MAX Phase (Nb4 AlC3 ) For Electrocatalysis Applications.

In search for novel materials to replace noble metal-based electrocatalysts in electrochemical energy conversion and storage devices, special attention is given to a distinct class of materials, MAX phase that combines advantages of ceramic and metallic properties. Herein, Nb4 AlC3 MAX phase is prepared by a solid-state mixing reaction and characterized morphologically and structurally by transmission and scanning electron microscopy with energy-dispersive X-ray spectroscopy, nitrogen-sorption, X-ray diffraction analysis, X-ray photoelectron and Raman spectroscopy. Electrochemical performance of Nb4 AlC3 in terms of capacitance as well as for oxygen reduction reaction (ORR) and hydrogen evolution reaction (HER) is evaluated in different electrolytes. The specific capacitance Cs of 66.4, 55.0, and 46.0 F g-1 at 5 mV s-1 is determined for acidic, neutral and alkaline medium, respectively. Continuous cycling reveals high capacitance retention in three electrolyte media; moreover, increase of capacitance is observed in acidic and neutral media. The electrochemical impedance spectroscopy showed a low charge transfer resistance of 64.76 Ω cm2 that resulted in better performance for HER in acidic medium (Tafel slope of 60 mV dec-1 ). In alkaline media, the charge storage value in the double layer is 360 mF cm-2 (0.7 V versus reversible hydrogen electrode) and the best ORR performance of the Nb4 AlC3 is achieved in this medium (Tafel slope of 126 mV dec-1 ).

Electrocatalytic Behavior of an Amide Functionalized Mn(II) Coordination Polymer on ORR, OER and HER.

The new 3D coordination polymer (CP) [Mn(L)(HCOO)]n (Mn-CP) [L = 4-(pyridin-4-ylcarbamoyl)benzoate] was synthesised via a hydrothermal reaction using the pyridyl amide functionalized benzoic acid HL. It was characterized by elemental, FT-IR spectroscopy, single-crystal and powder X-ray diffraction (PXRD) analyses. Its structural features were disclosed by single-crystal X-ray diffraction analysis, which revealed a 3D structure with the monoclinic space group P21/c. Its performance as an electrocatalyst for oxygen reduction (ORR), oxygen evolution (OER), and hydrogen evolution (HER) reactions was tested in both acidic (0.5 M H2SO4) and alkaline (0.1 M KOH) media. A distinct reduction peak was observed at 0.53 V vs. RHE in 0.1 M KOH, which corresponds to the oxygen reduction, thus clearly demonstrating the material's activity for the ORR. Tafel analysis revealed a Tafel slope of 101 mV dec-1 with mixed kinetics of 2e- and 4e- pathways indicated by the Koutecky-Levich analysis. Conversely, the ORR peak was not present in 0.5 M H2SO4 indicating no activity of Mn-CP for this reaction in acidic media. In addition, Mn-CP demonstrated a noteworthy activity toward OER and HER in acidic media, in contrast to what was observed in 0.1 M KOH.

Full-Self-Powered Humidity Sensor Based on Electrochemical Aluminum-Water Reaction.

A detailed examination of the principle of operation behind the functioning of the full-self-powered humidity sensor is presented. The sensor has been realized as a structure consisting of an interdigitated capacitor with aluminum thin-film digits. In this work, the details of its fabrication and activation are described in detail. The performed XRD, FTIR, SEM, AFM, and EIS analyses, as well as noise measurements, revealed that the dominant process of electricity generation is the electrochemical reaction between the sensor's aluminum electrodes and the water from humid air in the presence of oxygen, which was the main goal of this work. The response of the sensor to human breath is also presented as a demonstration of its possible practical application.

Versatility of Amide-Functionalized Co(II) and Ni(II) Coordination Polymers: From Thermochromic-Triggered Structural Transformations to Supercapacitors and Electrocatalysts for Water Splitting.

The new 2D coordination polymers (CPs) [M(L)2(H2O)2]n [M = CoII (1) and NiII (2); L = 4-(pyridin-3-ylcarbamoyl)benzoate] were synthesized from pyridyl amide-functionalized benzoic acid (HL). They were characterized by elemental, Fourier transform infrared, thermogravimetric, powder X-ray diffraction (PXRD), and single-crystal X-ray diffraction (XRD) structural analyses. Single-crystal XRD analysis revealed the presence of a 2D polymeric architecture, and topological analyses disclose a 2,4-connected binodal net. A thermochromic effect leads to the production of two new CPs, 1' and 2', by heating at ca. 220 °C, accompanied by a color change from orange to purple in the case of 1 and from blue to green in the case of 2. The transformation of 1 to 1' takes place through an intermediate (1a) with a different twist of the L- ligand, leading to the formation of a 1D polymeric architecture, as proven by single-crystal XRD analysis. The addition of water or keeping 1' or 2' in air for several days leads to regeneration of 1 or 2, respectively. The thermochromic-triggered structural transformations of 1 and 2 were further substantiated by PXRD and UV-vis ground-state diffuse-reflectance absorption studies. The supercapacitance ability of the CPs 1 and 2 and a Ni-Co composite (made from mixing the CPs 1 and 2) was investigated by electroanalytical techniques, such as cyclic voltammetry and electrochemical impedance spectroscopy. The CP 2 exhibits the highest specific capacity of 273.8 C g-1 at an applied current density of 1.5 A g-1. These newly developed CPs further act as electrocatalysts for the water-splitting reaction.

Electrochemical Sensing of Cadmium and Lead Ions in Water by MOF-5/PANI Composites.

For the first time, composites of metal-organic framework MOF-5 and conjugated polymer polyaniline (PANI), (MOF-5/PANI), prepared using PANI in its conducting (emeraldine salt, ES) or nonconducting form (emeraldine base, EB) at various MOF-5 and PANI mass ratios, were evaluated as electrode materials for the electrochemical detection of cadmium (Cd2+) and lead (Pb2+) ions in aqueous solutions. Testing of individual components of composites, PANI-ES, PANI-EB, and MOF-5, was also performed for comparison. Materials are characterized by Raman spectroscopy, scanning electron microscopy (SEM) and dynamic light scattering (DLS), and their electrochemical behavior was discussed in terms of their zeta potential, structural, morphology, and textural properties. All examined composites showed high electrocatalytic activity for the oxidation of Cd and Pb to Cd2+ and Pb2+, respectively. The MOF/EB-1 composite (71.0 wt.% MOF-5) gave the highest oxidation currents during both individual and simultaneous detection of two heavy metal ions. Current densities recorded with MOF/EB-1 were also higher than those of its individual components, reflecting the synergistic effect where MOF-5 offers high surface area for two heavy metals adsorption and PANI offers a network for electron transfer during metals' subsequent oxidation. Limits of detection using MOF/EB-1 electrode for Cd2+ and Pb2+ sensing were found to be as low as 0.077 ppm and 0.033 ppm, respectively. Moreover, the well-defined and intense peaks of Cd oxidation to Cd2+ and somewhat lower peaks of Pb oxidation to Pb2+ were observed at voltammograms obtained for the Danube River as a real sample with no pretreatment, which implies that herein tested MOF-5/PANI electrodes could be used as electrochemical sensors for the detection of heavy metal ions in the real water samples.

A mixed-ligand Co metal-organic framework and its carbon composites as excellent electrocatalysts for the oxygen evolution reaction in green-energy devices.

Oxygen evolution reaction (OER) electrocatalysts are frequently made from noble metal-based oxides like ruthenium/iridium oxides. However, because of their scarcity and high price, researchers are now focusing on creating innovative OER catalysts based on affordable transition metals that have improved electrical conductivity and accessibility to active sites. Metal-organic frameworks (MOFs), a unique class of inorganic materials with excellent physical and chemical properties, have witnessed significant progress in promising green energy systems. In this work, a novel mixed-ligand metal-organic framework [Co(µ-1κN,2κN'-BDP)(µ3-1κoo',2κo''2κo'''-BTC)]n·nH2O (BDP = boron-dipyrromethene or BODIPY; BTC = benzene tricarboxylate) denoted as CoBDPMOF has been synthesized, and its composites with different carbon materials have been designed. Compared to the pristine MOF, the composites showed enhanced electrocatalytic activity toward the oxygen evolution reaction (OER) in alkaline media. In addition, the CoBDPMOF with activated carbon showed the highest OER performance with a low Tafel slope (82 mV dec-1) and the highest j600 (59.8 mA cm-2), outperforming noble metal IrO2, the OER benchmark electrocatalyst. This study presents new insights into the design and application of CoBDPMOF-based materials for energy conversion and suggests promising avenues for further research and development in electrocatalysis.

Bipolar Membranes for Direct Borohydride Fuel Cells-A Review.

Direct liquid fuel cells (DLFCs) operate directly on liquid fuel instead of hydrogen, as in proton-exchange membrane fuel cells. DLFCs have the advantages of higher energy densities and fewer issues with the transportation and storage of their fuels compared with compressed hydrogen and are adapted to mobile applications. Among DLFCs, the direct borohydride-hydrogen peroxide fuel cell (DBPFC) is one of the most promising liquid fuel cell technologies. DBPFCs are fed sodium borohydride (NaBH4) as the fuel and hydrogen peroxide (H2O2) as the oxidant. Introducing H2O2 as the oxidant brings further advantages to DBPFC regarding higher theoretical cell voltage (3.01 V) than typical direct borohydride fuel cells operating on oxygen (1.64 V). The present review examines different membrane types for use in borohydride fuel cells, particularly emphasizing the importance of using bipolar membranes (BPMs). The combination of a cation-exchange membrane (CEM) and anion-exchange membrane (AEM) in the structure of BPMs makes them ideal for DBPFCs. BPMs maintain the required pH gradient between the alkaline NaBH4 anolyte and the acidic H2O2 catholyte, efficiently preventing the crossover of the involved species. This review highlights the vast potential application of BPMs and the need for ongoing research and development in DBPFCs. This will allow for fully realizing the significance of BPMs and their potential application, as there is still not enough published research in the field.

Effect of carbon support on the activity of monodisperse Co45Pt55 nanoparticles for oxygen evolution in alkaline media.

Oxygen evolution reaction (OER) represents the efficiency-limiting reaction in water electrolyzers, metal-air batteries, and unitized regenerative fuel cells. To achieve high-efficiency OER in alkaline media, we fabricated three novel electrocatalysts by the assembly of as-prepared Co45Pt55 alloy nanoparticles (NPs) on three different carbon-based support materials: reduced graphene oxide (CoPt/rGO), mesoporous graphitic carbon nitride (CoPt/mpg-CN), and commercial Ketjenblack carbon (CoPt/KB). Voltammetry studies revealed that CoPt/rGO electrocatalyst provided lower OER overpotentials accompanied by higher currents and specific current density values than the other two studied materials. Moreover, CoPt/rGO outperformed commercial CoPt/C electrocatalysts in terms of notably higher specific current densities. Additionally, it was found that CoPt/rGO electrocatalyst activity increases with increasing temperature up to 85°C, as suggested by the increase in the exchange current density. Electrochemical impedance spectroscopy studies of three electrocatalysts in OER revealed similar charge transfer resistance, although CoPt/rGO provided a higher current density. The main issue observed during long-term chronoamperometry and chronopotentiometry studies is the materials' instability under OER polarization conditions, which is still to be tackled in future work.

Highly Efficient Oxygen Electrode Obtained by Sequential Deposition of Transition Metal-Platinum Alloys on Graphene Nanoplatelets.

A set of platinum (Pt) and earth-abundant transition metals (M = Ni, Fe, Cu) on graphene nanoplatelets (sqPtM/GNPs) was synthesised via sequential deposition to establish parallels between the synthesis method and the materials' electrochemical properties. sqPtM/GNPs were assessed as bifunctional electrocatalysts for oxygen evolution (OER) and reduction (ORR) reactions for application in unitised regenerative fuel cells and metal-air batteries. sqPtFe/GNPs showed the highest catalytic performance with a low potential difference of ORR half-wave potential and overpotential at 10 mA cm-2 during OER, a crucial parameter for bifunctional electrocatalysts benchmarking. A novel two-stage synthesis strategy led to higher electrocatalytic performance by facilitating the reactants' access to the active sites and reducing the charge-transfer resistance.

Transformation of waste seed biomass of Cordia myxa into valuable bioenergy through membrane bioreactor using green nanoparticles of indium oxide.

Depletion of non-renewable fuel has obliged researchers to seek out sustainable and environmentally friendly alternatives. Membranes have proven to be an effective technique in biofuel production for reaction, purification, and separation, with the ability to use both porous and non-porous membranes. It is demonstrated that a membrane-based sustainable and green production can result in a high degree of process intensification, whereas the recovery and repurposing of catalysts and alcohol are anticipated to increase the process economics. Therefore, in this study sustainable biodiesel was synthesized from inedible seed oil (37 wt%) of Cordia myxa using a membrane reactor. Transesterification was catalyzed by heterogenous nano-catalyst of indium oxide prepared with leaf extract of Boerhavia diffusa. Highest biodiesel yield of 95 wt% was achieved at methanol to oil molar ratio of 7:1, catalyst load 0.8 wt%, temperature 82.5 °C and time 180 min In2O3 nanoparticles exhibited reusability up to five successive transesterification rounds. The production of methyl esters was confirmed using Fourier-transform infrared spectroscopy and Nuclear Magnetic Resonance. The predominant fatty acid methyl ester detected in the biodiesel was 5, 8-octadecenoic acid. Biodiesel fuel qualities were determined to be comparable to worldwide ASTM D-6571 and EN-14214 standards. Finally, it was concluded that membrane technology can result in a highly intensified reaction process while efficient recovery of both nano catalysts and methanol increases the economics of transesterification and lead to sustainable production.

Adsorption of bismuth ions on graphite chemically modified with gallic acid.

Graphite modified with gallic acid to form 'gallic acid-carbon' is demonstrated to be efficient for the removal of bismuth(III) ions from aqueous solutions. The uptake is demonstrated to be rapid but not to follow standard adsorption isotherm models. Instead, the uptake was found to be further promoted by the presence of the adsorbed metal. Additionally, the bismuth uptake showed linear dependence on the square of its concentration suggesting the possible formation of polymeric bismuth species. The gallic acid-carbon shows great promise as a relatively inexpensive material for solid-phase extraction and water purification with extraction efficiency close to 98%.

Steps towards highly-efficient water splitting and oxygen reduction using nanostructured ß-Ni(OH)2.

ß-Ni(OH)2 nanoplatelets are prepared by a hydrothermal procedure and characterized by scanning and transmission electron microscopy, X-ray diffraction analysis, Raman spectroscopy, and X-ray photoelectron spectroscopy. The material is demonstrated to be an efficient electrocatalyst for oxygen reduction, oxygen evolution, and hydrogen evolution reactions in alkaline media. ß-Ni(OH)2 shows an overpotential of 498 mV to reach 10 mA cm-2 towards oxygen evolution, with a Tafel slope of 149 mV dec-1 (decreasing to 99 mV dec-1 at 75 °C), along with superior stability as evidenced by chronoamperometric measurements. Similarly, a low overpotential of -333 mV to reach 10 mA cm-2 (decreasing to only -65 mV at 75 °C) toward hydrogen evolution with a Tafel slope of -230 mV dec-1 is observed. Finally, ß-Ni(OH)2 exhibits a noteworthy performance for the ORR, as evidenced by a low Tafel slope of -78 mV dec-1 and a number of exchanged electrons of 4.01 (indicating direct 4e--oxygen reduction), whereas there are only a few previous reports on modest ORR activity of pure Ni(OH)2.

Low Au-content CoAu electrodes for environmental applications.

Six cobalt gold (CoAu) electrodes were prepared by electroless deposition using different gold-containing solutions (acidic and weakly acidic) and different Au deposition times. Characterization of CoAu electrodes was done by scanning electron microscopy with energy-dispersive X-ray spectroscopy, N2-sorption, and X-ray powder diffraction techniques. The possibility of using the prepared electrodes in environmental applications, i.e., for the electrochemical sensing of a trace amount of arsenic(iii) in weakly alkaline media was assessed. Employing the CoAu electrode (prepared by immersing Co/Cu into 1 mM HAuCl4 (pH 1.8) at 30 °C for 30 s) under optimized conditions (deposition potential -0.7 V and deposition time of 60 s), a low limit of detection of 2.16 ppb was obtained. Finally, this CoAu electrode showed activity for arsenic oxidation in the presence of Cu(ii) as a model interferent as well as in real samples. Furthermore, the use of CoAu electrode as an anode in fuel cells, namely, direct borohydride - hydrogen peroxide fuel cells was also assessed. A peak power density of 191 mW cm-2 was attained at 25 °C for DBHPFC with CoAu anode at a current density of 201 mA cm-2 and cell voltage of 0.95 V, respectively. The peak power density further increased with the increase of the operating temperature to 55 °C.

Rational design of mixed ionic-electronic conducting membranes for oxygen transport.

The mixed ionic-electronic conducting (MIEC) oxides have generated significant research efforts in the scientific community during the last 40 years. Since then, many MIEC compounds, most of which are based on perovskite oxides, have been synthesized and characterized. These compounds, when heated to high temperatures, form solid ceramic membranes with high oxygen ionic and electrical conductivity. The driving force for oxygen ion transport is the ionic transfer of oxygen from the air as a result of the differential partial pressure of oxygen across the membrane. Electronic and ionic transport in a range of MIEC materials has been studied using the defect theory, particularly when dopants are introduced to the compound of interest. As a result, many types of ionic oxygen transport limits exist, each with a distinct phase shift depending on the temperature and partial pressure of oxygen in use. In combination with theoretical principles, this work attempts to evaluate the research community's major and meaningful achievements in this subject throughout the preceding four decades.

Facile Synthesis of Low-Cost Copper-Silver and Cobalt-Silver Alloy Nanoparticles on Reduced Graphene Oxide as Efficient Electrocatalysts for Oxygen Reduction Reaction in Alkaline Media.

Copper-silver and cobalt-silver alloy nanoparticles deposited on reduced graphene oxide (CuAg/rGO and CoAg/rGO) were synthesized and examined as electrocatalysts for oxygen reduction reaction (ORR) and hydrogen peroxide reduction reaction (HPRR) in alkaline media. Characterization of the prepared samples was done by transmission electron microscopy (TEM), Fourier-transform infrared spectroscopy (FTIR), Raman spectroscopy, X-ray diffraction analysis (XRD), and scanning electron microscopy with integrated energy-dispersive X-ray spectroscopy (SEM-EDS). CuAg/rGO and CoAg/rGO nanoparticles diameter ranged from 0.4 to 9.2 nm. The Ag loading was ca. 40 wt.% for both electrocatalysts, with that for Cu and Co being 35 and 17 wt.%, respectively. CoAg/rGO electrocatalyst showed a Tafel slope of 109 mV dec-1, significantly lower than that for CuAg/rGO (184 mV dec-1), suggesting faster ORR kinetics. Additionally, a higher diffusion current density was obtained for CoAg/rGO (-2.63 mA cm-2) than for CuAg/rGO (-1.74 mA cm-2). The average value of the number of electrons transferred during ORR was 2.8 for CuAg/rGO and 3.3 for CoAg/rGO electrocatalyst, further confirming the higher ORR activity of the latter. On the other hand, CuAg/rGO showed higher peak current densities (-3.96 mA cm-2) for HPRR compared to those recorded for CoAg/rGO electrocatalyst (-1.96 mA cm-2).

Platinum-Dysprosium Alloys as Oxygen Electrodes in Alkaline Media: An Experimental and Theoretical Study.

Platinum-dysprosium (Pt-Dy) alloys prepared by the arc melting technique are assessed as potential electrodes for the oxygen reduction reaction (ORR) using voltammetry and chronoamperometry in alkaline media. A relatively small change (10 at.%) in the alloy composition brought a notable difference in the alloys' performance for the ORR. Pt40Dy60 electrode, i.e., the electrode with a lower amount of Pt, was identified to have a higher activity towards ORR as evidenced by lower overpotential and higher current densities under identical experimental conditions. Furthermore, DFT calculations point out the unique single-atom-like coordination and electronic structure of Pt atoms in the Pt40Dy60 surface as responsible for enhanced ORR activity compared to the alloy with a higher Pt content. Additionally, Pt-Dy alloys showed activity in the oxygen evolution reaction (OER), with the OER current density lower than that of pure Pt.

Advanced Materials for Electrochemical Energy Conversion and Storage Devices.

Electrochemical energy conversion and storage is attracting particular attention due to the drawbacks and limitations of existing fossil fuel-based technologies [...].

Carbon-Supported Trimetallic Catalysts (PdAuNi/C) for Borohydride Oxidation Reaction.

The synthesis of palladium-based trimetallic catalysts via a facile and scalable synthesis procedure was shown to yield highly promising materials for borohydride-based fuel cells, which are attractive for use in compact environments. This, thereby, provides a route to more environmentally friendly energy storage and generation systems. Carbon-supported trimetallic catalysts were herein prepared by three different routes: using a NaBH4-ethylene glycol complex (PdAuNi/CSBEG), a NaBH4-2-propanol complex (PdAuNi/CSBIPA), and a three-step route (PdAuNi/C3-step). Notably, PdAuNi/CSBIPA yielded highly dispersed trimetallic alloy particles, as determined by XRD, EDX, ICP-OES, XPS, and TEM. The activity of the catalysts for borohydride oxidation reaction was assessed by cyclic voltammetry and RDE-based procedures, with results referenced to a Pd/C catalyst. A number of exchanged electrons close to eight was obtained for PdAuNi/C3-step and PdAuNi/CSBIPA (7.4 and 7.1, respectively), while the others, PdAuNi/CSBEG and Pd/CSBIPA, presented lower values, 2.8 and 1.2, respectively. A direct borohydride-peroxide fuel cell employing PdAuNi/CSBIPA catalyst in the anode attained a power density of 47.5 mW cm-2 at room temperature, while the elevation of temperature to 75 °C led to an approximately four-fold increase in power density to 175 mW cm-2. Trimetallic catalysts prepared via this synthesis route have significant potential for future development.

Bimetallic Co-Based (CoM, M = Mo, Fe, Mn) Coatings for High-Efficiency Water Splitting.

Bimetallic cobalt (Co)-based coatings were prepared by a facile, fast, and low-cost electroless deposition on a copper substrate (CoFe, CoMn, CoMo) and characterized by scanning electron microscopy with energy dispersive X-ray spectroscopy and X-ray diffraction analysis. Prepared coatings were thoroughly examined for hydrogen evolution reaction (HER) and oxygen evolution reaction (OER) in alkaline solution (1 M potassium hydroxide, KOH) and their activity compared to that of Co and Ni coatings. All five coatings showed activity for both reactions, where CoMo and Co showed the highest activity for HER and OER, respectively. Namely, the highest HER current density was recorded at CoMo coating with low overpotential (61 mV) to reach a current density of 10 mA·cm-2. The highest OER current density was recorded at Co coating with a low Tafel slope of 60 mV·dec-1. Furthermore, these coatings proved to be stable under HER and OER polarization conditions.

Carbon-Supported Mo2C for Oxygen Reduction Reaction Electrocatalysis.

Molybdenum carbide (Mo2C)-based electrocatalysts were prepared using two different carbon supports, commercial carbon nanotubes (CNTs) and synthesised carbon xerogel (CXG), to be studied from the point of view of both capacitive and electrocatalytic properties. Cation type (K+ or Na+) in the alkaline electrolyte solution did not affect the rate of formation of the electrical double layer at a low scan rate of 10 mV s-1. Conversely, the different mobility of these cations through the electrolyte was found to be crucial for the rate of double-layer formation at higher scan rates. Molybdenum carbide supported on carbon xerogel (Mo2C/CXG) showed ca. 3 times higher double-layer capacity amounting to 75 mF cm-2 compared to molybdenum carbide supported on carbon nanotubes (Mo2C/CNT) with a value of 23 mF cm-2 due to having more than double the surface area size. The electrocatalytic properties of carbon-supported molybdenum carbides for the oxygen reduction reaction in alkaline media were evaluated using linear scan voltammetry with a rotating disk electrode. The studied materials demonstrated good electrocatalytic performance with Mo2C/CXG delivering higher current densities at more positive onset and half-wave potential. The number of electrons exchanged during oxygen reduction reaction (ORR) was calculated to be 3, suggesting a combination of four- and two-electron mechanism.