 0.997), thus illustrating the applicability of our framework for designing and controlling biodegradable soft actuators and robots.

Cartilage structure increases swimming efficiency of underwater robots.

Underwater robots are useful for exploring valuable resources and marine life. Traditional underwater robots use screw propellers, which may be harmful to marine life. In contrast, robots that incorporate the swimming principles, morphologies, and softness of aquatic animals are expected to be more adaptable to the surrounding environment. Rajiform is one of the swimming forms observed in nature, which swims by generating the traveling waves on flat large pectoral fins. From an anatomical point of view, Rajiform fins consist of cartilage structures encapsulated in soft tissue, thereby realizing anisotropic stiffness. We hypothesized that such anisotropy is responsible for the generation of traveling waves that enable a highly efficient swimming. We validate our hypothesis through the development of a stingray robot made of silicone-based cartilages and soft tissue. For comparison, we fabricate a robot without cartilages, as well as the one combining soft tissue and cartilage materials. The fabricated robots are tested to clarify their stiffness and swimming performance. The results show that inclusion of cartilage structure in the robot fins increases the swimming efficiency. It is suggested that arrangement and distribution of soft and hard areas inside the body structure is a key factor to realize high-performance soft underwater robots.

Monolithic Stacked Dielectric Elastomer Actuators.

Dielectric elastomer actuators (DEAs) are a promising actuator technology for soft robotics. As a configuration of this technology, stacked DEAs afford a muscle-like contraction that is useful to build soft robotic systems. In stacked DEAs, dielectric and electrode layers are alternately stacked. Thus, often a dedicated setup with complicated processes or sometimes laborious manual stacking of the layers is required to fabricate stacked actuators. In this study, we propose a method to monolithically fabricate stacked DEAs without alternately stacking the dielectric and electrode layers. In this method, the actuators are fabricated mainly through two steps: 1) molding of an elastomeric matrix containing free-form microfluidic channels and 2) injection of a liquid conductive material that acts as an electrode. The feasibility of our method is investigated via the fabrication and characterization of simple monolithic DEAs with multiple electrodes (2, 4, and 10). The fabricated actuators are characterized in terms of actuation stroke, output force, and frequency response. In the actuators, polydimethylsiloxane (PDMS) and eutectic gallium-indium (EGaIn) are used for the elastomeric matrix and electrode material, respectively. Microfluidic channels are realized by dissolving a three-dimensional printed part suspended in the elastomeric structure. The experimental results show the successful implementation of the proposed method and the good agreement between the measured data and theoretical predication, validating the feasibility of the proposed method.

Phase Changing Materials-Based Variable-Stiffness Tensegrity Structures.

Soft robots leverage deformable bodies to achieve different types of locomotion, improve transportability, and safely navigate cluttered environments. In this context, variable-stiffness structures provide soft robots with additional properties, such as the ability to increase forces transmitted to the environment, to lock into different body configurations, and to reduce the number of actuators required for morphological change. Tensegrity structures have been recently proposed as a biologically inspired design principle for soft robots. However, the few examples of tensegrity structures with variable stiffness displayed relatively small stiffness change (i.e., by a factor of 3) or resorted to multiple and bulky actuators. In this article, we describe a novel design approach to variable-stiffness tensegrity structures (VSTSs) that relies on the use of variable-stiffness cables (VSCs). As an example, we describe the design and implementation of a three-strut tensegrity structure with VSCs made of low melting point alloys. The resulting VSTS displays unprecedented stiffness changes by a factor of 28 in compression and 13 in bending. We show the capabilities of the proposed VSTS in three validation scenarios with different tensegrity architectures: (1) a beam with tunable load-bearing capability, (2) a structure that can self-deploy and lock its shape in both deployed and undeployed states, and (3) a joint with underactuated shape deformations.

Sensitivity Improvement of Highly Stretchable Capacitive Strain Sensors by Hierarchical Auxetic Structures.

Highly stretchable sensors that can detect large strains are useful in deformable systems, such as soft robots and wearable devices. For stretchable strain sensors, two types of sensing methods exist, namely, resistive and capacitive. Capacitive sensing has several advantages over the resistive type, such as high linearity, repeatability, and low hysteresis. However, the sensitivity (gauge factor) of capacitive strain sensors is theoretically limited to 1, which is much lower than that of the resistive-type sensors. The objective of this study is to improve the sensitivity of highly stretchable capacitive strain sensors by integrating hierarchical auxetic structures into them. Auxetic structures have a negative Poisson's ratio that causes increase in change in capacitance with applied strains, and thereby improving sensitivity. In order to prove this concept, we fabricate and characterize two sensor samples with planar dimensions 60 mm × 16 mm. The samples have an acrylic elastomer (3M, VHB 4905) as the dielectric layer and a liquid metal (eutectic gallium-indium) for electrodes. On both sides of the sensor samples, hierarchical auxetic structures made of a silicone elastomer (Dow Corning, Sylgard 184) are attached. The samples are tested under strains up to 50% and the experimental results show that the sensitivity of the sensor with the auxetic structure exceeds the theoretical limit. In addition, it is observed that the sensitivity of this sensor is roughly two times higher than that of a sensor without the auxetic structure, while maintaining high linearity (R 2 = 0.995), repeatability (≥104 cycles), and low hysteresis.

Bioinspired dual-stiffness origami.

Origami manufacturing has led to considerable advances in the field of foldable structures with innovative applications in robotics, aerospace, and metamaterials. However, existing origami are either load-bearing structures that are prone to tear and fail if overloaded or resilient soft structures with limited load capability. In this manuscript, we describe an origami structure that displays both high load bearing and high resilience characteristics. The structure, which is inspired by insect wings, consists of a prestretched elastomeric membrane, akin to the soft resilin joints of insect wings, sandwiched between rigid tiles, akin to the rigid cuticles of insect wings. The dual-stiffness properties of the proposed structure are validated by using the origami as an element of a quadcopter frame that can withstand aerodynamic forces within its flight envelope but softens during collisions to avoid permanent damage. In addition, we demonstrate an origami gripper that can be used for rigid grasping but softens to avoid overloading of the manipulated objects.

Soft Robotic Grippers.

Advances in soft robotics, materials science, and stretchable electronics have enabled rapid progress in soft grippers. Here, a critical overview of soft robotic grippers is presented, covering different material sets, physical principles, and device architectures. Soft gripping can be categorized into three technologies, enabling grasping by: a) actuation, b) controlled stiffness, and c) controlled adhesion. A comprehensive review of each type is presented. Compared to rigid grippers, end-effectors fabricated from flexible and soft components can often grasp or manipulate a larger variety of objects. Such grippers are an example of morphological computation, where control complexity is greatly reduced by material softness and mechanical compliance. Advanced materials and soft components, in particular silicone elastomers, shape memory materials, and active polymers and gels, are increasingly investigated for the design of lighter, simpler, and more universal grippers, using the inherent functionality of the materials. Embedding stretchable distributed sensors in or on soft grippers greatly enhances the ways in which the grippers interact with objects. Challenges for soft grippers include miniaturization, robustness, speed, integration of sensing, and control. Improved materials, processing methods, and sensing play an important role in future research.

Soft Biomimetic Fish Robot Made of Dielectric Elastomer Actuators.

This article presents the design, fabrication, and characterization of a soft biomimetic robotic fish based on dielectric elastomer actuators (DEAs) that swims by body and/or caudal fin (BCF) propulsion. BCF is a promising locomotion mechanism that potentially offers swimming at higher speeds and acceleration rates, and efficient locomotion. The robot consists of laminated silicone layers wherein two DEAs are used in an antagonistic configuration, generating undulating fish-like motion. The design of the robot is guided by a mathematical model based on the Euler-Bernoulli beam theory and takes account of the nonuniform geometry of the robot and of the hydrodynamic effect of water. The modeling results were compared with the experimental results obtained from the fish robot with a total length of 150 mm, a thickness of 0.75 mm, and weight of 4.4 g. We observed that the frequency peaks in the measured thrust force produced by the robot are similar to the natural frequencies computed by the model. The peak swimming speed of the robot was 37.2 mm/s (0.25 body length/s) at 0.75 Hz. We also observed that the modal shape of the robot at this frequency corresponds to the first natural mode. The swimming of the robot resembles real fish and displays a Strouhal number very close to those of living fish. These results suggest the high potential of DEA-based underwater robots relying on BCF propulsion, and applicability of our design and fabrication methods.