Features of the Formation of Sensitive Films Based on Mycelium of Higher Fungi for Surface and Plate Acoustic Waves Gas Sensors.

A comparative analysis of the responses of two types of acoustic waves (surface SAW and plate APW) with close frequencies and the same type of waves (SAW) with different frequencies toward various liquid vapors (water, acetone, ethanol) was carried out in this paper. Two types of films based on mycelium of higher fungus Ganoderma lucidum (Curtis) P. Karst (G. lucidum) prepared by various methods were used as sensitive coatings. These films were based on G. lucidum mycelium ethanolic (48% v/v) homogenizate (MEGl) and extract (EGl). A film deposition procedure compatible with acoustic devices technology was developed. Various piezoelectric substrates (YX-LiNbO3, 128 YX-LiNbO3) were used for appropriate acoustic delay lines production. It was found that additional SAW and APW attenuation associated with the appearance of mycelium films on the surface of the acoustic waveguide is two times greater for MEGL than for EGL films in the frequency range of 20-80 MHz The changes in acoustic wave amplitude and phase due to vapor absorption were measured and compared with each other, taking into account the differences in geometry of the samples. It was found that the phase response of the SAW delay lines with EGL films is three times higher than one with the presence of MEGL films for water and ethanol vapors. The films used are demonstrated good reproducibility and long-term stability for at least 2 months. Based on the results obtained, it was concluded that MEGl film is not appropriate for use in high frequency SAW delay lines as a sensitive coating. However, both types of the films (MEGl and EGl) could be used as sensitive coatings for low frequency SAW and APW sensors based on corresponding delay lines. Additionally, it was found that the films used are not sensitive to acetone vapor. As a result of the work carried out, a technique for creating sensitive films based on the mycelium of higher fungi compatible with the planar technology of acoustoelectronic delay lines was developed. The possibility of using such films for the development of gas SAW and APW sensors was shown.

Electrocatalytic CO2 Reduction on CuOx Nanocubes: Tracking the Evolution of Chemical State, Geometric Structure, and Catalytic Selectivity using Operando Spectroscopy.

The direct electrochemical conversion of carbon dioxide (CO2 ) into multi-carbon (C2+ ) products still faces fundamental and technological challenges. While facet-controlled and oxide-derived Cu materials have been touted as promising catalysts, their stability has remained problematic and poorly understood. Herein we uncover changes in the chemical and morphological state of supported and unsupported Cu2 O nanocubes during operation in low-current H-Cells and in high-current gas diffusion electrodes (GDEs) using neutral pH buffer conditions. While unsupported nanocubes achieved a sustained C2+ Faradaic efficiency of around 60 % for 40 h, the dispersion on a carbon support sharply shifted the selectivity pattern towards C1 products. Operando XAS and time-resolved electron microscopy revealed the degradation of the cubic shape and, in the presence of a carbon support, the formation of small Cu-seeds during the surprisingly slow reduction of bulk Cu2 O. The initially (100)-rich facet structure has presumably no controlling role on the catalytic selectivity, whereas the oxide-derived generation of under-coordinated lattice defects, can support the high C2+ product yields.

Operando NRIXS and XAFS Investigation of Segregation Phenomena in Fe-Cu and Fe-Ag Nanoparticle Catalysts during CO2 Electroreduction.

Operando nuclear resonant inelastic X-ray scattering (NRIXS) and X-ray absorption fine-structure spectroscopy (XAFS) measurements were used to gain insight into the structure and surface composition of FeCu and FeAg nanoparticles (NPs) during the electrochemical CO2 reduction (CO2 RR) and to extract correlations with their catalytic activity and selectivity. The formation of a core-shell structure during CO2 RR for FeAg NPs was inferred from the analysis of the operando NRIXS data (phonon density of states, PDOS) and XAFS measurements. Electrochemical analysis of the FeAg NPs revealed a faradaic selectivity of 36 % for CO in 0.1 M KHCO3 at -1.1 V vs. RHE, similar to that of pure Ag NPs. In contrast, a predominant selectivity towards H2 evolution is obtained in the case of the FeCu NPs, analogous to the results obtained for pure Fe NPs, although small Cu NPs have also been shown to favor H2 production.

Enhanced Stability and CO/Formate Selectivity of Plasma-Treated SnO x/AgO x Catalysts during CO2 Electroreduction.

CO2 electroreduction into useful chemicals and fuels is a promising technology that might be used to minimize the impact that the increasing industrial CO2 emissions are having on the environment. Although plasma-oxidized silver surfaces were found to display a considerably decreased overpotential for the production of CO, the hydrogen evolution reaction (HER), a competing reaction against CO2 reduction, was found to increase over time. More stable and C1-product-selective SnO x/AgO x catalysts were obtained by electrodepositing Sn on O2-plasma-pretreated Ag surfaces. In particular, a strong suppression of HER (below 5% Faradaic efficiency (FE) at -0.8 V vs the reversible hydrogen electrode, RHE) during 20 h was observed. Ex situ scanning electron microscopy (SEM) combined with energy-dispersive X-ray spectroscopy (EDS), quasi in situ X-ray photoelectron spectroscopy (XPS), and operando X-ray absorption near-edge structure spectroscopy (XANES) measurements showed that our synthesis led to a highly roughened surface containing stable Snδ+/Sn species that were found to be key in the enhanced activity and stable CO/formate (HCOO-) selectivity. Our study highlights the importance of roughness, composition, and chemical state effects in CO2 electrocatalysis.

Operando Insight into the Correlation between the Structure and Composition of CuZn Nanoparticles and Their Selectivity for the Electrochemical CO2 Reduction.

Bimetallic CuZn catalysts have been recently proposed as alternatives in order to achieve selectivity control during the electrochemical reduction of CO2 (CO2RR). However, fundamental understanding of the underlying reaction mechanism and parameters determining the CO2RR performance is still missing. In this study, we have employed size-controlled (∼5 nm) Cu100-xZnx nanoparticles (NPs) supported on carbon to investigate the correlation between their structure and composition and catalytic performance. By tuning the concentration of Zn, a drastic increase in CH4 selectivity [∼70% Faradaic efficiency (F.E.)] could be achieved for Zn contents from 10 to 50, which was accompanied by a suppression of the H2 production. Samples containing a higher Zn concentration displayed significantly lower CH4 production and an abrupt switch in the selectivity to CO. Lack of metal leaching was observed based on quasi in situ X-ray photoelectron spectroscopy (XPS). Operando X-ray absorption fine structure (XAFS) spectroscopy measurements revealed that the alloying of Cu atoms with Zn atoms takes place under reaction conditions and plays a determining role in the product selectivity. Time-dependent XAFS analysis showed that the local structure and chemical environment around the Cu atoms continuously evolve during CO2RR for several hours. In particular, cationic Zn species initially present were found to get reduced as the reaction proceeded, leading to the formation of a CuZn alloy (brass). The evolution of the Cu-Zn interaction with time during CO2RR was found to be responsible for the change in the selectivity from CH4 over Cu-ZnO NPs to CO over CuZn alloy NPs. This study highlights the importance of having access to in depth information on the interplay between the different atomic species in bimetallic NP electrocatalysts under operando reaction conditions in order to understand and ultimately tune their reactivity.

Selective CO2 Electroreduction to Ethylene and Multicarbon Alcohols via Electrolyte-Driven Nanostructuring.

Production of multicarbon products (C2+ ) from CO2 electroreduction reaction (CO2 RR) is highly desirable for storing renewable energy and reducing carbon emission. The electrochemical synthesis of CO2 RR catalysts that are highly selective for C2+ products via electrolyte-driven nanostructuring is presented. Nanostructured Cu catalysts synthesized in the presence of specific anions selectively convert CO2 into ethylene and multicarbon alcohols in aqueous 0.1 m KHCO3 solution, with the iodine-modified catalyst displaying the highest Faradaic efficiency of 80 % and a partial geometric current density of ca. 31.2 mA cm-2 for C2+ products at -0.9 V vs. RHE. Operando X-ray absorption spectroscopy and quasi in situ X-ray photoelectron spectroscopy measurements revealed that the high C2+ selectivity of these nanostructured Cu catalysts can be attributed to the highly roughened surface morphology induced by the synthesis, presence of subsurface oxygen and Cu+ species, and the adsorbed halides.

Operando Evolution of the Structure and Oxidation State of Size-Controlled Zn Nanoparticles during CO2 Electroreduction.

We explored the size-dependent activity and selectivity of Zn nanoparticles (NPs) for the electrochemical CO2 reduction reaction (CO2RR). Zn NPs ranging from 3 to 5 nm showed high activity and selectivity (∼70%) for CO production, whereas those above 5 nm exhibited bulk-like catalytic properties. In addition, a drastic increase in hydrogen production was observed for the Zn NPs below 3 nm, which is associated with the enhanced content of low-coordinated sites on small NPs. The presence of residual cationic Zn species in the catalysts was also revealed during CO2RR via operando X-ray absorption fine-structure spectroscopy measurements. Such species are expected to play a role in the selectivity trends obtained. Our findings can serve as guidance for the development of highly active and CO-selective Zn-based catalysts for CO2RR.

Dynamic Changes in the Structure, Chemical State and Catalytic Selectivity of Cu Nanocubes during CO2 Electroreduction: Size and Support Effects.

In situ and operando spectroscopic and microscopic methods were used to gain insight into the correlation between the structure, chemical state, and reactivity of size- and shape-controlled ligand-free Cu nanocubes during CO2 electroreduction (CO2 RR). Dynamic changes in the morphology and composition of Cu cubes supported on carbon were monitored under potential control through electrochemical atomic force microscopy, X-ray absorption fine-structure spectroscopy and X-ray photoelectron spectroscopy. Under reaction conditions, the roughening of the nanocube surface, disappearance of the (100) facets, formation of pores, loss of Cu and reduction of CuOx species observed were found to lead to a suppression of the selectivity for multi-carbon products (i.e. C2 H4 and ethanol) versus CH4 . A comparison with Cu cubes supported on Cu foils revealed an enhanced morphological stability and persistence of CuI species under CO2 RR in the former samples. Both factors are held responsible for the higher C2 /C1 product ratio observed for the Cu cubes/Cu as compared to Cu cubes/C. Our findings highlight the importance of the structure of the active nanocatalyst but also its interaction with the underlying substrate in CO2 RR selectivity.

Operando Phonon Studies of the Protonation Mechanism in Highly Active Hydrogen Evolution Reaction Pentlandite Catalysts.

Synthetic pentlandite (Fe4.5Ni4.5S8) is a promising electrocatalyst for hydrogen evolution, demonstrating high current densities, low overpotential, and remarkable stability in bulk form. The depletion of sulfur from the surface of this catalyst during the electrochemical reaction has been proposed to be beneficial for its catalytic performance, but the role of sulfur vacancies and the mechanism determining the reaction kinetics are still unknown. We have performed electrochemical operando studies of the vibrational dynamics of pentlandite under hydrogen evolution reaction conditions using 57Fe nuclear resonant inelastic X-ray scattering. Comparing the measured Fe partial vibrational density of states with density functional theory calculations, we have demonstrated that hydrogen atoms preferentially occupy substitutional positions replacing pre-existing sulfur vacancies. Once all vacancies are filled, the protonation proceeds interstitially, which slows down the reaction. Our results highlight the beneficial role of sulfur vacancies in the electrocatalytic performance of pentlandite and give insights into the hydrogen adsorption mechanism during the reaction.

Enhanced Carbon Dioxide Electroreduction to Carbon Monoxide over Defect-Rich Plasma-Activated Silver Catalysts.

Efficient, stable catalysts with high selectivity for a single product are essential if electroreduction of CO2 is to become a viable route to the synthesis of industrial feedstocks and fuels. A plasma oxidation pre-treatment of silver foil enhances the number of low-coordinated catalytically active sites, which dramatically lowers the overpotential and increases the activity of CO2 electroreduction to CO. At -0.6 V versus RHE more than 90 % Faradaic efficiency towards CO was achieved on a pre-oxidized silver foil. While transmission electron microscopy (TEM) and operando X-ray absorption spectroscopy showed that oxygen species can survive in the bulk of the catalyst during the reaction, quasi in situ X-ray photoelectron spectroscopy showed that the surface is metallic under reaction conditions. DFT calculations reveal that the defect-rich surface of the plasma-oxidized silver foils in the presence of local electric fields drastically decrease the overpotential of CO2 electroreduction.

One-Pot Synthesis of Carbon-Coated Nanostructured Iron Oxide on Few-Layer Graphene for Lithium-Ion Batteries.

Nanostructure engineering has been demonstrated to improve the electrochemical performance of iron oxide based electrodes in Li-ion batteries (LIBs). However, the synthesis of advanced functional materials often requires multiple steps. Herein, we present a facile one-pot synthesis of carbon-coated nanostructured iron oxide on few-layer graphene through high-pressure pyrolysis of ferrocene in the presence of pristine graphene. The ferrocene precursor supplies both iron and carbon to form the carbon-coated iron oxide, while the graphene acts as a high-surface-area anchor to achieve small metal oxide nanoparticles. When evaluated as a negative-electrode material for LIBs, our composite showed improved electrochemical performance compared to commercial iron oxide nanopowders, especially at fast charge/discharge rates.

Strategies to design efficient silica-supported photocatalysts for reduction of CO2.

The photocatalytic reduction of CO2 by water vapor to produce light hydrocarbons was studied over a series of catalysts consisting of variable loading of Ti incorporated in TUD-1 mesoporous silica, either modified by ZnO nanoparticles or isolated Cr-sites. Unexpectedly, the performance of ZnO-Ti-TUD-1 and Cr-Ti-TUD-1 was inferior to the parent Ti-TUD-1. An explanation can be found in experiments on the photocatalytic degradation of a mixture of hydrocarbons (i.e., CH4, C2H4, C2H6, C3H6, and C3H8) under the same illumination conditions. Ti-TUD-1 exhibits the poorest activity in hydrocarbon degradation, while ZnO-Ti-TUD-1 and Cr-Ti-TUD-1 showed very significant degradation rates. This study clearly demonstrates the importance of evaluating hydrocarbon conversion over photocatalysts active in converting CO2 to hydrocarbons (in batch reactors).

Low-temperature oxidation of carbon monoxide with gold(III) ions supported on titanium oxide.

Au/TiO2 catalysts prepared by a deposition-precipitation process and used for CO oxidation without previous calcination exhibited high, largely temperature-independent conversions at low temperatures, with apparent activation energies of about zero. Thermal treatments, such as He at 623 K, changed the conversion-temperature characteristics to the well-known S-shape, with activation energies slightly below 30 kJ mol(-1). Sample characterization by XAFS and electron microscopy and a low-temperature IR study of CO adsorption and oxidation showed that CO can be oxidized by gas-phase O2 at 90 K already over the freeze-dried catalyst in the initial state that contained Au exclusively in the +3 oxidation state. CO conversion after activation in the feed at 303 K is due to Au(III)-containing sites at low temperatures, while Au(0) dominates conversion at higher temperatures. After thermal treatments, CO conversion in the whole investigated temperature range results from sites containing exclusively Au(0).

Mn(x)O(y)/NC and Co(x)O(y)/NC nanoparticles embedded in a nitrogen-doped carbon matrix for high-performance bifunctional oxygen electrodes.

Reversible interconversion of water into H2 and O2, and the recombination of H2 and O2 to H2O thereby harnessing the energy of the reaction provides a completely green cycle for sustainable energy conversion and storage. The realization of this goal is however hampered by the lack of efficient catalysts for water splitting and oxygen reduction. We report exceptionally active bifunctional catalysts for oxygen electrodes comprising Mn3O4 and Co3O4 nanoparticles embedded in nitrogen-doped carbon, obtained by selective pyrolysis and subsequent mild calcination of manganese and cobalt N4 macrocyclic complexes. Intimate interaction was observed between the metals and nitrogen suggesting residual M-N(x) coordination in the catalysts. The catalysts afford remarkably lower reversible overpotentials in KOH (0.1 M) than those for RuO2, IrO2, Pt, NiO, Mn3O4, and Co3O4, thus placing them among the best non-precious-metal catalysts for reversible oxygen electrodes reported to date.

Anion-Exchange Membrane "Polikon A" Based on Polyester Fiber Fabric (Functionalized by Low-Temperature High-Frequency Plasma) with Oxidized Metal Nanoparticles.

An experimental laboratory set of samples of composite heterogeneous anion-exchange membranes was obtained by us for the development of our original method of polycondensation filling. Anion-exchange membranes were prepared on plasma-treated and non-plasma-treated polyester fiber fabrics. The fabric was treated with low-temperature argon plasma at a power of 400 W for 10 min at a pressure of 5 × 10-5 mbar. On the surface and bulk of the polyester fiber, a polyfunctional anionite of mixed basicity was synthesized and formed. The anion-exchange membrane contained secondary and tertiary amino groups and quaternary ammonium groups, which were obtained from polyethylene polyamines and epichlorohydrins. At the stage of the chemical synthesis of the anion matrix, oxidized nanoparticles (~1.5 wt.%) of silicon, nickel, and iron were added to the monomerization composition. The use of ion-plasma processing of fibers in combination with the introduction of oxidized nanoparticles at the synthesis stage makes it possible to influence the speed and depth of the synthesis and curing processes; this changes the formation of the surface morphology and the internal structure of the ion-exchange polymer matrix, as well as the hydrophobic/hydrophilic balance and-as a result-the different operational characteristics of anion-exchange membranes.

Operando high-pressure investigation of size-controlled CuZn catalysts for the methanol synthesis reaction.

Although Cu/ZnO-based catalysts have been long used for the hydrogenation of CO2 to methanol, open questions still remain regarding the role and the dynamic nature of the active sites formed at the metal-oxide interface. Here, we apply high-pressure operando spectroscopy methods to well-defined Cu and Cu0.7Zn0.3 nanoparticles supported on ZnO/Al2O3, γ-Al2O3 and SiO2 to correlate their structure, composition and catalytic performance. We obtain similar activity and methanol selectivity for Cu/ZnO/Al2O3 and CuZn/SiO2, but the methanol yield decreases with time on stream for the latter sample. Operando X-ray absorption spectroscopy data reveal the formation of reduced Zn species coexisting with ZnO on CuZn/SiO2. Near-ambient pressure X-ray photoelectron spectroscopy shows Zn surface segregation and the formation of a ZnO-rich shell on CuZn/SiO2. In this work we demonstrate the beneficial effect of Zn, even in diluted form, and highlight the influence of the oxide support and the Cu-Zn interface in the reactivity.

Linking the evolution of catalytic properties and structural changes in copper-zinc nanocatalysts using operando EXAFS and neural-networks.

Understanding the evolution of unique structural motifs in bimetallic catalysts under reaction conditions, and linking them to the observed catalytic properties is necessary for the rational design of the next generation of catalytic materials. Extended X-ray absorption fine structure (EXAFS) spectroscopy is a premier experimental method to address this issue, providing the possibility to track the changes in the structure of working catalysts. Unfortunately, the intrinsic heterogeneity and enhanced disorder characteristic of catalytic materials experiencing structural transformations under reaction conditions, as well as the low signal-to-noise ratio that is common for in situ EXAFS spectra hinder the application of conventional data analysis approaches. Here we address this problem by employing machine learning methods (artificial neural networks) to establish the relationship between EXAFS features and structural motifs in metals as well as oxide materials. We apply this approach to time-dependent EXAFS spectra acquired from copper-zinc nanoparticles during the electrochemical reduction of CO2 to reveal the details of the composition-dependent structural evolution and brass alloy formation, and their correlation with the catalytic selectivity of these materials.

In-situ structure and catalytic mechanism of NiFe and CoFe layered double hydroxides during oxygen evolution.

NiFe and CoFe (MFe) layered double hydroxides (LDHs) are among the most active electrocatalysts for the alkaline oxygen evolution reaction (OER). Herein, we combine electrochemical measurements, operando X-ray scattering and absorption spectroscopy, and density functional theory (DFT) calculations to elucidate the catalytically active phase, reaction center and the OER mechanism. We provide the first direct atomic-scale evidence that, under applied anodic potentials, MFe LDHs oxidize from as-prepared α-phases to activated γ-phases. The OER-active γ-phases are characterized by about 8% contraction of the lattice spacing and switching of the intercalated ions. DFT calculations reveal that the OER proceeds via a Mars van Krevelen mechanism. The flexible electronic structure of the surface Fe sites, and their synergy with nearest-neighbor M sites through formation of O-bridged Fe-M reaction centers, stabilize OER intermediates that are unfavorable on pure M-M centers and single Fe sites, fundamentally accounting for the high catalytic activity of MFe LDHs.

Plasma-Modified Dendritic Cu Catalyst for CO2 Electroreduction.

Efficient and active catalysts with high selectivity for hydrocarbons and other valuable chemicals during stable operation are crucial. We have taken advantage of low-pressure oxygen plasmas to modify dendritic Cu catalysts and were able to achieve enhanced selectivity toward C2 and C3 products. Utilizing operando spectroscopic methods such as X-ray absorption fine-structure spectroscopy (XAFS) and quasi in situ X-ray photoelectron spectroscopy (XPS), we observed that the initial presence of oxides in these catalysts before the reaction plays an inferior role in determining their catalytic performance as compared to the overall catalyst morphology. This is assigned to the poor stability of the Cu x O species in these materials under the conditions of electrocatalytic conversion of CO2 (CO2RR). Our findings shed light into the strong structure/chemical state-selectivity correlation in CO2RR and open venues for the rational design of more effective catalysts through plasma pretreatments.

Bio-inspired design: bulk iron-nickel sulfide allows for efficient solvent-dependent CO2 reduction.

The electrocatalytic reduction of carbon dioxide (CO2RR) to valuable bulk chemicals is set to become a vital factor in the prevention of environmental pollution and the selective storage of sustainable energy. Inspired by structural analogues to the active site of the enzyme CODHNi, we envisioned that bulk Fe/Ni sulfides would enable the efficient reduction of CO2. By careful adjustment of the process conditions, we demonstrate that pentlandite (Fe4.5Ni4.5S8) electrodes, in addition to HER, also support the CO2RR reaching a peak faradaic efficiency of 87% and 13% for the formation of CO and methane, respectively at 3 mA cm-2. The choice of solvent, the presence of water/protons and CO2 solubility are identified as key-properties to adjust the balance between HER and CO2RR in favour of the latter. Such experiments can thus serve as model reactions to elucidate a potential catalyst within gas diffusion electrodes.