New fired bricks based on municipal solid waste incinerator bottom ash.

The main objective of this work was to study the sintering process and technological properties of new fired bricks based on high amount of post-treated municipal solid waste incinerator bottom ash and refractory clay. In addition, the effect of the minor addition of flux (Na2CO3) or reinforce (corundum) was also highlighted. Several methods were used to study the effect of compositions variations on the sintering process, structure and the mechanical characteristics of the test briquettes. Differential thermal analysis (TG/DTA) and dilatometry techniques were applied to study the thermal behaviour while scanning electron microscopy coupled with energy-dispersive X-ray spectroscopy and high-temperature X-ray diffraction were used to elucidate the structure and the phase composition. The mechanical characteristics were estimated by micro-indentation, strength and various physical tests (porosity, linear shrinkage and water absorption, etc). The results highlight the possibility to use very high amount of municipal solid waste incinerator bottom ashes in the production of new fired bricks with good performances at all levels. It is also shown that the addition of additives managed the final properties, affecting the crystal phase formation, porosity and greatly the strength of the samples.

An efficient and fast analytical procedure for the bromine determination in waste electrical and electronic equipment plastics.

In this study, X-ray fluorescence (XRF) spectroscopy was used, in combination with micro-Raman spectroscopy, for a fast determination of bromine concentration and then of brominated flame retardants (BFRs) compounds in waste electrical and electronic equipments. Different samples from different recycling industries were characterized to evaluate the sorting performances of treatment companies. This investigation must be considered of prime research interest since the impact of BFRs on the environment and their potential risk on human health is an actual concern. Indeed, the new European Restriction of Hazardous Substances Directive (RoHS 2011/65/EU) demands that plastics with BFRs concentration above 0.1%, being potential health hazards, are identified and eliminated from the recycling process. Our results show the capability and the potential of Raman spectroscopy, together with XRF analysis, as effective tools for the rapid detection of BFRs in plastic materials. In particular, the use of these two techniques in combination can be considered as a promising method suitable for quality control applications in the recycling industry.

Comparison of biomethane production and digestate characterization for selected agricultural substrates in Italy.

Starting from (but not limited to) their importance in the Italian context, three agricultural substrates, two of fruit origin (grape seeds and plum stones) and one of herbaceous origin (woad), were comparatively tested for both biomethane production and digestate characterization. The anaerobic digestion tests showed that grape seeds had the highest net methane production of 253.0 NmL g volatile solids (VS)(-1), followed by plum stones, whose best resulting net methane production was 174.7 NmL gVS(-1), and finally by woad with a net methane production of 153.1 NmL gVS(-1). Interestingly, the best methane productions of the fruit substrates were obtained with different substrate to inoculum ratios (on a VS basis), 1:1 for grape seeds but 2:1 for plum stones. On the other hand, a three-month ageing of woad caused a limited reduction of methane production. The estimation of obtained degrees of conversion, carried out on a chemical oxygen demand (COD) basis for the specific tests achieving the respective best methane productions, gave values of 48%, 31%, and 33% for grape seeds, plum stones, and woad, respectively. The estimated degrees of conversion were evaluated along with the respective methane productions and substrate COD/VS ratios. The comparison of Fourier transform infrared (FT-IR) spectra and differential thermal analysis (DTA) profiles, carried out for selected digestates in pairs, revealed some distinctive differences in the relative intensities or presence and absence of particular peaks in the FT-IR spectra and in the relative intensities of the exothermic peaks or horizontal curve shifting of the DTA profiles.

Anaerobic digestion of selected Italian agricultural and industrial residues (grape seeds and leather dust): combined methane production and digestate characterization.

A combined experimental evaluation of methane production (obtained by anaerobic digestion) and detailed digestate characterization (with physical-chemical, thermo-gravimetric and mineralogical approaches) was conducted on two organic substrates, which are specific to Italy (at regional and national levels). One of the substrates was grape seeds, which have an agricultural origin, whereas the other substrate was vegetable-tanned leather dust, which has an industrial origin. Under the assumed experimental conditions of the performed lab-scale test series, the grape seed substrate exhibited a resulting net methane production of 175.0 NmL g volatile solids (VS)(-1); hence, it can be considered as a potential energy source via anaerobic digestion. Conversely, the net methane production obtained from the anaerobic digestion of the vegetable-tanned leather dust substrate was limited to 16.1 NmL gVS(-1). A detailed characterization of the obtained digestates showed that there were both nitrogen-containing compounds and complex organic compounds present in the digestate that was obtained from the mixture of leather dust and inoculum. As a general perspective of this experimental study, the application of diversified characterization analyzes could facilitate (1) a better understanding of the main properties of the obtained digestates to evaluate their potential valorization, and (2) a combination of the digestate characteristics with the corresponding methane productions to comprehensively evaluate the bioconversion process.

Functionalization of ceramic tile surface by sol-gel technique.

The aim of this investigation was the surface functionalization of industrial ceramic tiles by sol-gel technique to improve at the same time the cleanability of unglazed surfaces. This objective was pursued through the design and preparation of nanostructured coating that was deposited on polished unglazed tiles by air-brushing. In particular TiO(2)-SiO(2) binary film with 1, 2 or 5wt% of titania were prepared by using tetraethoxysilane and titania nanoparticles as precursors. The obtained films were characterized by scratch tests to verify the adhesion of the coatings to the polished tiles. To mainly evaluate the effect of the thermal treatment (temperature range 100-600 degrees C) on the photocatalicity of the coatings, the films were studied under UV exposure by contact angle measurements and cleanability test. Particular attention has been paid to preserve the aesthetical aspect of the final product and the obtained hue variation was evaluated by means of UV-visible spectroscopy and colorimetric analysis.