Novel setup for rapid phase contrast CT imaging of heavy and bulky specimens.

This work introduces a novel setup for computed tomography of heavy and bulky specimens at the SYRMEP beamline of the Italian synchrotron Elettra. All the key features of the setup are described and the first application to off-center computed tomography scanning of a human chest phantom (approximately 45 kg) as well as the first results for vertical helical acquisitions are discussed.

Study of the Spatio-Chemical Heterogeneity of Tannin-Furanic Foams: From 1D FTIR Spectroscopy to 3D FTIR Micro-Computed Tomography.

Tannin-furanic rigid foams are bio-based copolymers of tannin plant extract and furfuryl alcohol, promising candidates to replace synthetic insulation foams, as for example polyurethanes and phenolics, in eco-sustainable buildings thanks to their functional properties, such as lightness of the material and fire resistance. Despite their relevance as environmental-friendly alternatives to petroleum derivatives, many aspects of the polymerization chemistry still remain unclear. One of the open issues is on the spatial heterogeneity of the foam, i.e., whether the foam constituents prevalently polymerize in spatially segregated blocks or distribute almost homogenously in the foam volume. To address this matter, here we propose a multiscale FTIR study encompassing 1D FTIR spectroscopy, 2D FTIR imaging and 3D FTIR micro-tomography (FTIR-µCT) on tannin-furanic rigid foams obtained by varying the synthesis parameters in a controlled way. Thanks to the implementation of the acquisition and processing pipeline of FTIR-µCT, we were able for the first time to demonstrate that the polymer formulations influence the spatial organization of the foam at the microscale and, at the same time, prove the reliability of FTIR-µCT data by comparing 2D FTIR images and the projection of the 3D chemical images on the same plane.

A compact and flexible induction furnace for in situ X-ray microradiograhy and computed microtomography at Elettra: design, characterization and first tests.

A compact and versatile induction furnace for in situ high-resolution synchrotron and laboratory hard X-ray microradiography and computed microtomography is described. The furnace can operate from 773 to 1723 K. Its programmable controller enables the user to specify multiple heating and cooling ramp rates as well as variable dwell times at fixed temperatures allowing precise control of heating and cooling rates to within 5 K. The instrument can work under a controlled atmosphere. Thanks to the circular geometry of the induction coils, the heat is homogeneously distributed in the internal volume of the graphite cell (ca. 150 mm3) where the sample holder is located. The thermal gradient within the furnace is less than 5 K over a height of ca. 5 mm. This new furnace design is well suited to the study of melting and solidification processes in geomaterials, ceramics and several metallic alloys, allowing fast heating (tested up to 6.5 K s-1) and quenching (up to 21 K s-1) in order to freeze the sample microstructure and chemistry under high-temperature conditions. The sample can be held at high temperatures for several hours, which is essential to follow phenomena with relatively slow dynamics, such as crystallization processes in geomaterials. The utility of the furnace is demonstrated through a few examples of experimental applications performed at the Elettra synchrotron laboratory (Trieste, Italy).

In vivo low-dose phase-contrast CT for quantification of functional and anatomical alterations in lungs of an experimental allergic airway disease mouse model.

Introduction: Synchrotron-based propagation-based imaging (PBI) is ideally suited for lung imaging and has successfully been applied in a variety of in vivo small animal studies. Virtually all these experiments were tailored to achieve extremely high spatial resolution close to the alveolar level while delivering high x-ray doses that would not permit longitudinal studies. However, the main rationale for performing lung imaging studies in vivo in small animal models is the ability to follow disease progression or monitor treatment response in the same animal over time. Thus, an in vivo imaging strategy should ideally allow performing longitudinal studies. Methods: Here, we demonstrate our findings of using PBI-based planar and CT imaging with two different detectors-MÖNCH 0.3 direct conversion detector and a complementary metal-oxide-semiconductor (CMOS) detector (Photonics Science)-in an Ovalbumin induced experimental allergic airway disease mouse model in comparison with healthy controls. The mice were imaged free breathing under isoflurane anesthesia. Results: At x-ray dose levels below those once used by commercial small animal CT devices at similar spatial resolutions, we were able to resolve structural changes at a pixel size down to 25 µm and demonstrate the reduction in elastic recoil in the asthmatic mice in cinematic planar x-ray imaging with a frame rate of up to 100 fps. Discussion: Thus, we believe that our approach will permit longitudinal small animal lung disease studies, closely following the mice over longer time spans.

High resolution propagation-based lung imaging at clinically relevant X-ray dose levels.

Absorption-based clinical computed tomography (CT) is the current imaging method of choice in the diagnosis of lung diseases. Many pulmonary diseases are affecting microscopic structures of the lung, such as terminal bronchi, alveolar spaces, sublobular blood vessels or the pulmonary interstitial tissue. As spatial resolution in CT is limited by the clinically acceptable applied X-ray dose, a comprehensive diagnosis of conditions such as interstitial lung disease, idiopathic pulmonary fibrosis or the characterization of small pulmonary nodules is limited and may require additional validation by invasive lung biopsies. Propagation-based imaging (PBI) is a phase sensitive X-ray imaging technique capable of reaching high spatial resolutions at relatively low applied radiation dose levels. In this publication, we present technical refinements of PBI for the characterization of different artificial lung pathologies, mimicking clinically relevant patterns in ventilated fresh porcine lungs in a human-scale chest phantom. The combination of a very large propagation distance of 10.7 m and a photon counting detector with [Formula: see text] pixel size enabled high resolution PBI CT with significantly improved dose efficiency, measured by thermoluminescence detectors. Image quality was directly compared with state-of-the-art clinical CT. PBI with increased propagation distance was found to provide improved image quality at the same or even lower X-ray dose levels than clinical CT. By combining PBI with iodine k-edge subtraction imaging we further demonstrate that, the high quality of the calculated iodine concentration maps might be a potential tool for the analysis of lung perfusion in great detail. Our results indicate PBI to be of great value for accurate diagnosis of lung disease in patients as it allows to depict pathological lesions non-invasively at high resolution in 3D. This will especially benefit patients at high risk of complications from invasive lung biopsies such as in the setting of suspected idiopathic pulmonary fibrosis (IPF).

Investigation of the microstructure and mineralogical composition of urinary calculi fragments by synchrotron radiation X-ray microtomography: a feasibility study.

The outcomes from the feasibility study on utilization of synchrotron radiation X-ray microtomography (SR-µCT) to investigate the texture and the quantitative mineralogical composition of selected calcium oxalate-based urinary calculi fragments are presented. The comparison of the results obtained by SR-µCT analysis with those derived from current standard analytical approaches is provided. SR-µCT is proved as a potential effective technique for determination of texture, 3D microstructure, and composition of kidney stones.

Synchrotron based planar imaging and digital tomosynthesis of breast and biopsy phantoms using a CMOS active pixel sensor.

The SYRMEP (SYnchrotron Radiation for MEdical Physics) beamline at Elettra is performing the first mammography study on human patients using free-space propagation phase contrast imaging. The stricter spatial resolution requirements of this method currently force the use of conventional films or specialized computed radiography (CR) systems. This also prevents the implementation of three-dimensional (3D) approaches. This paper explores the use of an X-ray detector based on complementary metal-oxide-semiconductor (CMOS) active pixel sensor (APS) technology as a possible alternative, for acquisitions both in planar and tomosynthesis geometry. Results indicate higher quality of the images acquired with the synchrotron set-up in both geometries. This improvement can be partly ascribed to the use of parallel, collimated and monochromatic synchrotron radiation (resulting in scatter rejection, no penumbra-induced blurring and optimized X-ray energy), and partly to phase contrast effects. Even though the pixel size of the used detector is still too large - and thus suboptimal - for free-space propagation phase contrast imaging, a degree of phase-induced edge enhancement can clearly be observed in the images.

Three dimensional visualization of engineered bone and soft tissue by combined x-ray micro-diffraction and phase contrast tomography.

Computed x-ray phase contrast micro-tomography is the most valuable tool for a three dimensional (3D) and non destructive analysis of the tissue engineered bone morphology. We used a Talbot interferometer installed at SYRMEP beamline of the ELETTRA synchrotron (Trieste, Italy) for a precise 3D reconstruction of both bone and soft connective tissue, regenerated in vivo within a porous scaffold. For the first time the x-ray tomographic reconstructions have been combined with x-ray scanning micro-diffraction measurement on the same sample, in order to give an exhaustive identification of the different tissues participating to the biomineralization process. As a result, we were able to investigate in detail the different densities in the tissues, distinguishing the 3D organization of the amorphous calcium phosphate from the collagen matrix. Our experimental approach allows for a deeper understanding of the role of collagen matrix in the organic-mineral transition, which is a crucial issue for the development of new bio-inspired composites.

Evaluation of microstructural properties of coffee beans by synchrotron X-ray microtomography: a methodological approach.

UNLABELLED: Synchrotron radiation microtomography was used as a nondestructive imaging technique to investigate the microstructural properties of green and roasted coffee beans. After image acquisition, 2D images have been reconstructed and 3D images of the beans have been then obtained. Qualitative and quantitative analysis of the images allow to fully characterize the morphological and structural features of the coffee beans. Roasting causes meaningful changes in the microstructure of the coffee bean tissue with the development in the entire bean of a porous structure with pores of different shape and size depending on the zone of the bean and cracks occurring mainly in the more external regions and between parenchyma and mucilage. The highly contrasted X-ray images have been analyzed to determine the pore size and its distribution in different regions of the coffee beans by selecting Volume-of-Interest (VoI). The use of phase-contrast hard X-rays imaging techniques represents an interesting tool of investigation of the internal structure, morphology, as well as the quality of whole coffee beans. Moreover, the high potentiality of 3D X-ray imaging and the approach used in this study could be applied in understanding the effects of roasting process conditions on the evolution of microstructural properties of the bean that may affect the stability as well the grinding and brewing performances. PRACTICAL APPLICATION: Synchrotron radiation microtomography is an elegant nondestructive imaging technique to investigate the microstructural properties of porous cellular matrices like the green and roasted coffee beans. The quantitative analysis of the resulting 2D and 3D images allows a more comprehensive and objective characterization of the sample under investigation as a whole or of extracted Volumes-of-Interest in the bean. This imaging technique could have a major role in understanding the effects of roasting process conditions on the microstructural properties of the bean.